AECMA PREN 3315-1996 Aerospace Series Titanium Alloy TI-P64001 Solution Treated and Aged Forgings De Less Than or Equal to 75 mm Issue P 2《航空航天系列.钛合金TI-P64001溶液处理和用于铸造的退火棒材直径D小于或等于.pdf
《AECMA PREN 3315-1996 Aerospace Series Titanium Alloy TI-P64001 Solution Treated and Aged Forgings De Less Than or Equal to 75 mm Issue P 2《航空航天系列.钛合金TI-P64001溶液处理和用于铸造的退火棒材直径D小于或等于.pdf》由会员分享,可在线阅读,更多相关《AECMA PREN 3315-1996 Aerospace Series Titanium Alloy TI-P64001 Solution Treated and Aged Forgings De Less Than or Equal to 75 mm Issue P 2《航空航天系列.钛合金TI-P64001溶液处理和用于铸造的退火棒材直径D小于或等于.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication 1996-05-31 prEN 331 5 Edition P 2 May 1996 C5 Chairman Mr Odorico Comments should be sent within six months after the date of publication to AECMA Gulledelle 94 B-1200 BRUXELLES PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE
2、INDUSTRIES (AECMA) Gulledelle 94 - 8-1200 BRUXELLES - Tel. (32) 2 775 81 10 - Fax. (32) 2 775 81 11 ICs : ENGLISH VERSION Aerospace series Titanium alloy TI-P64001 Solution treated and aged Forgings De I 75 mm Supersedes issue P1 March 1988 Srie arospatiale Alliage de titane TI-P64001 Mis en solutio
3、n et revenu Pices forges et pices matrices De I 75 mrn Luft- und Raumfahrt Titanlegierung TLP6400 1 Lsungsgeglht und ausgelagert Schmiedestcke De 75 mm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is pu
4、blished on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that inter
5、changeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre INPSI and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN
6、 (European Committee for Standardization) for formal vote. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN3315 96 = LOL23LL OOLO438 885 = Pa
7、ge 3 prEN 331 5 : 1996 O Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. This standard has been prepared in accordance with EN 4500-4. 1 Scope This standard specifies the r
8、equirements relating to : Titanium alloy TI-P64001 Solution treated and aged Forgings De I 75 mm for aerospace applications. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the approp
9、riate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publica
10、tion referred to applies. EN 2858-3 Aerospace series - Titanium and titanium alloys - Forging stock and forgings - Technical specification - Part 3 : Pre-production and production forgings EN 3313 Aerospace series - Titanium alloy TI-P64001 - Not heat treated - Grade 2 forging stock, for solution tr
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
2000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AECMAPREN33151996AEROSPACESERIESTITANIUMALLOYTIP64001SOLUTIONTREATEDANDAGEDFORGINGSDELESSTHANOREQUALTO75MMISSUEP2

链接地址:http://www.mydoc123.com/p-420145.html