ISO 13609-2014 Wood-based panels - Plywood - Blockboards and battenboards《木基板材 胶合板 芯块胶合板和板条胶合板》.pdf
《ISO 13609-2014 Wood-based panels - Plywood - Blockboards and battenboards《木基板材 胶合板 芯块胶合板和板条胶合板》.pdf》由会员分享,可在线阅读,更多相关《ISO 13609-2014 Wood-based panels - Plywood - Blockboards and battenboards《木基板材 胶合板 芯块胶合板和板条胶合板》.pdf(12页珍藏版)》请在麦多课文档分享上搜索。
1、 ISO 2014 Wood-based panels Plywood Blockboards and battenboards Panneaux base de bois Contreplaqus Panneaux latts avec lattes troites et avec lattes larges INTERNATIONAL STANDARD ISO 13609 First edition 2014-02-01 Reference number ISO 13609:2014(E) ISO 13609:2014(E)ii ISO 2014 All rights reserved C
2、OPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written pe
3、rmission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 136
4、09:2014(E) ISO 2014 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 2 4 Material requirement 2 4.1 Requirements for veneer 2 4.2 Requirements for plywood . 2 4.3 Requirements for core strip. 3 4.4 Requirements for core strip assembly
5、4 4.5 Adhesives . 4 5 Panel lay-up and manufacturing requirements . 4 6 General requirements . 4 6.1 Dimensions and tolerances 4 6.2 Classification by surface appearance . 4 6.3 Requirements of physical and mechanical properties 5 7 Bonding quality . 5 8 Formaldehyde release requirements 5 9 Other c
6、haracteristics 5 10 Conformances 5 11 Mar king , identification, and documentation 6 ISO 13609:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normal
7、ly carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the
8、 work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the
9、different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this docume
10、nt may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/
11、patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO pr
12、inciples in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 89, Wood-based panels, Subcommittee SC 3, Plywood.iv ISO 2014 All rights reserved INTERNATIONAL ST ANDARD ISO 13609:2014(E) Wood-based p
13、anels Plywood Blockboards and battenboards 1 Scope This International Standard establishes requirements for the specifications of blockboards and battenboards for general use, in dry, tropic dry/humid, and high-humid/exterior conditions. It includes requirements of materials, lay-up, physical and me
14、chanical properties, bonding quality, formaldehyde release, conformity verification, and marking. The values listed in this International Standard relate to product properties, but they are not characteristic values to be used in design calculations. 2 Normative references The following documents, i
15、n whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC Guide 65, General require
16、ments for bodies operating product certification systems ISO/IEC 17065, Conformity assessment Requirements for bodies certifying products, processes and services ISO 1954, Plywood Tolerances on dimensions ISO 2074, Plywood Vocabulary ISO 2426-2, Plywood Classification by surface appearance Part 2: H
17、ardwood ISO 2426-3, Plywood Classification by surface appearance Part 3: Softwood ISO 9426, Wood-based panels Determination of dimensions of panels ISO 12460-1, Wood-based panels Determination of formaldehyde release Part 1: Formaldehyde emission by the 1-cubic-metre chamber method ISO 12460-3, Wood
18、-based panels Determination of formaldehyde release Part 3: Gas analysis method ISO 12460-4, Wood-based panels Determination of formaldehyde release Part 4: Desiccator method ISO 12465, Plywood Specifications ISO 12466-1, Plywood Bonding quality Part 1: Test methods ISO 12466-2, Plywood Bonding qual
19、ity Part 2: Requirements ISO 16978, Wood-based panels Determination of modulus of elasticity in bending and of bending strength ISO 16979, Wood-based panels Determination of moisture content ISO 16999, Wood-based panels Sampling and cutting of test pieces ISO 18775, Veneers Terms and definitions, de
20、termination of physical characteristics and tolerances ISO 2014 All rights reserved 1 ISO 13609:2014(E) 3 T erms a nd definiti ons For the purposes of this document, the terms and definitions in ISO 2074, ISO 12465, and ISO 18775 and the following apply. 3.1 core strip individual wood pieces with re
21、ctangular cross section which are assembled to form the solid core 4 Material requirement 4.1 Requirements for veneer The following requirements apply to veneer at the time of pressing. 4.1.1 Wood species Any wood species is permitted. Veneers shall be identified according to the species, species gr
22、oup, or mechanical properties. When veneers of different species are used to form a layer, these veneers shall be of similar mechanical and physical properties. 4.1.2 Thickness The thickness (t) of veneer shall be 0,55 mm t 6,0 mm. When veneers are used to cover a core, the thickness of veneers adja
23、cent to the core shall not be less than 1,5 mm. 4.1.3 Surface appearance The surface appearance of veneer shall be controlled. Surface appearance of the face layer shall satisfy the criteria defined for class II, as given in Table 1 in ISO 2426-2 or in Table 1 in ISO 2426-3. Back layer shall not be
24、more than 2 classes inferior to the face layer. If required, veneer classification of other layers shall be carried out in accordance with the limitations defined in Annex A of ISO 12465. 4.1.4 Joint Veneers jointed in width are allowed. If there is a joint in length, it shall be bonded as finger jo
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO136092014WOODBASEDPANELSPLYWOODBLOCKBOARDSANDBATTENBOARDS 板材 胶合板 板条 PDF

链接地址:http://www.mydoc123.com/p-1250797.html