ASTM A905-2004(2010) Standard Specification for Steel Wire Pressure Vessel Winding《压力容器缠绕用钢丝的标准规范》.pdf
《ASTM A905-2004(2010) Standard Specification for Steel Wire Pressure Vessel Winding《压力容器缠绕用钢丝的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM A905-2004(2010) Standard Specification for Steel Wire Pressure Vessel Winding《压力容器缠绕用钢丝的标准规范》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: A905 04 (Reapproved 2010)Standard Specification forSteel Wire, Pressure Vessel Winding1This standard is issued under the fixed designation A905; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision
2、. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers requirements for a highstrength drawn and cold rolled steel wire in two strengthclasses, with rectangular
3、 cross section, and round mill edge.This wire is intended for prestressed vessel and press framewindings.1.2 The values stated in either inch-pound units or SI(metric) units are to be regarded separately as standards.Within the text and tables, the SI units are shown in parenthe-ses. The values stat
4、ed in each system are not exact equivalents.Therefore, each system must be used independent of the other.Combining values from the two systems may result in noncon-formance with the specification.2. Referenced Documents2.1 ASTM Standards:2A370 Test Methods and Definitions for Mechanical Testingof St
5、eel ProductsA510 Specification for General Requirements for WireRods and Coarse Round Wire, Carbon SteelA510M Specification for General Requirements for WireRods and Coarse Round Wire, Carbon Steel (Metric)A700 Practices for Packaging, Marking, and Loading Meth-ods for Steel Products for ShipmentE30
6、 Test Methods for Chemical Analysis of Steel, CastIron, Open-Hearth Iron and Wrought Iron3E309 Practice for Eddy-Current Examination of Steel Tu-bular Products Using Magnetic Saturation2.2 Military Standard:MIL-STD-163 Steel Mill Products, Preparation for Ship-ment and Storage42.3 Federal Standard:F
7、ed. Std. No. 123 Marking for Shipment (Civil Agencies)62.4 AIAG Standard:AIAGB-5 02.00 Primary Metals Identification Tag Applica-tion Standard53. Ordering Information3.1 It shall be the responsibility of the purchaser to specifyall requirements that are necessary for material under thisspecification
8、. Such requirements may include, but are notlimited to, the following:3.1.1 Quantity (mass),3.1.2 Name of material,3.1.3 Dimensions (see Section 7),3.1.4 Finish (see Section 8),3.1.5 Packaging (see Section 11),3.1.6 Cast or heat analysis report (see Section 5),3.1.7 Number of certification or test r
9、eports required (seeSection 10),3.1.8 ASTM designation and year of issue, and3.1.9 Supplementary requirements, if any.4. Material and Manufacture4.1 The steel shall be produced by any of the followingprimary processes: (1) basic oxygen, and (2) electric furnace orvacuum induction (VIM). The primary
10、melting may incorpo-rate separate degassing or refining and may be followed bysecondary melting by the electrode slag process (ESR) or thevacuum arc remelting process (VAR).4.1.1 The steel may be ingot cast or continuously cast.4.2 The finished wire shall be free from detrimental pipeand undue segre
11、gation.4.3 The wire shall be cold drawn or cold rolled, or both, toproduce the desired mechanical properties and dimensionsafter subjecting it to the patenting treatment.4.4 The width to thickness ratio of the wire cross sectionshall not exceed 8.5. Chemical Composition5.1 The steel shall conform to
12、 the requirements for chemicalcomposition prescribed in Table 1.5.2 Heat AnalysisEach heat of steel shall be analyzed bythe manufacturer to determine the percentage of elements1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the d
13、irect responsibility of SubcommitteeA01.03 on Steel Rod and Wire.Current edition approved April 1, 2010. Published April 2010. Originallyapproved in 1991. Last previous edition approved in 2004 as A905 04. DOI:10.1520/A0905-04R10.2For referenced ASTM standards, visit the ASTM website, www.astm.org,
14、orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.4Available from Standardization Docu
15、ments Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-50985Available from Automotive Industry Action Group (AIAG), 26200 Lahser Rd.,Suite 200, Southfield, MI 48034.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, Uni
16、ted States.prescribed in Table 1. This analysis shall be made from a testspecimen preferably taken during the pouring of the heat.When requested, this shall be reported to the purchaser andshall conform to the requirements of Table 1.5.3 Product AnalysisAn analysis may be made by thepurchaser from f
17、inished wire representing each heat of steel.The chemical composition thus determined, as to elementsrequired or restricted, shall conform to the product analysisrequirements specified in Table 10 of Specification A510 orA510M.5.4 For referee purposes, Test Methods E30 shall be used.6. Mechanical Re
18、quirements6.1 Tension Test.6.1.1 RequirementsThe material as represented by tensiontest specimens shall conform to the requirements prescribed inTable 2.6.1.2 Number of TestsOne test specimen shall be takenfrom each end of every coil.6.1.3 Test MethodThe tension test shall be made inaccordance with
19、Test Methods and Definitions A370, exceptthat the length L for evaluation of the elongation shall becalculated from the following formula:L 5 11.3=WTwhereW = width of the wire, andT = thickness of the wire.The length L shall be used to calculate the permanentelongation. The distance between the gage
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMA90520042010STANDARDSPECIFICATIONFORSTEELWIREPRESSUREVESSELWINDING 压力容器 缠绕 钢丝 标准规范 PDF

链接地址:http://www.mydoc123.com/p-459926.html