ISO 12574-2-2008 Thermal insulation - Cellulose-fibre loose-fill for horizontal applications in ventilated roof spaces - Part 2 Principal responsibilities of in.pdf

《ISO 12574-2-2008 Thermal insulation - Cellulose-fibre loose-fill for horizontal applications in ventilated roof spaces - Part 2 Principal responsibilities of in.pdf》由会员分享，可在线阅读，更多相关《ISO 12574-2-2008 Thermal insulation - Cellulose-fibre loose-fill for horizontal applications in ventilated roof spaces - Part 2 Principal responsibilities of in.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD ISO 12574-2 First edition 2008-09-15 Reference number ISO 12574-2:2008(E) ISO 2008 Thermal insulation Cellulose-fibre loose-fill for horizontal applications in ventilated roof spaces Part 2: Principal responsibilities of installers Isolation thermique Fibres de cellulose en vr

2、ac pour applications horizontales dans les combles ventiles Partie 2: Principales responsabilits des installateursISO 12574-2:2008(E) ii ISO 2008 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or v

3、iewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability

4、in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitabl

5、e for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utili

6、zed in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax +

7、 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandISO 12574-2:2008(E) ISO 2008 All rights reserved iii Contents Page 1 Scope 1 2 Normative references 1 3 Terms and definitions 1 4 General responsibilities of the installer 3 4.1 Installer training 3 4.2 Documentation ob

8、tained from the manufacturer . 4 4.3 Responsibility for health and safety 4 4.4 Transportation and storage 4 4.5 Verification of material compliance . 4 4.6 Suitability for installation . 4 4.7 Defects prior to installation 5 4.8 Authority having jurisdiction 5 4.9 Installer qualifications on-site 5

9、 4.10 Equipment requirements 5 4.11 Defects in installation . 5 4.12 Documentation by the installer 5 4.13 Maintenance of records 6 5 Specific responsibilities related to performance 6 5.1 Thickness Control of installed thickness . 6 5.2 Coverage Calculation of coverage 6 5.3 Installed number of bag

10、s Calculation . 7 5.4 Surface density Calculation . 7 Annex A (normative) Dispute resolution measurements Measurements for field audits . 9 Annex B (informative) Job-site certificate 10 Annex C (informative) Suitability of the building to receive the insulation product Example of installers checklis

11、t 11 Bibliography . 12ISO 12574-2:2008(E) iv ISO 2008 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO te

12、chnical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates close

13、ly with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft

14、 International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this docume

15、nt may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 12574-2 was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the built environment, Subcommittee SC 3, Thermal insulation products. ISO 12574

16、consists of the following parts, under the general title Thermal insulation Cellulose-fibre loose-fill for horizontal applications in ventilated roof spaces: Part 1: Material specification Part 2: Principal responsibilities of installers Part 3: Test methodsISO 12574-2:2008(E) ISO 2008 All rights re

17、served v Introduction This part of ISO 12574 specifies the principal responsibilities of installers, as these are common in all countries. It does not specify the application procedures or requirements of the installation, which can vary greatly from one construction to another, from one country to

18、another, or from one jurisdiction in a country to another. This part of ISO 12574 does not conflict with local building codes or labour practices. It serves to clearly delineate the principal responsibilities of the manufacturer of the thermal insulation, which are specified in the material specific

19、ation, from the principal responsibilities of the installer listed in this part of ISO 12574. Because of the uniqueness of the concept of principal responsibilities for the installer, the following general definitions in more than one form are given to assist in translation of the term to other lang

20、uages. Specific definitions are given in Clause 3. a) Principal requirements include the following: 1) procedures that are common to all installations regardless of the construction of the building or the country in which the installation occurs; principal requirements can include instructions to ca

21、rry out a policy statement (meet an objective) but it is not necessarily required to provide a linear progression of steps or actions to be taken; 2) document that provides methods used and that are necessary to accomplish the objective of producing a functional installation. b) Responsibility inclu

22、des the following: 1) condition of being accountable for ones actions; accepting responsibility for ones actions means that the individual who commits an act is the one who is required to explain the act and accept any consequences; 2) condition of being obliged to answer, for ones actions, to an au

23、thority that can impose a penalty for failure vi INTERNATIONAL STANDARD ISO 12574-2:2008(E) ISO 2008 All rights reserved 1 Thermal insulation Cellulose-fibre loose-fill for horizontal applications in ventilated roof spaces Part 2: Principal responsibilities of installers 1S c o p e This part of ISO

24、12574 gives the principal responsibilities of the installers of cellulose-fibre loose-fill thermal insulation products for buildings. If a product is manufactured and packaged according to ISO 12574-1 and then installed in ventilated roof spaces as described in ISO 9774, it is expected to provide th

25、e properties declared by the manufacturer. This part of ISO 12574 gives the principal responsibilities of the installer in the installation of the product, in the documentation of the installation and in the declaration that all requirements of this part of ISO 12574 have been met. This part of ISO

26、12574 does not specify fitness of the product for the intended use beyond those aspects relating to installation. Many aspects relating to the fitness for use are specified in government regulations. It is necessary that the installer ensure, when installing the product, that the product installed i

27、s suitable for the application, based on the government regulations and the manufacturers recommendations. The installer can be required to meet ancillary (additional) requirements that are specified in local regulations or the customers requirements. 2 Normative references The following referenced

28、documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7345, Thermal insulation Physical quantities and definitions ISO 9229,

29、 Thermal insulation Vocabulary ISO 12574-1, Thermal insulation Cellulose-fibre loose-fill for horizontal applications in ventilated roof spaces Part 1: Material specification 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 7345, ISO 9229 and the foll

30、owing apply. 3.1 application training training provided by a manufacturer or by a training institute for which certification is providedISO 12574-2:2008(E) 2 ISO 2008 All rights reserved 3.2 roof space loft space attic space enclosed space between the roof and the ceiling 3.3 authority having jurisd

31、iction agency of the government or trade having responsibility for the safe and proper installation of thermal insulation 3.4 blowing wool fibrous insulation material sub-divided into granules or pellets for application or installation by pneumatic equipment ISO 9229 3.5 coverage area provided by a

32、package of loose-fill insulation when applied as per the manufacturers instructions to achieve a declared thermal performance ISO 9229 3.6 designation code shift, production and/or date code used by the manufacturer to identify a particular product lot 3.7 declared thermal resistance thermal resista

33、nce of the insulation declared by the manufacturer for a specific settled thickness, density, and mean temperature NOTE The declared thermal resistance is expressed in units of square metre-kelvin per watt. 3.8 equipment manufacturer organization that manufactures or markets equipment designed to ap

34、ply cellulose-fibre loose-fill thermal insulation 3.9 inspection authority authority that has regulatory responsibility for enforcement 3.10 installed thickness as-blown thickness initial thickness at the time of installation necessary to provide the declared thickness after settlement NOTE 1 See se

35、ttled thickness, 3.18. NOTE 2 The initial thickness is equal to or greater than the declared thickness and it is necessary to take into account any settling after installation. 3.11 installer individual who has application training to install cellulose-fibre loose-fill thermal insulation in roof spa

36、ces, such that it conforms to the labelling on the package and other applicable requirements and regulationsISO 12574-2:2008(E) ISO 2008 All rights reserved 3 3.12 loose-fill system blowing machine and blowing hose required to install cellulose-fibre loose-fill insulation to the specifications given

37、 on the performance chart 3.13 manufacturer organization that manufactures or markets cellulose-fibre loose-fill thermal insulation products and that is responsible for packaging and labelling of the material and specifying the system for application 3.14 performance chart table specifying the insta

38、lled and settled thickness of insulation required to give tabulated values of thermal resistance and maximum area of attic surface covered by each bag 3.15 principal requirement essential procedures that are common to all installations regardless of the construction of the building or the country in

39、 which the installation occurs NOTE Principal requirements may include instructions to carry out a policy statement (meet an objective) but it is not necessarily required to provide a linear progression of steps or actions to be taken. Methods used and methods that are necessary to accomplish the ob

40、jective of a functional installation are normally included. 3.16 R-value thermal resistance of the insulation for a given settled thickness and density NOTE The R-value is expressed in units of square metre-kelvin per watt. 3.17 responsibility condition of being accountable for ones actions, accepti

41、ng responsibility for ones actions, explaining the act, and answering to an authority and accepting any consequences or penalties 3.18 settled thickness thickness declared by the manufacturer such that it meets the requirements of the governing standard 3.19 settlement decrease in the thickness of i

42、nstalled insulation thickness with time NOTE The settlement is expressed as a percentage of the initially installed thickness. 4 General responsibilities of the installer 4.1 Installer training The installer shall ensure that someone present at the site is trained in the following: a) site inspectio

43、n and preparation; b) physical properties of the insulation materials; c) use and maintenance of equipment; d) manufacturers installation requirements; e) verification of the specific requirements in Clause 5; f) material storage and handling;ISO 12574-2:2008(E) 4 ISO 2008 All rights reserved g) ins

44、tallation procedures; h) consumer (site) safety issues; i) local applicable codes and regulations; j) limitations of use; k) related building science; l) record keeping; m) disposal of material waste; n) installer safety. 4.2 Documentation obtained from the manufacturer The installer shall obtain fr

45、om the manufacturer of cellulose-fibre loose-fill thermal insulation, the following information, which shall be printed on the package: a) brand name, name of the manufacturer or supplier and identification of the manufacturing facility location; b) type of insulation and its intended use; c) instru

46、ctions for installation of the product; d) limitations for use of the product; e) coverage chart for the product or the specified maximum area to be covered per package; f) material safety data sheet; g) transportation and storage requirements. 4.3 Responsibility for health and safety The installer

47、shall review related health and safety requirements of the local authority having jurisdiction, requirements of the appropriate regulatory bodies and related application-related recommendations of the manufacturer, and shall conform to the requirements and recommendations. 4.4 Transportation and sto

48、rage The installer shall verify that the transport and storage of insulation products was in accordance with the recommendations of the manufacturer. 4.5 Verification of material compliance The installer shall ensure that the package labels state that the material is in compliance with ISO 12574-1.

49、4.6 Suitability for installation 4.6.1 The installer shall verify that the areas of the building where the product is installed are suitable for the application of the product. The suitability of these areas for the installation is determined from the manufacturers guidelines, the building code, other governmental regulations and the installers training. The installer shall develop a checklist for the installation similar to the example given in Annex C. 4.6