ASTM D977-17 Standard Specification for Emulsified Asphalt.pdf

《ASTM D977-17 Standard Specification for Emulsified Asphalt.pdf》由会员分享，可在线阅读，更多相关《ASTM D977-17 Standard Specification for Emulsified Asphalt.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D977 17Standard Specification forEmulsified Asphalt1This standard is issued under the fixed designation D977; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates

2、 the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This specification covers 13 grades of emulsified asphaltfor use in pavement con

3、struction in the manner designated.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in th

4、e Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D5/D5M Test Method for Penetration of Bituminous Mate-rialsD113 Test Method

5、 for Ductility of Bituminous Materials(Withdrawn 2016)3D139 Test Method for Float Test for Bituminous MaterialsD140/D140M Practice for Sampling Asphalt MaterialsD244 Test Methods and Practices for Emulsified AsphaltsD2042 Test Method for Solubility of Asphalt Materials inTrichloroethyleneD3910 Pract

6、ices for Design, Testing, and Construction ofSlurry SealD6930 Test Method for Settlement and Storage Stability ofEmulsified AsphaltsD6933 Test Method for Oversized Particles in EmulsifiedAsphalts (Sieve Test)D6935 Test Method for Determining Cement Mixing ofEmulsified AsphaltD6936 Test Method for De

7、termining Demulsibility of Emul-sified AsphaltD6997 Test Method for Distillation of Emulsified AsphaltD7226 Test Method for Determining the Viscosity of Emul-sified Asphalts Using a Rotational Paddle ViscometerD7496 Test Method for Viscosity of Emulsified Asphalt bySaybolt Furol ViscometerD7553 Test

8、 Method for Solubility of Asphalt Materials inN-Propyl Bromide3. Requirements3.1 The emulsified asphalt shall be tested within 14 days ofdelivery. The emulsified asphalt shall be homogeneous afterthorough mixing provided separation has not been caused byfreezing. Emulsified asphalts separated by fre

9、ezing shall not betested.3.2 Emulsified asphalt shall conform to the requirementsprescribed in Table 1. Specify the test method to be used.Specify either Test Method D7226 or D7496.4. Sampling4.1 Samples of emulsified asphalt shall be taken in accor-dance with Practice D140/D140M.4.2 Samples shall b

10、e stored in clean, airtight sealed contain-ers as specified in Practice D140/D140M at a temperature ofnot less than 4 C until tested.5. Test Methods5.1 The properties of the emulsified asphalts given in Table1 shall be determined in accordance with the following ASTMtest methods:5.1.1 ViscosityTest

11、Method D7496 or D7226.5.1.2 Storage StabilityTest Method D6930.5.1.3 DemulsibilityTest Method D6936.5.1.4 Coating Ability and Water ResistanceTest MethodsD244.5.1.5 Cement MixingTest Method D6935.5.1.6 Sieve TestTest Method D6933.5.1.7 DistillationTest Method D6997.1This specification is under the j

12、urisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.41 onEmulsified Asphalt Specifications.Current edition approved June 1, 2017. Published June 2017. Originallyapproved in 1948. Last previous edition approved in 2014 as D977 131. DOI:10

13、.1520/D0977-17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical

14、standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on

15、Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1TABLE1RequirementsforEmulsifiedAsphaltNOTE1QS-1hemulsionsshallmeettherequirementsoutlinedinPracticesD3910.NOTE2QS-1hisusedforquick-

16、setslurrysealsystems.Rapid-SettingMedium-SettingTypeRS-1RS-2HFRS-2MS-1MS-2MS-2hGrademinmaxminmaxminmaxminmaxminmaxminmaxTestsonEmulsions:Viscosity,SayboltFurolat25CSFS20100.20100100.100.Viscosity,SayboltFurolat50CSFS.7540075400.Viscosity,RotationalPaddleat25C,mPas45220.45220220.220.Viscosity,Rotatio

17、nalPaddleat50C,mPas.165880165880.Demulsibility,35ml,0.02NCaCl2,%60.60.60.Coatingabilityandwaterresistance:Coating,dryaggregate.goodgoodgoodCoating,afterspraying.fairfairfairCoating,wetaggregate.fairfairfairCoating,afterspraying.fairfairfairCementmixingtest,%.Sievetest,%A.0.10.0.10.0.10.0.10.0.10.0.1

18、0Residuebydistillation,%55.63.63.55.65.65.Oildistillatebyvolumeofemulsion,%.TestsonResiduefromDistillationTest:Penetration,25C,100g,5s1002001002001002001002001002004090Ductility,25C,5cm/min,cm40.40.40.40.40.40.Solubilityintrichloroethyleneorn-propylbromide,%97.5.97.5.97.5.97.5.97.5.97.5.Floattest,60

19、Cs.1200.Medium-SettingSlow-SettingQuick-SettingTypeHFMS-1HFMS-2HFMS-2hHFMS-2sSS-1SS-1hQS-1hGrademinmaxminmaxminmaxminmaxminmaxminmaxminmaxTestsonEmulsions:Viscosity,SayboltFurolat25CSFS20100100.100.50.201002010020100Viscosity,SayboltFurolat50CSFS.Viscosity,RotationalPaddleat25C,mPas45220220.220.110.

20、452204522045220Viscosity,RotationalPaddleat50C,mPas.Storagestabilitytest,24-h,%A.1.1.1.1.1.1Demulsibility,35ml,0.02NCaCl2,%.Rapid-SettingMedium-SettingTypeRS-1RS-2HFRS-2MS-1MS-2MS-2hGrademinmaxminmaxminmaxminmaxminmaxminmaxCoatingabilityandwaterresistance:Coating,dryaggregategoodgoodgoodgood.Coating

21、,aftersprayingfairfairfairfair.Coating,wetaggregatefairfairfairfair.Coating,aftersprayingfairfairfairfair.Cementmixingtest,%.2.0.2.0N/ASievetest,%A.0.10.0.10.0.10.0.10.0.10.0.100.10Residuebydistillation,%55.65.65.65.57.57.57Oildistillatebyvolumeofemulsion,%.17.TestsonResiduefromDistillationTest:Pene

22、tration,25C,100g,5s1002001002004090200.10020040904090Ductility,25C,5cm/min,cm40.40.40.40.40.40.40.Solubilityintrichloroethyleneorn-propylbromide%97.5.97.5.97.5.97.5.97.5.97.5.97.5.Floattest,60Cs1200.1200.1200.1200.AThistestrequirementonrepresentativesamplesiswaivedifsuccessfulapplicationofthemateria

23、lhasbeenachievedinthefield.D977 1725.1.8 Tests on Residue from DistillationTest MethodsD244.5.1.8.1 PenetrationTest Method D5/D5M.5.1.8.2 DuctilityTest Method D113.5.1.8.3 SolubilityTest Method D2042 or D7553.5.1.8.4 Float TestTest Method D139.6. Keywords6.1 emulsion; emulsified asphalt; high float;

24、 medium set-ting; rapid setting; slow settingASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, an

25、d the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revisi

26、on of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you sh

27、ouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obt

28、ained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 173