ASME B16 47-2006 Large Diameter Steel Flanges NPS 26 Through NPS 60 Metric Inch Standard (B16 47 - 2006)《大直径钢法兰 NPS 26～NPS 60公制 英制标准》.pdf

《ASME B16 47-2006 Large Diameter Steel Flanges NPS 26 Through NPS 60 Metric Inch Standard (B16 47 - 2006)《大直径钢法兰 NPS 26～NPS 60公制 英制标准》.pdf》由会员分享，可在线阅读，更多相关《ASME B16 47-2006 Large Diameter Steel Flanges NPS 26 Through NPS 60 Metric Inch Standard (B16 47 - 2006)《大直径钢法兰 NPS 26～NPS 60公制 英制标准》.pdf（110页珍藏版）》请在麦多课文档分享上搜索。

1、Large Diameter Steel FlangesNPS 26 Through NPS 60 Metric/Inch StandardAN AMERICAN NATIONAL STANDARDASME B16.47-2006(Revision of ASME B16.47-1996)Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASM

2、E B16.47-2006(Revision of ASME B16.47-1996)Large DiameterSteel FlangesNPS 26 Through NPS 60Metric/Inch StandardAN AMERICAN NATIONAL STANDARDThree Park Avenue New York, NY 10016Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted w

3、ithout license from IHS-,-,-Date of Issuance: May 31, 2007The next edition of this Standard is scheduled for publication in 2011. There will be no addendaissued to this edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of thisStandard. Interpretations a

4、re published on the ASME Web site under the Committee Pages athttp:/cstools.asme.org as they are issued.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStanda

5、rds. The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate. The proposed code or standard was madeavailable for public review and comment that provides an opportunity for additio

6、nal public input from industry, academia,regulatory agencies, and the public-at-large.ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with an

7、yitems mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent, nor assume any such liability. Users of a code or standard are expresslyadvised that determination of the validity of any such patent ri

8、ghts, and the risk of infringement of such rights, isentirely their own responsibility.Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only t

9、hose interpretations of this document issued in accordance with the establishedASME procedures and policies, which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written

10、permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue, New York, NY 10016-5990Copyright 2007 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in the U.S.A.Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo

11、 reproduction or networking permitted without license from IHS-,-,-CONTENTSForeword vCommittee Roster . viCorrespondence With the B16 Committee vii1 Scope . 12 PressureTemperature Ratings 23 Component Size: Nominal Pipe Size . 34 Marking . 35 Materials 36 Dimensions 57 Tolerances . 68 Pressure Testi

12、ng 6Figures1 Welding Ends (Welding Neck Flanges, No Backing Rings) 72 Welding Ends (Welding Neck Flanges With Backing Rings) . 83 Welding Ends (Welding Neck Flanges) . 9Tables1 List of Material Specifications . 102 List of Bolting Specifications (Applicable ASTM Specifications) . 123 PressureTempera

13、ture Ratings for Group 1.1 Materials . 134 PressureTemperature Ratings for Group 1.2 Materials . 145 PressureTemperature Ratings for Group 1.3 Materials . 156 PressureTemperature Ratings for Group 1.4 Materials . 167 PressureTemperature Ratings for Group 1.5 Materials . 178 PressureTemperature Ratin

14、gs for Group 1.7 Materials . 189 PressureTemperature Ratings for Group 1.9 Materials . 1910 PressureTemperature Ratings for Group 1.10 Materials 2011 PressureTemperature Ratings for Group 1.11 Materials 2112 PressureTemperature Ratings for Group 1.13 Materials 2213 PressureTemperature Ratings for Gr

15、oup 1.14 Materials 2314 PressureTemperature Ratings for Group 1.15 Materials 2415 PressureTemperature Ratings for Group 1.17 Materials 2516 PressureTemperature Ratings for Group 2.1 Materials . 2617 PressureTemperature Ratings for Group 2.2 Materials . 2718 PressureTemperature Ratings for Group 2.3

16、Materials . 2819 PressureTemperature Ratings for Group 2.4 Materials . 2920 PressureTemperature Ratings for Group 2.5 Materials . 3021 PressureTemperature Ratings for Group 2.6 Materials . 3122 PressureTemperature Ratings for Group 2.7 Materials . 3223 PressureTemperature Ratings for Group 2.8 Mater

17、ials . 3324 PressureTemperature Ratings for Group 2.9 Materials . 3425 PressureTemperature Ratings for Group 2.10 Materials 3526 PressureTemperature Ratings for Group 2.11 Materials 3627 PressureTemperature Ratings for Group 2.12 Materials 3728 Dimensions of Ring-Joint Facings 3829 Permissible Imper

18、fections in Flange Facing Finish 38iiiCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-30 Dimensions of Class 150 Series A Flanges 3931 Dimensions of Class 300 Series A Flanges 4032 Dimensions of C

19、lass 400 Series A Flanges 4133 Dimensions of Class 600 Series A Flanges 4234 Dimensions of Class 900 Series A Flanges 4335 Dimensions of Class 75 Series B Flanges . 4436 Dimensions of Class 150 Series B Flanges 4537 Dimensions of Class 300 Series B Flanges 4638 Dimensions of Class 400 Series B Flang

20、es 4739 Dimensions of Class 600 Series B Flanges 4840 Dimensions of Class 900 Series B Flanges 4941 Flange Bolting Dimensional Recommendations . 50Mandatory AppendicesI PressureTemperature Ratings and Dimensional Data for Classes 75, 150, 300,400, 600, and 900 Flanges in U.S. Customary Units . 51II

21、Quality System Program 92III References 93Nonmandatory AppendicesA Methods Used for Establishing PressureTemperature Ratings 95B Gaskets (Other Than Ring-Joint) . 99ivCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without li

22、cense from IHS-,-,-FOREWORDIn November 1980, a task force was appointed within Subcommittee C of the American NationalStandards (ANSI) B16 Committee to develop a standard for pipe flanges in size NPS 26 throughNPS 48. Every attempt was made to standardize those dimensions that existed within the ind

23、ustryfor the materials covered by ANSI B16.5.Prompted by suggestions received from committee members, the task force was authorized toincrease the size range to NPS 60. The first draft was developed in December 1982 to includeClass 75 through Class 1500 for the size range NPS 26 through NPS 60. Flan

24、ge dimensions werebased on the Manufacturers Standardization Society Standard Practice (MSS SP) 44 flanges, exceptfor Class 75 flanges that are ANSI/API 605 flanges.At the request of the American Petroleum Institute (API), flange dimensions, in accordancewith the API Standard 605, were included in t

25、he subsequent drafts. Class 1500 flanges weredeleted due to a lack of interest in using large size flanges in that pressuretemperature rating.The API-605 flanges for Class 150 and 300 and for sizes NPS 36 and smaller for classes higherthan Class 300 are not compatible with the MSS SP-44 flanges. Thu

26、s, the MSS SP-44 flanges aredesignated as Series A flanges and the API-605 flanges are designated as Series B flanges in thisStandard. Materials covered in this Standard are as in ANSI B16.5, except nickel base alloys areexcluded. Pressuretemperature ratings are in accordance with ANSI B16.5.In 1982

27、, American National Standards Committee B16 was reorganized as the American Societyof Mechanical Engineers (ASME) B16 Committee operating under procedures accredited by ANSI.Following approval by the Standards Committee and ASME, approval as an American NationalStandard was given by ANSI on June 12,

28、 1990.The 1996 Edition allowed flanges marked with more than one material grade or specification,revised flange face finish requirements, revised pressuretemperature ratings for several materialgroups, added permissible flange facing imperfections, added blind flanges for Series B flanges,and includ

29、ed several other revisions. Following approval by the Standards Committee and ASME,Boiler and Pressure Vessel Committee, ANSI approved the previous edition as an AmericanNational Standard on October 3, 1996 with the new designation ASME B16.47-1996.This 2006 Edition is presented in metric units, as

30、primary units, with U.S. Customary units ineither parenthetical or separate forms. Mandatory Appendix I has been provided after the maintext for convenience to cover ratings and dimensions in U.S. Customary units. Inch dimensionbolt holes were retained for flanges manufactured to metric dimensions t

31、o avoid fit up problems.Development of metric dimensions was done to reflect the intended precision of the dimensionrather than by numerical conversion. For some materials pressuretemperature ratings have beenrevised to reflect revisions to material strength properties (tensile and yield) listed in

32、the ASMEBoiler and Pressure Vessel Code, Section II. Some materials have been assigned to different ratingtables in order to minimize changes to ratings for commonly used materials.All requests for interpretation or suggestions for revisions should be sent to the AdministrativeSecretary B16, The Ame

33、rican Society of Mechanical Engineers, Three Park Avenue, New York, NY10016-5990. As an alternative, inquiries may be submitted via e-mail to: SecretaryB16asme.org.ASME B16.47-2006 was approved by the American National Standards Institute onNovember 6, 2006.vCopyright ASME International Provided by

34、IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASME B16 COMMITTEEStandardization of Valves, Flanges, Fittings, and Gaskets(The following is the roster of the Committee at the time of approval of this Standard.)STANDARDS COMMITTEE OFFICE

35、RSH. R. Sonderegger, ChairM. L. Nayyar, Vice ChairU. DUrso, SecretarySTANDARDS COMMITTEE PERSONNELR. W. Barnes, Anric Enterprises, Inc.W. B. Bedesem, ExxonMobil Research and Engineering Co.D. A. Buccicone, Elkhart Products Corp.M. A. Clark, Nibco, Inc.U. DUrso, The American Society of Mechanical Eng

36、ineersC. E. Floren, Mueller Co.D. R. Frikken, Becht EngineeringG. G. Grills, U.S. Coast GuardM. L. Henderson, Forgital USAG. A. Jolly, Vogt Valves/Flowserve Corp.SUBCOMMITTEE C STEEL FLANGES AND FLANGED FITTINGSM. L. Nayyar, Chair, Bechtel Power Corp.U. DUrso, Secretary, The American Society of Mech

37、anicalEngineersA. Appleton, Alloy Stainless Products Co., Inc.W. B. Bedesem, ExxonMobil Research and Engineering Co.R. Chakravarti, Foster Wheeler USA Corp.C. E. Davila, Crane ValvesB. Dennis, Kerkau ManufacturingJ. P. Ellenberger, WFI InternationalD. R. Frikken, Becht EngineeringM. L. Henderson, Fo

38、rgital USAviM. Katcher, Haynes InternationalW. N. McLean, Newco ValvesT. A. McMahon, Fisher Controls International, Inc.M. L. Nayyar, Bechtel Power Corp.J. D. Page, U.S. Nuclear Regulatory CommissionR. A. Schmidt, Trinity-LadishH. R. Sonderegger, Anvil International, Inc.W. M. Stephan, Flexitallic,

39、L.P.T. F. Stroud, Ductile Iron Pipe Research AssociationD. A. Williams, Southern Company ServicesC. L. Henley, Taylor Forge Engineered Systems, Inc.R. E. Johnson, ConsultantM. Katcher, Haynes InternationalR. Koester, The William Powell Co.W. N. McLean, Newco ValvesW. H. Patrick, The Dow Chemical Co.

40、T. V. Ramakrishnan, Forged Vessel ConnectionsT. C. Rentschler, Solutia Inc.R. A. Schmidt, Trinity-LadishJ. P. Tucker, FlowServeM. M. Zaidi, Jacobs EngineeringCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license fro

41、m IHS-,-,-CORRESPONDENCE WITH THE B16 COMMITTEEGeneral. ASME Standards are developed and maintained with the intent to represent theconsensus of concerned interests. As such, users of this Standard may interact with the Committeeby requesting interpretations, proposing revisions, and attending Commi

42、ttee meetings. Corre-spondence should be addressed to:Secretary, B16 Standards CommitteeThe American Society of Mechanical EngineersThree Park AvenueNew York, NY 10016-5990As an alternative, inquiries may be submitted via e-mail to: SecretaryB16asme.org.Proposing Revisions. Revisions are made period

43、ically to the Standard to incorporate changesthat appear necessary or desirable, as demonstrated by the experience gained from the applicationof the Standard. Approved revisions will be published periodically.The Committee welcomes proposals for revisions to this Standard. Such proposals should beas

44、 specific as possible, citing the paragraph number(s), the proposed wording, and a detaileddescription of the reasons for the proposal, including any pertinent documentation.Interpretations. Upon request, the B16 Committee will render an interpretation of any require-ment of the Standard. Interpreta

45、tions can only be rendered in response to a written request sentto the Secretary of the B16 Standards Committee.The request for interpretation should be clear and unambiguous. It is further recommendedthat the inquirer submit his/her request in the following format:Subject: Cite the applicable parag

46、raph number(s) and the topic of the inquiry.Edition: Cite the applicable edition of the Standard for which the interpretation isbeing requested.Question: Phrase the question as a request for an interpretation of a specific requirementsuitable for general understanding and use, not as a request for a

47、n approvalof a proprietary design or situation. The inquirer may also include any plansor drawings, which are necessary to explain the question; however, theyshould not contain proprietary names or information.Requests that are not in this format will be rewritten in this format by the Committee pri

48、orto being answered, which may inadvertently change the intent of the original request.ASME procedures provide for reconsideration of any interpretation when or if additionalinformation that might affect an interpretation is available. Further, persons aggrieved by aninterpretation may appeal to the

49、 cognizant ASME Committee or Subcommittee. ASME does not“approve,” “certify,” “rate,” or “endorse” any item, construction, proprietary device, or activity.Attending Committee Meetings. The B16 Standards Committee regularly holds meetings, whichare open to the public. Persons wishing to attend any meeting should contact the Secretary ofthe B16 Standard