ASTM D4165-2006(2012) Standard Test Method for Cyanogen Chloride in Water&thinsp 《水中氯化氰含量的标准试验方法》.pdf
《ASTM D4165-2006(2012) Standard Test Method for Cyanogen Chloride in Water&thinsp 《水中氯化氰含量的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM D4165-2006(2012) Standard Test Method for Cyanogen Chloride in Water&thinsp 《水中氯化氰含量的标准试验方法》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D4165 06 (Reapproved 2012)Standard Test Method forCyanogen Chloride in Water1This standard is issued under the fixed designation D4165; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe
2、r in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of cyanogenchloride in water. Cyanogen chloride is normally present onlyat very low concentrations
3、; it is a very labile and sparselysoluble gaseous compound. Water samples may contain cya-nogen chloride after the chlorination of waste waters contain-ing cyanide or thiocyanate compounds.1.2 Cyanogen chloride is unstable. A quick test using a spotplate or comparator as soon as the sample is collec
4、ted may bethe best test, reducing the loss of cyanogen chloride during thetime lapse between sampling and analysis. (See Fig. 1 for atypical decay curve for cyanogen chloride in a solution.)1.3 This test method has been used successfully withreagent water. The analyst is responsible for determiningw
5、hether the test method is applicable to the water matrix beingtested. Reference is made to Test Method D of Test MethodsD2036 which is based on similar chemical reactions and hasbeen evaluated by collaborative testing in this matrix.1.4 The lower limit of detectability is 0.005 mg CN/L.1.5 This stan
6、dard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. Specific hazardstatements a
7、re given in Note 1 and Note 2 and Section 9.2. Referenced Documents2.1 ASTM Standards:2D1129 Terminology Relating to WaterD1193 Specification for Reagent WaterD2036 Test Methods for Cyanides in WaterD3370 Practices for Sampling Water from Closed ConduitsD3856 Guide for Management Systems in Laborato
8、riesEngaged in Analysis of WaterD4210 Practice for Intralaboratory Quality Control Proce-dures and a Discussion on Reporting Low-Level Data3D5789 Practice for Writing Quality Control Specificationsfor Standard Test Methods for Organic Constituents3D5847 Practice for Writing Quality Control Specifica
9、tionsfor Standard Test Methods for Water AnalysisE60 Practice for Analysis of Metals, Ores, and RelatedMaterials by SpectrophotometryE275 Practice for Describing and Measuring Performanceof Ultraviolet and Visible Spectrophotometers3. Terminology3.1 DefinitionsFor definitions of terms used in this t
10、estmethod, refer to Terminology D1129.1This test method is under the jurisdiction of ASTM Committee D19 on Waterand is the direct responsibility of Subcommittee D19.06 on Methods forAnalysis forOrganic Substances in Water.Current edition approved June 15, 2012. Published August 2012. Originallyappro
11、ved in 1982. Last previous edition approved in 2006 as D4165 06 DOI:10.1520/D4165-06R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summa
12、ry page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.FIG. 1 Cyanogen Chloride Stability1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4. Summary of Test Method4.1
13、The water sample is mixed with a pyridine-barbituricacid solution and the color produced is measured with aspectrophotometer.5. Significance and Use5.1 The presence of cyanogen chloride in chlorinated sani-tary and industrial effluents and therefore receiving waters is ofconcern because of its toxic
14、ity to aquatic life.5.2 This test method provides an analytical procedure formeasuring cyanogen chloride in water.5.3 This test method is applicable for clean metal finishingand chlorinated sanitary and industrial effluents, and also canbe used to establish process control of cyanide destruction byc
15、hlorination in waste water treatment facilities.6. Interferences6.1 Color and turbidity can interfere.7. Apparatus7.1 Spectrophotometer or Filter Photometer, suitable formeasurement in the region of 578 nm, using 1.0-cm absorptioncells. Filter photometers and photometric practices used in thistest m
16、ethod shall conform to Practice E60. Spectrophotometersshall conform to Practice E275.8. Reagents8.1 Purity of ReagentsReagent grade chemicals shall beused in all tests. Unless otherwise indicated, it is intended thatall reagents shall conform to the specifications of the Commit-tee onAnalytical Rea
17、gents of theAmerican Chem-ical Society,where such specifications are available.4Other grades may beused, provided it is first ascertained that the reagent is ofsufficiently high purity to permit its use without lessening theaccuracy of the determination.8.2 Purity of Water Unless otherwise indicated
18、, refer-ences to water shall be understood to mean reagent water thatmeets the purity specifications of Type I or Type II waterpresented in Specification D1193.8.3 Barbituric Acid.8.4 Chloramine-T Solution (10 g/L)Dissolve 1.0 g of thewhite colored, water-soluble grade powder chloramine-T in100 mL o
19、f water. Store in an amber bottle under refrigeration.Prepare fresh weekly.8.5 Cyanide Solution, Stock (1 mL = 250 g CN)Dissolve 0.6258 g of potassium cyanide (KCN) in 40 mL ofsodium hydroxide solution (40 g/L). Dilute to 1 L with water.Mix thoroughly; standardize with standard silver nitrate solu-t
20、ion (see Section 8 of Test Methods D2036).NOTE 1Warning: Because KCN is highly toxic, avoid contact orinhalation. Do not pipet by mouth (see Section 9).8.5.1 Cyanide Solution I, Standard (1 mL = 25 g CN)Dilute a calculated volume (approximately 100 mL) of KCNstock solution to 1 L with NaOH solution
21、(1.6 g/L).8.5.2 Cyanide Solution II, Standard (1 mL = 2.5 g CN)Dilute exactly 100 mL of cyanide Solution I to 1 L with NaOHsolution (1.6 g/L).8.5.3 Cyanide Solution III, Standard (1 mL = 0.25 gCN)Dilute exactly 100 mL of cyanide Solution II to 1 Lwith NaOH solution (1.6 g/L). Prepare fresh solution
22、daily andprotect from light.8.6 Phosphate Buffer Dissolve 138 g of sodium dihydro-gen phosphate (NaH2PO4H2O) in water and dilute to 1 L.Refrigerate this solution.8.7 Pyridine.NOTE 2Warning: Pyridine may cause irritation to the skin andrespiratory tract. Do not pipet by mouth (see Section 9).8.8 Pyri
23、dine-Barbituric Acid ReagentPlace 15 g of bar-bituric acid in a 250-mL volumetric flask and add just enoughwater to wash the sides of the flask and wet the barbituric acid.Add 75 mL of pyridine and mix. Add 15 mL of hydrochloricacid (sp gr 1.19), mix, and cool to room temperature. Dilute tovolume wi
24、th water and mix until all of the barbituric acid isdissolved. This solution is usable for about 6 months if storedin a cold, dark place.8.9 Sodium Hydroxide Solution (40 g/L)Dissolve 40 g ofsodium hydroxide in water and dilute to 1 L with water.8.10 Sodium Hydroxide Solution (1.6 g/L)Dilute 40 mLof
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD416520062012STANDARDTESTMETHODFORCYANOGENCHLORIDEINWATERTHINSP 水中 氯化氰 含量 标准 试验 方法 PDF

链接地址:http://www.mydoc123.com/p-516425.html