ARMY MIL-DTL-41819 21 L-2009 RIBBON ATTACHMENTS NUMERALS ARMY AND MARINE CORPS STRIKE FLIGHT DEVICES NAVY AND MARINE CORPS《勋表附件 陆军和海军陆战队编号 海军和海军陆战部队打击 飞行装备》.pdf

《ARMY MIL-DTL-41819 21 L-2009 RIBBON ATTACHMENTS NUMERALS ARMY AND MARINE CORPS STRIKE FLIGHT DEVICES NAVY AND MARINE CORPS《勋表附件 陆军和海军陆战队编号 海军和海军陆战部队打击 飞行装备》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-41819 21 L-2009 RIBBON ATTACHMENTS NUMERALS ARMY AND MARINE CORPS STRIKE FLIGHT DEVICES NAVY AND MARINE CORPS《勋表附件 陆军和海军陆战队编号 海军和海军陆战部队打击 飞行装备》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A 1 of 2 FSC 8455 INCH-POUND MIL-DTL-41819/21L 1 May 2009 SUPERSEDING MIL-DTL-41819/21K 21 July 2004 DETAIL SPECIFICATION SHEET RIBBON ATTACHMENTS: NUMERALS, ARMY AND MARINE CORPS; STRIKE/FLIGHT DEVICES, NAVY AND MARINE CORPS This specification is approved for use by all Departments and Agen

2、cies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-R-41819. DASH NO. NUMERAL -1, -11 1 -2 -12 2 -3 -13 3 -4 -14 4 -5 -15 5 -6 -16 6 -7 -17 7 -8 -18 8 -9 -19 9 -10 -20 0 MATERIAL: Red Bra

3、ss FINISH: -1 through -10: Oxidized, Relieved, and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 4. -11 through -20: Gold Plated, Matte Finish and shall match TIOH Metal Finish Chip Number 7. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

4、 from IHS-,-,-MIL-DTL-41819/21L 2 of 2 DIMENSIONS: HEIGHT (overall): 3/16 inch (REF) WIDTH (overall): -1, -11: 1/16 inch (REF) -2 through -10, -12 through -20: 11/64 inch (REF) THICKNESS (at thickest point): 0.040 inch + 0.10 inch 0 NOTES: 1. The term (REF) refers to the measurements taken from the

5、Government furnished hub or die. 2. Except for numerals “4“ and “0“, the attaching device shall be a staple type prong located on the horizontal center line of the numeral as close as possible to the vertical center. 3. The attaching device for the numeral “4“ shall be a staple type prong located at

6、 the intersection for the vertical center line of the numeral and the center of the horizontal bar in the numeral. 4. The attaching device for the numeral “0“ shall have two prongs. One prong shall be located at each intersection of the horizontal center line of the numeral and the center of the ver

7、tical arms. 5. The numerals “0“ and “3“ shall be pierced. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodian: Preparing activity: Army - IH Army - IH Navy - NU (Project No. 8

8、455-2009-078) Review activities: Navy - MC DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-