ABS 61-2017 RULES FOR BUILDING AND CLASSING HIGH-SPEED CRAFT 2017.pdf

《ABS 61-2017 RULES FOR BUILDING AND CLASSING HIGH-SPEED CRAFT 2017.pdf》由会员分享，可在线阅读，更多相关《ABS 61-2017 RULES FOR BUILDING AND CLASSING HIGH-SPEED CRAFT 2017.pdf（710页珍藏版）》请在麦多课文档分享上搜索。

1、 Notices and General Information RULES FOR BUILDING AND CLASSING HIGH-SPEED CRAFT 2017 NOTICES AND GENERAL INFORMATION American Bureau of Shipping Incorporated by Act of Legislature of the State of New York 1862 2016 American Bureau of Shipping. All rights reserved. ABS Plaza 16855 Northchase Drive

2、Houston, TX 77060 USA Table of Contents part Notices and General Information CONTENTS Introduction . 1 TABLE 1 Applicable Editions of Booklets Comprising 2017 Rules 2 TABLE 2 Division and Numbering of Rules and Guides 2 Rule Change Notice (2017) . 3 TABLE 3 Summary of Changes from the 2016 Rules 3 i

3、i ABSRULES FOR BUILDING AND CLASSING HIGH-SPEED CRAFT .2017 Notices and General Information Introduction 1. The year 2017 edition of the Rules for Building and Classing High-Speed Craft consists of the eight (8) booklets as shown in Table 1. With regard to three booklets, Part 1, Part 2, and Part 7:

4、 a) The purpose of the generic title ABS Rules for Conditions of Classification High-Speed Craft (Part 1) is to reflect the expanded contents of PART 1, as a result of including consolidated requirements for “Classification” applicable to all types of and sizes of high-speed craft as specified in th

5、e Foreword to Part 1. Additional specific requirements are contained in Chapters 2 and 3 of Part 1. b) The purpose of the generic title ABS Rules for Materials and Welding of PART 2 is to emphasize the common applicability of the requirements to ABS-classed vessels, other marine structures and their

6、 associated machinery, and thereby make PART 2 more readily a common “PART” of various ABS Rules and Guides, as appropriate. c) The purpose of the generic title ABS Rules for Survey After Construction (Part 7) is to reflect the expanded contents of PART 7, as a result of including consolidated requi

7、rements for “Surveys After Construction” applicable to all types and sizes of vessels, barges and specific shipboard arrangements/systems, etc., as specified in Part 7, Chapter 1, Section 1. 2. The numbering system applied in the Rules is shown in Table 2. 3. The primary changes from the 2016 Rules

8、are identified and listed in Table 3. The effective date of the indicated Rule Changes is 1 January 2017, unless specifically indicated otherwise. 4. The effective date of each technical change since 1993 is shown in parenthesis at the end of the subsection/paragraph titles within the text of each P

9、art. Unless a particular date and month are shown, the years in parentheses refer to the following effective dates: (2000) and after 1 January 2000 (and subsequent years) (1996) 9 May 1996 (1999) 12 May 1999 (1995) 15 May 1995 (1998) 13 May 1998 (1994) 9 May 1994 (1997) 19 May 1997 (1993) 11 May 199

10、3 5. Until the next edition of the Rules for Building and Classing High-Speed Craft is published, Rule Change Notices and/or Corrigenda, as necessary, will be published on the ABS website www.eagle.org only, and will be available free for downloading. It is not intended to publish hard copies of fut

11、ure Rule Change Notices and/or Corrigenda to existing Rules or Guides. The consolidated edition of the Rules for Building and Classing High-Speed Craft, which includes Rule Change Notices and/or Corrigenda using different colors for easy recognition, will be published on the ABS website only when RC

12、N and/or Corrigenda are issued. 6. The listing of CLASSIFICATION SYMBOLS AND NOTATIONS is available from the ABS website www.eagle.org for download. ABSRULES FOR BUILDING AND CLASSING HIGH-SPEED CRAFT .2017 1 Notices and General Information TABLE 1 Applicable Editions of Booklets Comprising 2017 Rul

13、es Notices and General Information 2017 Part 1: Rules for Conditions of Classification High-Speed Craft 2017* Part 2: Rules for Materials and Welding Rules for Testing and Certification of Materials Rules for Welding and Fabrication 2017* Part 2: Rules for Materials and Welding Aluminum and Fiber Re

14、inforced Plastics (FRP) 2017* Part 3: Hull Construction and Equipment 2017 Part 4: Craft Systems and Machinery 2017 Part 5: Specialized Craft and Services 2017 Part 7: Rules for Survey After Construction 2017* * Note: The latest edition of these Rules is to be referred to. These Rules may be downloa

15、ded from the ABS website at www.eagle.org, Rules and Guides, Downloads or may be ordered separately from the ABS Publications online catalog at www.eagle.org, Rules and Guides, Catalog. TABLE 2 Division and Numbering of Rules and Guides Division Number Part Part 1 Chapter Part 1, Chapter 1 Section S

16、ection 1-1-1 Subsection (see Note 1) 1-1-1/1 Paragraph (see Note 1) 1-1-1/1.1 Subparagraph 1-1-1/1.1.1 Item 1-1-1/1.1.1(a) Subitem 1-1-1/1.1.1(a)i) Appendix Appendix 1-1-A1 or Appendix 1-A1-1 Note: 1 An odd number (1, 3, 5, etc.) numbering system is used for the Rules and Guides. The purpose is to p

17、ermit future insertions of even-numbered paragraphs (2, 4, 6, etc.) of text and to avoid the necessity of having to renumber the existing text and associated cross-references, as applicable, within the Rules and associated process instructions, check sheets, etc. 2 ABSRULES FOR BUILDING AND CLASSING

18、 HIGH-SPEED CRAFT .2017 Notices and General Information Rule Change Notice (2017) TABLE 3 Summary of Changes from the 2016 Rules EFFECTIVE DATE 1 July 2016 shown as (1 July 2016) Part/Para. No. Title/Subject Status/Remarks PART 1 Rules for Conditions of Classification High-Speed Craft 1-1-A2/5.5 Pro

19、duct Quality Assurance Certification (PQA) Tier 4 (IACS UR Z26 Alternative Certification Scheme) To incorporate IACS UR Z26, which replaces UR M5 refrigerating, stabilizing, ventilation and air conditioning machinery; and trunk to such spaces, provided they are not handling or using flammable liquid

20、s) are not considered to be high fire risk areas. (Incorporates Notice No. 1) 4-6-5/1.1.3(d) Creepage Distances To align the requirements with the updated IACS UR E11, which aligns with IEC 60502-1 (2009) and IEC 60502-2 (2005) with respect to testing. (Incorporates Notice No. 1) 4-6-5/1.1.3(e) (Ren

21、umbered) Creepage Distances To align the requirements with the updated IACS UR E11, which aligns with IEC 60502-1 (2009) and IEC 60502-2 (2005) with respect to testing. (Incorporates Notice No. 1) 4-6-5/1.1.3(f) (Deleted) Non-standardized Parts To align the requirements with the updated IACS UR E11,

22、 which aligns with IEC 60502-1 (2009) and IEC 60502-2 (2005) with respect to testing. (Incorporates Notice No. 1) 4-6-5/1.9.2(b) Warning Plate To align the requirements with the updated IACS UR E11, which aligns with IEC 60502-1 (2009) and IEC 60502-2 (2005) with respect to testing. (Incorporates No

23、tice No. 1) 4-6-5/1.9.3(h) Cable Test after Installation To align the requirements with the updated IACS UR E11, which aligns with IEC 60502-1 (2009) and IEC 60502-2 (2005) with respect to testing. (Incorporates Notice No. 1) 4-6-5/1.11.2(d) Shutters To align the requirements with the updated IACS U

24、R E11, which aligns with IEC 60502-1 (2009) and IEC 60502-2 (2005) with respect to testing. (Incorporates Notice No. 1) 4-6-5/1.11.2(f) Arc Flash and Associated Installation Requirements To align the requirements with the updated IACS UR E11, which aligns with IEC 60502-1 (2009) and IEC 60502-2 (200

25、5) with respect to testing. (Incorporates Notice No. 1) 4-6-5/1.11.3(a) Application To align the requirements with the updated IACS UR E11, which aligns with IEC 60502-1 (2009) and IEC 60502-2 (2005) with respect to testing. (Incorporates Notice No. 1) 4-6-5/1.13.4 Accessibility To align the require

26、ments with the updated IACS UR E11, which aligns with IEC 60502-1 (2009) and IEC 60502-2 (2005) with respect to testing. (Incorporates Notice No. 1) ABSRULES FOR BUILDING AND CLASSING HIGH-SPEED CRAFT .2017 5 Notices and General Information EFFECTIVE DATE 1 January 2017 shown as (2017) (based on the

27、 contract date for new construction between builder and Owner) Part/Para. No. Title/Subject Status/Remarks PART 3 Hull Construction and Equipment 3-1-2/1.5 Structures Exposed to Low Air Temperatures To clarify material class requirements for plating attached to hull envelope plating exposed to low a

28、ir temperature and to address the relationship between the design temperatures, in line with IACS UR S6. 3-1-2/Table 1 Material Grades To clarify that even if A36 is used it should be produced by a steel mill approved by ABS. 3-1-2/Table 2 Material Class of Structural Members To clarify that even if

29、 A36 is used it should be produced by a steel mill approved by ABS. 3-1-2/Table 3 Application of Material Classes and Grades Structures Exposed at Low Temperatures To clarify material class requirements for plating attached to hull envelope plating exposed to low air temperature and to address the r

30、elationship between the design temperatures, in line with IACS UR S6. 3-1-2/1.7 Design Temperature tD To clarify material class requirements for plating attached to hull envelope plating exposed to low air temperature and to address the relationship between the design temperatures, in line with IACS

31、 UR S6. 3-1-2/Figure 1 Commonly Used Definitions of Temperatures To clarify material class requirements for plating attached to hull envelope plating exposed to low air temperature and to address the relationship between the design temperatures, in line with IACS UR S6. 3-2-7/13 Propulsion Improveme

32、nt Devices (PID) as Hull Appendages To eliminate confusion from the use of “ESD”, which is used elsewhere in the Rules and Guides for “Emergency Shutdown”. 3-2-7/13.7 (New) Structural End Connection To address the risk of cracks developing at the welded end connection of the device to the hull. 3-2-

33、11/1.1 Location and Heights To align the requirements with IACS UI LL14 which says “A guard rail should also be required for first tier deckhouses and for superstructures ends”. 3-2-11/1.5.2 To align the requirements with IACS UI LL47 (g) Fig. 1 and ABS practice. 3-2-A1/3.3.2 Bending Moment at Neck

34、Bearing To specify that in any case that the rudder is not fully submerged in seagoing conditions, rudder stock should also have sufficient strength for such case. 3-3-A1/Table 1 Acceptable Tolerances To clearly indicate the meaning “slash /” in accordance with ABS internal process instructions. 3-6

35、-1/Figure 5 To align with the wording “Main Steering Position” as indicated in 3-6-1/1.1.3. PART 4 Craft Systems and Machinery 4-2-1/3.3 Booster Pumps To emphasize that standby pumps are required for single engine installations, to clarify the required capacity of the specified standby pump, and to

36、avoid the possibility of having a single engine installation with spare pump carried in lieu of a fitted standby pump. 4-2-1/9.3 Low Oil Pressure Alarms, Temperature and Level Indicators To specify that main and auxiliary combustion engines, above 37 kW, must be fitted with an alarm device with audi

37、ble and luminous signals for failure of the lubricating oil system, in line with IACS UR M2. 4-3-3/15.3.1 To allow rudder torque and load to be measured in the ballast condition, and to be reliably extrapolated to the full load condition where the vessel cannot be tested in this condition, in line w

38、ith SOLAS Reg. II-1/29.3 and 29.4. 4-4-1/9.19.3(b) Hose End Fittings To remove the relaxation where flooding can be prevented by the installation of a readily accessible shutoff valve immediately upstream of the hose, and to clarify the requirement for clamps. 4-4-3/9.9.3(b)ix) To provide requiremen

39、ts for side covers, in line with IACS UR P3 Rev 4. 4-5-2/11.1.2 Design To align the requirements with FSS Code Chapter 5, adopted by Resolution MSC.206(81) and amended by Resolution MSC.339(91). 6 ABSRULES FOR BUILDING AND CLASSING HIGH-SPEED CRAFT .2017 Notices and General Information Part/Para. No

40、. Title/Subject Status/Remarks 4-5-2/11.1.3 Alarm To align the requirements with FSS Code Chapter 5, adopted by Resolution MSC.206(81) and amended by Resolution MSC.339(91). 4-5-2/11.4 (New) Clean Agent Fire Extinguishing Systems To align the requirements with the Steel Vessel Rules. 4-5-2/13 Firema

41、ns Outfit To align the requirements for two two-way portable radiotelephone apparatus with SOLAS II-2/Reg.10.4 and the requirements for two (2) spare charges with HSC Code 7.10. 4-6-2/13.3 Navigation Light System To remove inconsistencies and align the requirements with the Steel Vessel Rules. 4-6-2

42、/17.1.2(b) To align the requirements with IACS UI SC35 and MSC.311(88). 4-6-2/17.1.2(c) To clarify that the power supply failure alarms of general emergency alarm system are to be provided in a normally manned control station. 4-6-4/3.21.2(c) Variation from Rated Voltage Transient Conditions To clar

43、ify that voltage regulation during transient conditions need not be tested during factory testing provided that calculated values based on earlier type test records are available, in line with IACS UR E13. 4-6-4/3.21.2(d) Short Circuit Conditions To account for both the stationary short circuit curr

44、ent delivered by the generator, as well as the transient behavior of this short circuit current, in line with IACS UR E13. 4-6-4/10.5.8 Cooling Arrangements To specify the circumstances in which the cooling liquid needs to be non-conducting and non-flammable, in line with IEC 61800-5-1. 4-6-4/10.7.2

45、 Insulation Test (AC or DC Voltage Test) To specify that the duration of the insulation test is 5 sec and 1 sec for the Type Test and the Routine Test, respectively, in line with IEC 61800-5-1. 4-7-1/5.1.22 (New) Data Communication Link To define “data communication link”, in line with IACS UR E22/2

46、.3. 4-7-1/5.3.1 Programmable Electronic System (PES) To define a system based on one or more programmable electronic devices as a Programmable Electronic System, in line with ISO 17894:2005/4.8. 4-7-8/3.1 System Security To clarify system security requirements. ABSRULES FOR BUILDING AND CLASSING HIG

47、H-SPEED CRAFT .2017 7 Part 3 : Hull Construction and equipment RULES FOR BUILDING AND CLASSING HIGH-SPEED CRAFT 2017 PART 3 HULL CONSTRUCTION AND EQUIPMENT American Bureau of Shipping Incorporated by Act of Legislature of the State of New York 1862 2016 American Bureau of Shipping. All rights reserv

48、ed. ABS Plaza 16855 Northchase Drive Houston, TX 77060 USA Rule Change Notice (2017 ) Rule Change Notice (2017) The effective date of each technical change since 1993 is shown in parentheses at the end of the subsection/paragraph titles within the text of each Part. Unless a particular date and mont

49、h are shown, the years in parentheses refer to the following effective dates: (2000) and after 1 January 2000 (and subsequent years) (1996) 9 May 1996 (1999) 12 May 1999 (1995) 15 May 1995 (1998) 13 May 1998 (1994) 9 May 1994 (1997) 19 May 1997 (1993) 11 May 1993 Listing by Effective Dates of Changes from the 2016 Rules Notice No. 1 (effective on 1 July 2016) to the 2016 Rules, which is incorporated in the 2017 Rules, is summarized below. EFFECTIVE DATE 1 July 2016 shown as (1 July 2016) (based on the contract date for new construction between builder and Owner) Pa