JASO C428-2001 英文版 汽车——驻车试验规程.pdf
《JASO C428-2001 英文版 汽车——驻车试验规程.pdf》由会员分享,可在线阅读,更多相关《JASO C428-2001 英文版 汽车——驻车试验规程.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、日本汽车标准_JASO C428-2001 英文版 汽车驻车试验规程_JAPANESE AUTOMOBILE STANDARD Division MI M2 M3 JASO C428: 2001 Application Total weight Passenger capacity Passenger car 5 t or less 9 people or less Class 1 bus 5 t or less Over 10 people Class 2 bus Over 5 t Over 10 DeoDle Road vehicles - Parking brake test proce
2、dure 1. Scope proper operation. These specifications are not applicable to motorcycles, motorcycles with side car, light motor vehicles with caterpillar or sledge or automobiles with a maximum speed of less than 25 kmlh. This Standard specifies test procedures for parking brakes installed on actual
3、vehicles to confirm NI N2 N3 o1 02 03 04 2. Applicable Publications The following publications form a part of this Standard to the extent specified herein. The latest edition of all publications shall apply. II Class 1 truck 3.5 t or less Class 2 truck Over 3.5 t to 12 t Class 3 truck Over 12 t Clas
4、s 1 trailer Total axle load 0.75 t or less Class 2 trailer Total axle load over 0.75 t to 3.5 t Class 3 trailer Total axle load over 3.5 t to 10 t Class 4 trailer Total axle load over 10 t JIS DO210 JASO C436 General Rules of Brake Test Method for Automobiles and Motorcycles Parking Brake Device Dyn
5、amometer Test Procedures Division Type A Type B Type C (Center 3. Definitions Definitions of major terms used herein, other than the term stated below, are as specified in JIS Initial brake temperature D0210, Item 2. Temperature at which brake application is initiated Type Frequent use of friction m
6、aterial for main brakes - Built into wheel brake Frequent use of friction material for parking brake - Built into wheel brake Exclusive use of friction material for parking brake - Mounted on 4. Test conditions 4.1 4.1.1 Vehicle divisions Vehicles and parking brake divisions Test vehicles shall be c
7、lassified into divisions according to application, total weight and passenger capacity as specified in Table 1. Table 1 Vehicle divisions 4.1.2 Parking brake divisions Parking brakes shall be classified into divisions according to type as specified in Table 2. Table 2 Parking brake divisions I type)
8、 I transmission or transmission shaft 4.2 Vehicle condition Requirements are as specified in JIS D0210, Item 4.1. Requirements are as specified in JIS D0210, Item 4.3 4.3 Condition of individual brake parts 4.4 Track and weather conditions Requirements are as specified in JIS D0210, Item 4.2 1 JASO
9、C428: 2001 Initial brake speed kmlh Pre-braking brake temperature C Braking deceleration speed mls Braking repetitions times 4.5 Temperature measurement 4.6 Lever operating force a) Operating force for hand operated types, shall be measured at the center of hand grip. Requirements are as specified i
10、n JIS D0210, Item 6. Requirements are as specified below. When the center is not easily distinguished, the measurement point shall be 40 mm from the tip of the lever excluding the button portion. b) A calibrated operating force meter or an equivalent instrument shall be used. Measurement is not requ
11、ired for spring brakes. c) Operating force shall be applied in the direction used to apply the brake lever or brake pedal. 4.7 Fitting conditions specified in Tables 3 and 4, parking brake division. a) Type A and Type C (Center) Tests shall be conducted in the forward direction. Fitting shall be per
12、formed under the conditions Requirements are as specified in Table 3. Type A Type c MI NI M2, M3, N2, N3 I 01, 02, 03, 04 All divisions 65 60 60 10 120 120 150 1 O0 3.5 3.0 3.0 1 .o 200 200 300 30 Table 3 Fitting conditions for Type A and Type C (Center) Initial brake speed kmlh Pre-braking brake te
13、mperature C Operating force N Braking time S Braking repetitions Times All divisions 30 100 or less 5 Hand operation - 100, Pedal operation - 150 30 b) Type B A dragging test shall be performed as specified in Table 4. Conditions shall be in accordance with the requirements of JASO or the automobile
14、 manufacturer. The dragging method is not applicable to spring brakes, and therefore the stop method or a method specified by the manufacturer shall be used. Division MI M2, N2, M3 N3 01, 02, 03, 04 All Table 4 Fitting conditions for type B Maximum allowable control force operation Remark Incline or
15、 braking Pedal operation Vehicle efficiency % Hand Passenger car 20 400 500 - Trucks, busses 18 600 700 - Trailers 18 600 - Connected Includes (Conditions conditions for apply to parking connected brake for traction 12 600 700 passenger cars vehicle alone) and trailers , (total weight 750 kg or less
16、). 4.8 Inclined test track and operating force Requirements are as specified in Table 5. Table 5 Inclined test track and operating force conditions 2 JAS0 C428: 2001 Parking brake performance specified in Table 5 shall be applied for spring brakes under normal brake valve operation Parking brakes ac
17、tivated by two or more operations shall be tested after the brake is operated the according to design standards. 5. Test methods 5.1 Test methods for inclined test tracks a) The test shall be performed on both upward and downward inclines. b) The test vehicle shall be driven on a test track with the
18、 incline specified in Table 5, the gear shifted c) The stop condition shall be confirmed, the parking brake applied with the force specified in Table 5, and the main brake released. The operating force of the parking brake shall released and the stop condition shall be confirmed. the trailer parking
19、 brake is not interlocked with the traction vehicle, the stop condition shall be confirmed in a similar manner after the trailer parking brake is activated as specified. However, for vehicles connected to a tractor or passenger car, and trailers of 750 kg or less, only the traction vehicle parking b
20、rake shall be applied. Requirements are as specified below. to the neutral position, and the vehicle brought to a full stop by applying the main brake. For connected vehicles, the test shall be performed under the applicable conditions. In cases where d) In the event the stopped condition cannot be
21、maintained, the specified operating force may be applied a maximum of two times without loosening the ratchet after the vehicle is stopped by the main brake. e) For spring brakes, the operation stated in b) shall be performed first. The main brake shall be released by activating the operation valve
22、and the stopped condition shall be confirmed. When the inclined test track in Table 5 is not available, the test may be performed after the mass of the test vehicle is adjusted according to the following equation: w x sin(tan-l B) w, =siii(tanB,) where, W,: Total test vehicle weight after adjustment
23、 (kg) Test vehicle nominal weight (kg) Angle of inclined track used for test (%)/IO0 Angle of inclined track specified by division (%)/I O0 W: B,: B: 5.2 Braking capability test method a) The vehicle shall be set on a roller drive brake test apparatus (hereafter referred to as the tester) Requiremen
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JASO C428 2001 英文 汽车 试验 规程