ASTM C1330-2018 Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants.pdf
《ASTM C1330-2018 Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants.pdf》由会员分享,可在线阅读,更多相关《ASTM C1330-2018 Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C1330 02 (Reapproved 2013)C1330 18Standard Specification forCylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants1This standard is issued under the fixed designation C1330; the number immediately following the designation indicates the year oforiginal adoption or, in the
2、 case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the basic requirements for cylindrical sealant backing to be
3、used with cold liquid applied sealantsfor use in building seals.1.2 Cylindrical sealant backing serves one or more of the following functions:1.2.1 Limits the amount and depth of sealant applied into a joint,1.2.2 Acts as a bond breaker to allow joint movement without undue stress to the sealant,1.2
4、.3 Provides a form to assist the sealant in developing the proper shape factor, and1.2.4 Acts as a barrier to the flow of sealant through the joint.1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other ASTMcommittees or other organizations
5、.1.4 This specification may involve hazardous materials, operations, and equipment. This standard does not purport to addressall of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriatesafety safety, health, and healthenv
6、ironmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standard
7、s, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2C717 Terminology of Building Seals and SealantsC1016 Test Method for Determination of Water Absorption of Sealant Backing (Joint Filler) Material
8、C1087 Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural GlazingSystemsC1253 Test Method for Determining the Outgassing Potential of Sealant BackingD1622 Test Method for Apparent Density of Rigid Cellular PlasticsD1623 Test Method for Tensile and
9、 Tensile Adhesion Properties of Rigid Cellular PlasticsD5249 Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete andAsphalt Joints3. Terminology3.1 DefinitionsThe definitions for the following terms used in this standard are found in Termin
10、ology C717:3.1.1 bi-cellular sealant backing, bond breaker, closed cell, joint, open cell, outgassing, seal, sealant, sealant backing, skin.4. Classification4.1 Cylindrical sealant backings are divided into three types.1 This specification is under the jurisdiction of ASTM Committee C24 on Building
11、Seals and Sealants and is the direct responsibility of Subcommittee C24.10 onSpecifications, Guides and Practices.Current edition approved May 1, 2013Sept. 15, 2018. Published May 2013October 2018. Originally approved in 1996. Last previous edition approved in 20072013 asC133002(2007).C133002(2013).
12、 DOI: 10.1520/C1330-02R13.10.1520/C1330-18.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is n
13、ot an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropria
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC13302018STANDARDSPECIFICATIONFORCYLINDRICALSEALANTBACKINGFORUSEWITHCOLDLIQUIDAPPLIEDSEALANTSPDF

链接地址:http://www.mydoc123.com/p-464261.html