ARMY MIL-DTL-3943 164 B-2010 DECORATION MEDAL OF VALOR BUREAU OF ALCOHOL TOBACCO AND FIREARMS《奖章 酒精 药草和火器局英勇奖章》.pdf

《ARMY MIL-DTL-3943 164 B-2010 DECORATION MEDAL OF VALOR BUREAU OF ALCOHOL TOBACCO AND FIREARMS《奖章 酒精 药草和火器局英勇奖章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3943 164 B-2010 DECORATION MEDAL OF VALOR BUREAU OF ALCOHOL TOBACCO AND FIREARMS《奖章 酒精 药草和火器局英勇奖章》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 2 FSC 8455 DETAIL SPECIFICATION SHEET DECORATION, MEDAL OF VALOR, BUREAU OF ALCOHOL, TOBACCO AND FIREARMS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist

2、of this specification sheet and the latest issue of MIL-DTL-3943. MATERIAL: Red Brass FINISH: 24K Gold Plated, Matte Finish, Polished Highlights and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 8. DIMENSIONS: PENDANT: HEIGHT (to star point): 2-1/16 inches (REF) WIDTH: 1-1/2

3、inches (REF) THICKNESS (at edge): 0.115 inch + 0.010 inch INCH-POUND MIL-DTL-3943/164B 19 February 2010 SUPERSEDING MIL-DTL-3943/164A 1 May 1997 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3943/164B Page 2 of 2 SUSPENSION BAR: HEIGHT (inc

4、luding lug): 1/2 inch (REF) WIDTH: 1-7/16 inches (REF) THICKNESS (at thickest point): 0.100 inch + 0.010 inch NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. The lug for the reverse of the pendant shall be formed into a half circle from brass wi

5、re. The lug shall be fabricated from 0.050 inch + 0.002 inch nominal diameter wire with the same material and finish as the pendant. The lug shall have an outside diameter of 9/32 inch + 1/64 inch and shall be hard soldered to vertical center line of the back of the pendant 3/32 inch from the top on

6、 center. 3. The wires for the suspension bar shall be fabricated from 0.050 inch + 0.002 inch nominal diameter wire with the same material and finish as the suspension bar and hard soldered in the location shown. 4. Decoration set presentation case shall be as specified by the procuring agency. 5. T

7、he ribbon for the pendant drape and service ribbon shall conform to MIL-DTL-11589/382. 6. The lapel button shall conform to MIL-DTL-11484/223. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the

8、 changes. Custodians: Preparing activity: Army - IH Army - IH Review activities: (Project No. 8455-2010-088) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-