ASTM D714-2002(2017) Standard Test Method for Evaluating Degree of Blistering of Paints《涂料起泡度评定的标准试验方法》.pdf

《ASTM D714-2002(2017) Standard Test Method for Evaluating Degree of Blistering of Paints《涂料起泡度评定的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D714-2002(2017) Standard Test Method for Evaluating Degree of Blistering of Paints《涂料起泡度评定的标准试验方法》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D714 02 (Reapproved 2017)Standard Test Method forEvaluating Degree of Blistering of Paints1This standard is issued under the fixed designation D714; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revi

2、sion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This test method employs photographic ref

3、erence stan-dards to evaluate the degree of blistering that may developwhen paint systems are subjected to conditions which willcause blistering. While primarily intended for use on metal andother nonporous surfaces, this test method may be used toevaluate blisters on porous surfaces, such as wood,

4、if the sizeof blisters falls within the scope of these reference standards.When the reference standards are used as a specification ofperformance, the permissible degree of blistering of the paintsystem shall be agreed upon by the purchaser and the seller.1.2 This standard does not purport to addres

5、s all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.3 This international standard was develop

6、ed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Docume

7、nts2.1 ASTM Adjuncts:Reference Standards for Blistering of Paint Coatings23. Significance and Use3.1 A phenomenon peculiar to painted surfaces is theformation of blisters relative to some system weakness. Thistest method provides a standard procedure of describing thesize and density of the blisters

8、 so that comparisons of severitycan be made.4. Reference Standards4.1 The photographic reference standards are glossyprints.2Figs. 1-4 are reproductions of these standards and areincluded to illustrate two characteristics of blistering: size andfrequency.4.2 SizeReference standards have been selecte

9、d for foursteps as to size on a numerical scale from 10 to 0, in which No.10 represents no blistering. Blistering standard No. 8 representsthe smallest size blister easily seen by the unaided eye.Blistering standards Nos. 6, 4, and 2 represent progressivelylarger sizes.4.3 FrequencyReference standar

10、ds have been selected forfour steps in frequency at each step in size, designated asfollows:Dense, D,Medium dense, MD,Medium, M, andFew, F.NOTE 1Aquantitative physical description of blistering would includethe following characteristics determined by actual count:Size distribution in terms of mensur

11、ation units,Frequency of occurrence per unit area,Pattern of distribution over the surface, andShape of blisterFor the usual tests, an actual count is more elaborate than is necessary.5. Procedure5.1 Subject the paint film to the test conditions agreed uponby the purchaser and the seller. Then evalu

12、ate the paint film forthe degree of blistering by comparison with the photographicreference standards in Figs. 1-4.6. Report6.1 Report blistering as a number (Note 2) designating thesize of the blisters and a qualitative term or symbol indicatingthe frequency.6.2 Intermediate steps in size or freque

13、ncy of blisters maybe judged by interpolation.6.3 When the distribution of blisters over the area has anonuniform pattern, use an additional phrase to describe thedistribution, such as “small clusters,” or “large patches.”1This test method is under the jurisdiction of ASTM Committee D01 on Paintand

14、Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.25 on Evaluation of Weathering Effects.Current edition approved Dec. 1, 2017. Published December 2017. Originallyapproved in 1943. Last previous edition approved in 2009 as D71402 (2009). DOI:10.1520/D0

15、714-02R17.2Glossy prints of the photographic reference standards showing types ofblistering are available from ASTM International Headquarters. Order Adjunct No.ADJD0714. Original adjunct produced in 1986.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2

16、959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical

17、 Barriers to Trade (TBT) Committee.1NOTE 2The number refers to the largest size blister that is numerousenough to be representative of the specimen. For example, photographicstandard No. 4, “Dense,” has blisters ranging in size from about No. 7 toNo. 4, inclusive.6.4 The pictorial representations in

18、 this standard which arepublished in the Book of Standards are sufficient in order toconduct the evaluation. It is preferable however, to use theoriginal photographs or drawings when available.7. Keywords7.1 blistering; corrosion; evaluations; reference standardsFew MediumFIG. 1 Blister Size No. 2Me

19、dium Dense DenseFIG. 1 Blister Size No. 2 (continued)D714 02 (2017)2Few MediumFIG. 2 Blister Size No. 4Medium Dense DenseFIG. 2 Blister Size No. 4 (continued)D714 02 (2017)3Few MediumFIG. 3 Blister Size No. 6Medium Dense DenseFIG. 3 Blister Size No. 6 (continued)D714 02 (2017)4Few MediumFIG. 4 Blist

20、er size No. 8Medium Dense DenseFIG. 4 Blister Size No. 8 (continued)D714 02 (2017)5ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the

21、validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your

22、comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments h

23、ave not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multip

24、le copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 02 (2017)6