ASTM B124 B124M-2013 Standard Specification for Copper and Copper Alloy Forging Rod Bar and Shapes《锻制的铜和铜合金条材、棒材及型材标准规格》.pdf

《ASTM B124 B124M-2013 Standard Specification for Copper and Copper Alloy Forging Rod Bar and Shapes《锻制的铜和铜合金条材、棒材及型材标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B124 B124M-2013 Standard Specification for Copper and Copper Alloy Forging Rod Bar and Shapes《锻制的铜和铜合金条材、棒材及型材标准规格》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B124/B124M 12B124/B124M 13Standard Specification forCopper and Copper Alloy Forging Rod, Bar, and Shapes1This standard is issued under the fixed designation B124/B124M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, t

2、he year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification establ

3、ishes the requirements for copper and copper alloy rod, bar, and shapes intended for hot forging.The following coppers and copper alloys are involved:Copper UNS Nos. Copper Alloy UNS Nos.C11000 C35330C14500 C36500C14700 C37000C37700C46400C48200C48500C48600C49250C49255C49260C49300C49340C49350C49355C4

4、9360C61900C62300C63000C63200C64200C64210C65500C67500C67600C69300C69150C69300C70620C71520C77400C87700C87710C27450NOTE 1Additional information about forging practice and forgings produced from these alloys is given in Appendix X1 and in Specification B283.1.2 UnitsThe values stated in either SI units

5、or inch-pound units are to be regarded separately as standard. The values statedin each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining valuesfrom the two systems may result in non-conformance with the standard.1.3 This standard does no

6、t purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatoryrequirements prior to use.1 This specification is under the jurisdi

7、ction ofASTM Committee B05 on Copper and CopperAlloys and is the direct responsibility of Subcommittee B05.02 on Rod, Bar,Wire, Shapes and Forgings.Current edition approved April 1, 2012April 1, 2013. Published April 2012April 2013. Originally approved in 1939. Last previous edition approved in 2011

8、2012 asB124/B124M 11b.B124/B124M 12. DOI: 10.1520/B0124_B0124M-12.10.1520/B0124_B0124M-13.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible

9、 to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyrig

10、ht ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States12. Referenced Documents2.1 ASTM Standards:2B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and ForgingsB283 Specification for Copper and C

11、opper-Alloy Die Forgings (Hot-Pressed)E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002)3E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)3E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Ni

12、ckel-Zinc Alloys (Withdrawn 2010)3E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys (Withdrawn 2003)3E121 Test Methods for Chemical Analysis of Copper-Tellurium Alloys (Withdrawn 2010)3E478 Test Methods for Chemical Analysis of Copper Alloys2.2 Other Standard:ISO 3110, Part 2 (TC 26 Ref

13、. No. N 670 E/F) Determination of Aluminum Content: Flame Atomic Absorption SpectrometricMethod4JIS H 1068:2005 Method for Determination of Bismuth in Copper and Copper Alloys5 (Japanese Industrial Standards)3. General Requirements3.1 The following sections of Specification B249/B249M, as applicable

14、, constitute a part of this specification:3.1.1 Terminology,3.1.2 Material and Manufacture,3.1.3 Workmanship, Finish, and Appearance,3.1.4 Sampling,3.1.5 Number of Tests and Retests,3.1.6 Specimen Preparation,3.1.7 Test Methods,3.1.8 Significance of Numerical Limits,3.1.9 Inspection,3.1.10 Rejection

15、 and Rehearing,3.1.11 Certification,3.1.12 Mill Test Reports,3.1.13 Packaging and Package Marking, and3.1.14 Supplementary Requirements.3.2 In addition, when a section with a title identical to that referenced in 3.1, appears in this specification, it contains additionalrequirements that supplement

16、those appearing in Specification B249/B249M.4. Ordering Information4.1 Include the following information when placing orders for products under this specification:4.1.1 ASTM designation and year of issue (B124/B124M XX),4.1.2 Copper or Copper-Alloy UNS No. designation,4.1.3 Form (rod, bar, or shape)

17、 and size (Dimensions and Permissible Variations Section),4.1.4 Permissible Variations (Dimensions and Permissible Variations Section),4.1.5 Temper (Temper Section),4.1.6 Length (Dimensions and Permissible Variations Section),4.1.7 Quantity; total weight for each size and form,4.1.8 If the product i

18、s purchased for agencies of the U.S. government (see the Supplementary Requirements Section of thisspecification for additional requirements, if specified.)4.2 The following options are available and, when required, should be specified at the time of placing of the order:4.2.1 Mechanical Properties

19、for Temper designated (Mechanical Properties Section),4.2.2 Certification (B249/B249M),4.2.3 Test Report (B249/B249M), and4.2.4 When product is ordered for ASME Boiler and Pressure Vessel Code Application (see Certification Section ofB249/B249M).4.2.5 Shapes; dimensional tolerances required and agre

20、ed upon (see 10.1.3).2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 The last approved version of this hist

21、orical standard is referenced on www.astm.org.4 Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http:/www.ansi.org.5 Available from Japanese Industrial Standards, http/www.JIS.or.jp/.B124/B124M 1325. Materials and Manufacture5.1 Materials:5

22、.1.1 The material of manufacture shall be a cast rod, bar, or billet of the designated copper or copper-alloy of such purity andsoundness to be suitable for processing in to the products prescribed herein.5.1.2 In the event that heat identification or traceability is required, the purchaser shall sp

23、ecify the details desired.NOTE 2Due to the discontinuous nature of the processing of castings into wrought products, it is not always practical to identify a specific castinganalysis with a specific quantity of finished material.5.2 Manufacture:5.2.1 The product shall be manufactured by such hot wor

24、king, cold working, and annealing processes as to produce a uniformwrought structure in the finished product.5.2.2 The product shall be hot or cold worked to the finished size and subsequently annealed, when required, to meet the temperproperties specified.6. Chemical Composition6.1 The material sha

25、ll conform to the chemical composition requirements in Table 1 for the copper or copper alloy UNS No.designation specified in the ordering information.6.1.1 These composition limits do not preclude the presence of other elements. By agreement between the manufacturer and thepurchaser, limits may be

26、established and analysis required for unnamed elements.6.2 For alloys in which either copper or zinc is listed as “remainder,” copper or zinc is the difference between the sum of resultsof all elements determined and 100 %. When all elements in Table 1 for the specified copper-alloy are determined,

27、the sum ofresults shall be as follows:Copper Alloy UNS No. Sum of Results,% minC36500, C37000, C46400, C48200, C48500,C48600,C6915099.6C27450, C35330, C37700, C49250, C49255,C49260, C49300, C49340, C49350, C49355,C49360, C61900, C62300, C63000,C63200, C64200, C64210, C65500, C67500,C67600,C69300, C7

28、0620, C71520, C7740099.5C87700, C87710 99.27. Temper7.1 The standard tempers for products described in this specification are as follows:7.1.1 H50Extruded and drawn.7.1.2 H80Hard drawn.7.1.3 M20As hot-rolled.7.1.4 M30As hot-extruded.7.1.5 060Soft Annealed.7.1.6 O61Annealed.7.1.7 O30Hot Extruded and

29、Annealed.8. Mechanical Property Requirements8.1 Mechanical property requirements, if any, are to be established by agreement between the manufacturer and the purchaser.9. Purchases for U.S. Government9.1 When specified in the contract or purchase order, products purchased for agencies of the U.S. Go

30、vernment shall conformto the special governmental regulations specified in the Supplementary Requirements sections of this specification and ofB249/B249M.10. Dimensions and Permissible Variations10.1 The dimensions and tolerances for product described by this specification shall be as specified in S

31、pecificationB249/B249M with particular reference to the following tables and related paragraphs:10.1.1 Diameter or Distance Between Parallel Surfaces:B124/B124M 133TABLE 1 Chemical RequirementsCopperorCopperAlloyUNSNo.Composition, %Copper Lead Tin Iron Nickel(incl Co) Aluminum Silicon Manganese Zinc

32、 Sulfur Tellurium Phos-phorus Arsenic BismuthCopperPlusElementswithSpecificLimitsPresent,minC11000 99.90 minA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C14500B 99.90 minC . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.400.7 0.0040.012 . . . . . . . .

33、 .C14700B 99.90 minD . . . . . . . . . . . . . . . . . . . . . . . . 0.200.50 . . . 0.0020.005 . . . . . . . . .C27450 60.065.0 0.25 max . . . 0.35 max . . . . . . . . . . . . remainder . . . . . . . . . . . . . . . 99.5C35330 59.564.0 1.53.5 . . . . . . . . . . . . . . . . . . remainder . . . . . .

34、 . . . .02.25 . . . . . .C36500 58.061.0 0.250.7 0.25 max 0.15 max . . . . . . . . . . . . remainder . . . . . . . . . . . . . . . 99.6C37000 59.062.0 0.81.5 0.15 max . . . . . . . . . . . . remainder . . . . . . . . . . . . . . . 99.6C37700 58.061.0 1.52.5 . . . 0.30 max . . . . . . . . . . . . rem

35、ainder . . . . . . . . . . . . . . . 99.5C46400 59.062.0 0.20 max 0.501.0 0.10 max . . . . . . . . . . . . remainder . . . . . . . . . . . . . . . 99.6C48200 59.062.0 0.401.0 0.501.0 0.10 max . . . . . . . . . . . . remainder . . . . . . . . . . . . . . . 99.6C48500 59.062.0 1.32.2 0.501.0 0.10 max

36、. . . . . . . . . . . . remainder . . . . . . . . . . . . . . . 99.6C48600 59.062.0 1.02.5 .301.5 . . . . . . . . . . . . . . . remainder . . . . . . . . . .02.25 . . . . . .C49250E 58.061.0 0.09 max 0.30 max 0.50 max . . . . . . . . . . . . remainder . . . . . . . . . . . . 1.8-2.4 99.5C49255F 58.0

37、60.0 0.01 max 0.50 max 0.10 max 0.10-0.30 . . . 0.10 max . . . remainder . . . . . . 0.10 max . . . 1.7-2.9 99.5C49260G 58.063.0 0.09 max 0.50 max 0.50 max . . . . . . 0.10 max . . . remainder . . . . . . 0.05- 0.15 . . . 0.50-1.8 99.5C49300H 58.062.0 0.01 max 1.0-1.8 0.10 max 1.5 max 0.50 max 0.10

38、max 0.03 max remainder . . . . . . 0.20 max . . . 0.50-2.0 99.5C49340I 60.063.0 0.09 max 0.50- 1.5 0.12 max . . . . . . 0.10 max . . . remainder . . . . . . 0.05- 0.15 . . . 0.50-2.2 99.5C49350J 61.063.0 0.09 max 1.5-3.0 0.12 max . . . . . . 0.30 max . . . remainder . . . . . . 0.04- 0.15 . . . 0.50

39、-2.5 99.5C49355K 63.069.0 0.09 max 0.50-2.0 0.10 max . . . . . . 1.0-2.0 0.10 max 27.0-35.0 . . . . . . . . . . . . 0.50-1.5 99.5C49360 remainder 0.09 max 1.0-2.0 . . . . . . . . . 2.0-3.5 . . . 19.0-22.0 . . . . . . . . . . . . 0.50-1.5 99.5C61900 remainderA 0.02 max 0.6 max 3.04.5 . . . 8.510.0 .

40、. . . . . 0.8 max . . . . . . . . . . . . . . . 99.5C62300 remainderA . . . 0.6 max 2.04.0 1.0 max 8.510.0 0.25 max 0.50 max . . . . . . . . . . . . . . . . . . 99.5C63000 remainderA . . . 0.20 max 2.04.0 4.05.5 9.011.0 0.25 max 1.5 max 0.30 max . . . . . . . . . . . . . . . 99.5C63200 remainderA 0.

41、02 max . . . 3.54.3L 4.04.8L 8.79.5 0.10 max 1.22.0 . . . . . . . . . . . . . . . . . . 99.5C64200 remainderA 0.05 max 0.20 max 0.30 max 0.25 max 6.37.6 1.52.2 0.10 max 0.50 max . . . . . . . . . 0.09 max . . . 99.5C64210 remainderA 0.05 max 0.20 max 0.30 max 0.25 max 6.37.0 1.52.0 0.10 max 0.50 max

42、 . . . . . . . . . 0.09 max . . . 99.5C65500 remainderA 0.05 max . . . 0.8 max 0.6 max . . . 2.83.8 0.501.3 1.5 max . . . . . . . . . . . . . . . 99.5C67500 57.060.0A 0.20 max 0.501.5 0.82.0 . . . 0.25 max . . . 0.050.50 remainder . . . . . . . . . . . . . . . 99.5C67600 57.060.0A 0.501.0 0.501.5 0.

43、401.3 . . . . . . . . . 0.050.50 remainder . . . . . . . . . . . . . . . 99.5C69150A 82.587.5 0.05 max 0.025 max 0.25 max 0.20 max 0.71.3 0.02 max 0.250.6 remainder . . . . . . . . . . . . . . . 99.6C69300 73.077.0A 0.09 max 0.20 max 0.10 max 0.10 max . . . 2.73.4 0.10 max remainder . . . . . . 0.04

44、0.15 . . . . . . 99.5C70620M 86.5 minA 0.02 max . . . 1.01.8 9.011.0 . . . . . . 1.0 max 0.50 max 0.02 max . . . 0.02 max . . . . . . 99.5C71520M 65.0 minA 0.02 max . . . 0.401.0 29.033.0 . . . . . . 1.0 max 0.50 max 0.02 max . . . 0.02 max . . . . . . 99.5C77400 43.047.0A 0.09 max . . . . . . 9.011

45、.0 . . . . . . . . . remainder . . . . . . . . . . . . . . . 99.5C87700N 87.5 min 0.09 max 2.0 max 0.50 max 0.25 maxO . . . 2.53.5 0.8 max 7.09.0 . . . . . . 0.15 max . . . . . . 99.2C87710N 84 min 0.09 max 2.0 max 0.50 max 0.25 maxO . . . 3.05.0 0.8 max 9.011.0 . . . . . . 0.15 max . . . . . . 99.2

46、A Silver counts as copper.B Includes oxygen-free or deoxidized grades with deoxidizers (such as phosphorus, boron, lithium, or others) in amount agreed upon.C This includes copper + silver + tellurium + phosphorus.D This includes copper + silver + sulfur + phosphorus.E Includes cadmium 0.001 % max.F

47、 Includes cadmium 0.01, selenium 0.02-0.07.G Includes cadmium 0.001 % max.H Includes antimony 0.50 % max and selenium 0.20 % max.I Includes cadmium 0.001 % max.J Includes antimony 0.02-0.10 %.K Includes boron 0.001 % max.L Iron content shall not exceed nickel content.M Carbon shall be 0.05 % max.B12

48、4/B124M134N Antimony shall be 0.10 % max.O Not including Co.B124/B124M13510.1.1.1 For M30 rod, Copper Alloy UNS Nos. C27450, C35330, C36500, C37000, C37700, C46400, C48200, C48500,C48600, C49250, C49255, C49260, C49300, C49340, C49350, C49355, C49360, C61900, C62300, C63000, C63200, C64200,C64210, C

49、67500, C67600, C69150, C69300, C70620, and C71520, refer to Table 4.10.1.1.2 For M30 rod, Copper UNS Nos. C11000, C14500, C14700, C65500, C77400, C87700, and C87710, refer to Table 5.10.1.1.3 For M20, round rod, refer to Table 6.10.1.1.4 For H50 rod, refer to Table 1 for Copper UNS Nos. C11000, C14500, C14700, and Copper Alloy UNS Nos. C46400,C48200, C48500, C49250, C49255, C49260, C49300, C49340, C49350, C49360, and C49360.C69150.10.1.1.5 For H50 rod, refer to Table 2 for Copper Alloy U