ARMY MIL-S-51235 C-1989 SMOKE POT FLOATING SGF2 AN-M7A1《AN-M7A1 SGF2浮动发烟罐》.pdf

《ARMY MIL-S-51235 C-1989 SMOKE POT FLOATING SGF2 AN-M7A1《AN-M7A1 SGF2浮动发烟罐》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-51235 C-1989 SMOKE POT FLOATING SGF2 AN-M7A1《AN-M7A1 SGF2浮动发烟罐》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-51235C 13 W 797970b 0333573 2 I a- li O * - C t I INCH-POUND I MIL-S-5 123 5C 8 June 1989 SUPERSEDING 26 January 1988 MIL-S-51235B MILITARY SPECIFICATION SMOKE POT, FLOATING, SGF2, AN-M7Al This specifcation is approved for use by all Departments and Agencies of the Department of Defense. 1. SC

2、OPE 1.1 Scope. This specification covers one type of smoke pot in two conditions. 1.2 Classification. The smoke pot shall be in one of the following conditions as specified (see 6.2): Condition A - With fog oil, fuel block assembly, and fuze Condition B - Without fog oil, fuel block assembly, and fu

3、ze 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, stan- dards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the

4、 issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Co

5、mmander, U.S. Army Chemical Research, Development and Engineering Center, AnN: SMCCR-SPT-S, Aberdeen Proving Ground, MD 2 10 10-5423 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NfA FSC 1365 DISTRlBU

6、TION STATEMENT A. Approved for public release; distribution is unlimited. I THIS DOCUMENT CONTAINS 8 PAGES. -* _ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-51235C SPECIFICATIONS MIL-l3-11522 MIL-I?-11673 - Fuze, Smoke Pot, Floating, Electr

7、ic, M209 MIL-F-12070 - Fog Oil - Fuze, Smoke Pot, M208 and Fuze, Hand Grenade, M226 STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the

8、 Naval Publications and Forms Center, (Am: MODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless ot

9、herwise specified, the issues are those cited in the solicitation. U.S. ARMY CHEMICAL RESEARCH, DEVELOPMENT AND ENGINEERING CENTER DRAWINGS 36-2-212 - Container (Metal Parts Assembly) 36-2-214 - Smoke Pot, Floating, SGF:!, AN-M7A1 . (Copies are available from Commander, U.S. Army Information Systems

10、 Command, Am: ASNC-ARI-IMC-TM, Rock Island, IL 61299-7300.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations

11、 unless a specific exemption has been obtained. 3. REQUIREMENTS * L r 3.1 Materials and components. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L MIL-S-51235C 23 797770b 0333595 b MIL-S-51235C a O I 3.1.1 Materials. All materials cited on Drawi

12、ng 36-2-214 and on the subsidiary drawings shall conform to the specifications listed thereon or to the specific characteris- tics set forth on the drawings. 3.1.2 Components. All components of the smoke pot shall conform to the specifica- tions and drawings listed on Drawing 36-2-214 and on subsidi

13、ary drawings. 3.2 Assembly (see 6.3). 3.2.1 Condition A. The smoke pot shall be assembled and filled as shown on Draw- ing 36-2-214 using fog oil, type SGF2 conforming to MIL-F-12070. 3.2.2 Condition B. The smoke pot shall be assembled as -shown on Drawing 36-2-212. 3.3 Leakage, The smoke pot contai

14、ner (Drawing 36-2-212) with the fuel block as- sembly (Drawing 36-2-219) installed but less the fog oil, outer cover (Drawing 36-2-195) and cover lug (Drawing 36-2-196) shall have a pressure-drop rate no greater than 1 inch of water per minute at a pressure differential of 10.0 k 0.5 inches of mercu

15、ry when tested as specified in 4.2.4.1. . 3.4 Functioning. The smoke pot shall ignite and emit a dense cloud of smoke within a maximum period of 50 seconds. The pot shall continue to emit under pressure a dense cloud of smoke for a period of no less than 8 nor more than 13 minutes without any interr

16、uption greater than 80 seconds, from the time the fuel block begins to burn until the smoke is no longer emitted under pressure when tested as specified in 4.2.4.2. 3.5 Workmanship. The smoke pot shall be free from foreign matter (oil or grease) and damage such as dents, cracks, or deformation which

17、 could affect its use. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or pur- chase order, the contractor is responsible for the performance of all inspection require- ments (examinations and tests) as specified herein. Except as otherwi

18、se specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in

19、this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the

20、 contrac- tors overall inspection system or quality program. The absence of any inspection require- 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-51235C 13 777770b 033357b B MIL-S-51235C ments in the specification shall not relieve the cont

21、ractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with ali requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this

22、does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.1.2 Objective evidence. The contractor shall provide objective evidence acceptable to the contracting officer that the requirements of 3.1 and sect

23、ion 5 for which specific inspection has not been provided in this specification have been satisfied. 4.2 Quality conformance inspection. 4.2.1 Lotting. A lot shall consist of the smoke pots of one interfix number, produced by one manufacturer, at one plant, from the same materials and under essentia

24、lly the same manufacturing conditions. However, no more than one lot of fuzes nor more than one lot of each sustainer or propellant mix ingredients, produced by one manufacturer shall be represented in any one lot of assembled smoke pots. 4.2.2 Sampling. . 4.2.2.1 For examination and nondestructive

25、tests. Sampling shall be conducted in accordance with MIL-STD-105, 4.2.2.2 For functioning tests. Sampling shall be conducted in accordance with table r. TABLE I. Acceptancehejection criteria Lot size Sample size Test paragraph 4.2.4.2 (a) 4.2.4.2 (b) 4.2.4.2 (c) 4.2.4.2 (d) To 1200 32 Accepdreject

26、No. 1 2 1 2 1 2 1 2 1201 to 3200 50 Acceptkeject No. 1 2 1 2 1 2 1 2 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-51235C 13 H 779790b 0333577 T MIL-S-51235C 4.2.3 Inspection. 4.2.3.1. For examination and nondestructive tests. Sample smoke

27、pots and compo- nents shall be examined and tested in accordance with the classification of defects and MIL-STD-105. 4.2.3.2 For functioning tests. The whole sample of smoke pots shall be tested in accordance with 4.2.4.2 including all the characteristics listed in table I (see 6.3). 4.2.3.3 Critica

28、l defects, Each smoke pot in the lot shall be inspected for the critical characteristics listed in the classification of defects. 4.2.3.4 Classification of defects. (a) Smoke pot, floating, SGF2, AN-M7A1 (Drawing 36-2-214) Categories Defects Critical : 1 Fuze safety pin not spread (applicable to M20

29、8 fuze only) Maior: AQL 1.0 percent defective 101 Component missing 102 Component incorrectly assembled 103 Marking incorrect or missing 104 Instruction card missing 105 Workmanship (3.5) (b) Container (Drawing 36-2-212) Categories Defects Critical: None defined Maior: 100 percent inspection 101 Lea

30、kage Maior: AQL 1.0 percent defective Acceptance standards 4.2.4.1 102 Component missing Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-51235C 103 Component incorrectly assembled 104 Fuze adapter thread incorrect 105 Marking missing or incorre

31、ct 106 Cap-plug missing 107 Workmanship (3.5) (c) Fuel block assembly (Drawing 36-2-219) Categories Defects Critical: None defined Maior: AQL 1.0 percent defective 101 Component incorrectly assembled 102 Top surface of fuel block not coated . 103 0.75 diameter hole missing 104 Height of container in

32、correct 105 Diameter (7.85) incorrect 106 Workmanship (3.5) 4.2.4 Tests. 4.2.4.1 Leakage. The smoke pot as described in 3.3 shall be evacuated through both the oil filler opening and the venturi to the specified pressure differential. The vacuum source shall be shut off at the venturi (gage must be

33、between the shut off valve and the venturi) and the oil filler opening (gage must be between the shut off valve and the oil filler opening). The vacuum shall be maintained for a minimum period of 1 minute. The pressure drop shall be measured and recorded. A pressure loss greater than specified shall

34、 be cause for rejection. An independent leakage test shall be performed on each chamber. 4.2.4.2 Functioning. Sample smoke pots or containers filled with SGF2 fog oil con- forming to MIL-F-12070 shall be fuzed with M208 fuzes conforming to MIL-F-11522 or M209 fuzes conforming to MIL-F-11673 and func

35、tioned in water. The depth of the water shall be a minimum of 2 feet. The functioning shall be observed for defects as follows (see 6.3): (a) Failure to ignite or excessive interruption of dense cloud of smoke (b) Excessive delay in emission of dense cloud of smoke (c) Duration of smoke emission les

36、s than the minimum specified (d) Duration of smoke emission greater than the maximum specified 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-51235C 13 7777706 0333577 3 W (This section contains information of a general or explanatory nature

37、, that may be helpful, but is not mandatory.) MIL-S-51235C 5. PACKAGING 5.1 Palletization. The level of palletization shall be as specified (see 6.2). 5.1.1 Level A. Smoke pot assemblies shall be palletized in accordance with Drawing 36-1-119. 5.1.2 Level C. Smoke pot assemblies shall be palletized

38、in accordance with Drawing 36-1-1 19 except pallets shall not be treated with wood-preservative. 5.2 Marking. In conjunction with information furnished in the contract or order, marking shall be as specified in 5.2.1 and 5.2.2. 5.2.1 Smoke pots. Smoke pots shall be marked in accordance with Drawing

39、36-2-214 as applicable to the fuzing and condition type. 5.2.2 Palletized loads. Palletized loads shall be marked in accordance with Drawing 36-1-119 as applicable to the fuzing and condition type. 6. NOTES 6.1 Intended use. The smoke pot is intended for use in producing smoke screens on land or on

40、water. It can be fired manually or by remote control electric current. 6.2 Acquisition requirements. Acquisition documents must specify the following: (a) Title, number, and date of this specification (b) Issue of DODISS to be cited in the solicitation, and if required, the specific (c) Condition of

41、 smoke pot required (see 1.2) (d) If M208 or M209 fuze is required (e) Additional instruction cards to be furnished for the Navy (f) Level of palletization required (see 5.1) issue of individual documents referenced (see 2.1.1) 6.3 Caution. Due to the hazard involved in filling items with flammable

42、mixtures, contractors are advised to exercise all necessary precautions to protect personnel from injury during filling and testing operations. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-S-5L235C 13 7777706 0333600 b -1 MIL-S-51235C 6.4 C

43、omponents specifications: The following specifications reflect the component required for the complete assembly of the smoke pot: MIL-F-11522 - Fuze, Floating Smoke Pot, M208 and Fuze, Hand Grenade, MIL-F-11673 - Fuze, Smoke Pot, Floating, Electric, M209 M226 6.5 Subject term (key word) listing. Fog oil Fuel block assembly Fuze, M208 Fuze, M209 Custodians:, Army - EA Navy - OS I i Preparing activity: Army - EA Project No. 1365-0244 8 hS. GOVERNMENT PRINTING OFFICE: 199 - 6U-033/U9111 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-