ASTM C1319-17 Standard Specification for Concrete Grid Paving Units.pdf

《ASTM C1319-17 Standard Specification for Concrete Grid Paving Units.pdf》由会员分享，可在线阅读，更多相关《ASTM C1319-17 Standard Specification for Concrete Grid Paving Units.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1319 17Standard Specification forConcrete Grid Paving Units1This standard is issued under the fixed designation C1319; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses

2、 indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers the requirements for concretegrid paving units for vehicular trafficways, parking areas, soilstabilization, and revetments.NOTE 1

3、When particular features are desired, such as weightclassification, higher compressive strength, surface texture, finish, color,or other special features, such properties should be specified separately bythe purchaser. However, local sellers should be consulted as to availabilityof units having the

4、desired features.1.2 The text of this standard references notes and footnoteswhich provide explanatory material. These notes and footnotes(excluding those in tables and figures) shall not be consideredas requirements of the standard.1.3 The values stated in inch-pound units are to be regardedas stan

5、dard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision

6、on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2C33 Specification for Concrete AggregatesC140 Test Methods for Sampling and Testing Co

7、ncreteMasonry Units and Related UnitsC150 Specification for Portland CementC331 Specification for Lightweight Aggregates for ConcreteMasonry UnitsC595 Specification for Blended Hydraulic CementsC618 Specification for Coal Fly Ash and Raw or CalcinedNatural Pozzolan for Use in ConcreteC989 Specificat

8、ion for Slag Cement for Use in Concrete andMortarsC979 Specification for Pigments for Integrally Colored Con-creteC1157 Performance Specification for Hydraulic CementC1232 Terminology of MasonryC1240 Specification for Silica Fume Used in CementitiousMixtures3. Terminology3.1 Terminology defined in T

9、erminology C1232 shall applyfor this specification.4. Materials4.1 Cementitious MaterialsMaterials shall conform to thefollowing applicable ASTM specifications:4.1.1 Portland CementsSpecification C150.4.1.2 Modified Portland CementPortland cement con-forming to Specification C150, modified as follow

10、s:4.1.2.1 Calcium carbonate, with a minimum 85 % CaCO3content, shall be permitted to be interground with the cement,provided the requirements of Specification C150 as modifiedare met: limitation on insoluble residue is 1.5 % and limitationon loss on ignition is 7 %.4.1.3 Blended Hydraulic CementsSpe

11、cification C595.4.1.4 Hydraulic CementSpecification C1157.4.1.5 PozzolansSpecification C618.4.1.6 Blast Furnace Slag CementsSpecification C989.4.1.7 Silica FumeSpecification C1240.4.2 AggregatesAggregates shall conform to one of thefollowing ASTM specifications, except that grading require-ments sha

12、ll not necessarily apply:4.2.1 Normal WeightSpecification C33.4.2.2 LightweightSpecification C331.4.3 Pigments for Integrally Colored ConcreteSpecification C979.4.4 Other ConstituentsAir-entraining agents, integral wa-ter repellents, and other constituents, shall be previouslyestablished as suitable

13、 for use in concrete grid paving units andshall conform to applicable ASTM standards, or they shall beshown by test or experience satisfactory to the specifier and not1This specification is under the jurisdiction of ASTM Committee C15 onManufactured Masonry Units and is the direct responsibility of

14、SubcommitteeC15.03 on Concrete Masonry Units and Related Units.Current edition approved June 1, 2017. Published July 2017. Originally approvedin 1995. Last previous edition approved in 2016 as C1319 16. DOI: 10.1520/C1319-17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcon

15、tact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West

16、Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trad

17、e Organization Technical Barriers to Trade (TBT) Committee.1to be detrimental to the durability of the concrete grid pavingunit or any material customarily used in grid paving construc-tion.5. Physical Requirements5.1 Units shall have maximum length and width dimensionsof 24 in. by 24 in. (610 mm by

18、 610 mm).5.2 Units shall have a minimum specified thickness of 318in. (80 mm).5.3 At the time of delivery to the work site, the units shallconform to the physical requirements prescribed in Table 1.5.4 DurabilityDurability shall be demonstrated by provenfield performance satisfactory to the specifie

19、r that the gridpaver units have adequate durability for the intended use.5.4.1 Proven Field PerformanceSatisfactory field perfor-mance is demonstrated when units similar in composition andmade with the same manufacturing process as those to besupplied to the purchaser, maintain the physical requirem

20、entsspecified in Table 1 after three years of use. The units used asthe basis for proven field performance shall have been exposedto the same general type of environment, temperature range,and traffic volume as is expected for the units supplied to thepurchaser.6. Permissible Variations in Dimension

21、s6.1 Length or width of units shall not differ by more than618 in. (63.2 mm) from specified dimensions. Heights of unitsshall not differ by more than 618 in. (63.2 mm) from thespecified dimensions. Tests shall be performed as required in7.2.7. Sampling and Testing7.1 The purchaser or his authorized

22、representative shall beaccorded proper facilities to inspect and sample the units at theplace of manufacture from lots ready for delivery.7.2 Compressive strength, absorption, density, and dimen-sional tolerances shall be based on tests of concrete grid pavingunits of any configuration or dimensions

23、 made with the samematerials, concrete mix design, manufacturing process, andcuring method, conducted in accordance with Test MethodsC140 and within 12 months of production of the units.8. Visual Inspection8.1 Units shall be free of defects that interfere with theproper placing of the unit or impair

24、 the strength or permanenceof the construction.9. Compliance9.1 If a sample fails to conform to the specifiedrequirements, the manufacturer shall be permitted to removeunits from the shipment. A new sample shall be selected by thepurchaser from remaining units from the shipment with asimilar configu

25、ration and dimension and tested at the expenseof the manufacturer. If the second sample meets the specifiedrequirements, the remaining portion of the shipment repre-sented by the sample meets the specified requirements. If thesecond sample fails to meet the specified requirements, theremaining porti

26、on of the shipment represented by the samplefails to meet the specified requirements.NOTE 2Unless otherwise specified in the purchase order, the costs oftests is typically borne as follows: (1) if the results of the tests show thatthe units do not conform to the requirements of this specification th

27、e costis typically borne by the seller; (2) if the results of the tests show that theunits conform to the specification requirements, the cost is typically borneby the purchaser.10. Keywords10.1 concrete grid paving units; revetments; soil stabiliza-tion; vehicular trafficwaysTABLE 1 Physical Requir

28、ementsCompressive StrengthNet Area,min. psi (MPa)Water Absorption,max lb/ft3(kg/m3)Percent Solid Web Widthin. (mm)Average of 3unitsIndividual Average of 3unitsIndividual Minimum Maximum MinimumAAverageB5000 (35) 4500 (31) 10 (160) 12 (192) 45 75 1.00 (25) 1.25 (32)AMeasured at the thinnest point.BAv

29、erage of measurements along the height of the web.C1319 172SUMMARY OF CHANGESCommittee C15 has identified the location of selected changes to this standard since the last issue(C1319 16) that may impact the use of this standard. (June 1, 2017)(1) Updated Table 1 to clarify percent solid requirements

30、.Committee C15 has identified the location of selected changes to this standard since the last issue(C1319 14) that may impact the use of this standard. (December 1, 2016)(1) Revised Table 1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with

31、 any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible techni

32、cal committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideratio

33、n at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harb

34、or Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 173