UL 567-2014 UL Standard for Safety Emergency Breakaway Fittings Swivel Connectors and Pipe-Connection Fittings for Petroleum Products and LP-Gas (Tenth Edition Reprint with Revisio.pdf

《UL 567-2014 UL Standard for Safety Emergency Breakaway Fittings Swivel Connectors and Pipe-Connection Fittings for Petroleum Products and LP-Gas (Tenth Edition Reprint with Revisio.pdf》由会员分享，可在线阅读，更多相关《UL 567-2014 UL Standard for Safety Emergency Breakaway Fittings Swivel Connectors and Pipe-Connection Fittings for Petroleum Products and LP-Gas (Tenth Edition Reprint with Revisio.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 567 Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Petroleum Products and LP-GasUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUT

2、ION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Petroleum Products and LP-Gas, UL 567 Tenth Edition, Da

3、ted May 7, 2014 Summary of Topics This new edition of ANSI/UL 567 claries requirements for hose assemblies and revises the Moist Ammonia-Air Stress Cracking Test. The new and/or revised requirements are substantially in accordance with Proposal(s) on this subject dated March 7, 2014. All rights rese

4、rved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or i

5、mplied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of th

6、e use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic

7、versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on

8、the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that ha

9、ve been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. MAY 7, 2014 UL 567 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MAY 7, 2014 UL 567 tr2 No Text

10、on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MAY 7, 2014 1 UL 567 Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe- Connection Fittings for Petroleum Products and LP-Gas The rst through third editions were

11、 titled Pipe Connectors for Flammable Liquids and LP-Gas. The fourth through seventh editions were titled Pipe Connectors for Flammable and Combustible Liquids and LP-Gas. The eighth edition was titled Pipe Connectors for Petroleum Products and LP-Gas. First Edition August, 1959 Second Edition March

12、, 1971 Third Edition August, 1972 Fourth Edition May, 1978 Fifth Edition March, 1984 Sixth Edition March, 1989 Seventh Edition August, 1992 Eighth Edition June, 1996 Ninth Edition July, 2003 Tenth Edition May 7, 2014 This ANSI/UL Standard for Safety consists of the Tenth Edition. The most recent des

13、ignation of ANSI/UL 567 as an American National Standard (ANSI) occurred on May 7, 2014. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL

14、at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all

15、 copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2014 UNDERWRITERS LABORATORIES INC. ANSI/UL 567-2014UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MAY 7, 2014 UL 56

16、7 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 General 4 2.1 Components .4 2.2 Units of measurement .5 2.3 Undated references .5 3 Glossary .5 4 Installation and Operating Instructi

17、ons .6 CONSTRUCTION 5 General 6 6 Materials .7 7 Swivel Connectors And Emergency Breakaway Fittings 7 8 Pipe-Connecting Fittings .8 9 End Connections 9 PERFORMANCE 10 General 12 11 Electrical-Continuity Test 12 12 External Leakage Test 13 13 Seat Leakage Test 14 14 Operation Test .14 15 Endurance Te

18、st 17 16 Abuse Test 17 17 Drop Test 18 18 Hydrostatic-Strength Test 19 19 Pull Test .19 19.1 Pipe-connecting ttings .19 19.2 Emergency breakaway tting 20 20 Tests of Synthetic Rubber Parts 20 20.1 General .20 20.2 Change-in-volume test 21 20.3 Weight-loss test 22 21 Low Temperature Test 22 22 Markin

19、g Adhesion Test 23 23 Moist Ammonia-Air Stress Cracking Test 23 MANUFACTURING AND PRODUCTION TESTS 24 General 24 MARKING 25 General 24 MAY 7, 2014 UL 567 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These require

20、ments cover emergency breakaway ttings, swivel connectors and pipe-connecting ttings of the threadless compression type. Connectors and ttings covered by these requirements are intended only for the following services. 1.2 A swivel connector is either a hose swivel or joint swivel. The swivel connec

21、tor will allow radial movement and shall be constructed for petroleum product, liqueed petroleum gas (LP-Gas) or anhydrous ammonia (NH3) service. 1.3 An emergency breakaway tting is used between the outlet of the dispensing device and the hose nozzle valve or lever-operated fuel transfer valve (LP-G

22、as Service) and separates in the event that the coupling is subjected to an excessive pull force to safeguard against abnormally excessive pull force on the hose assembly and dispenser and prevent loss of liquid. An emergency breakaway tting shall be constructed for petroleum product, liqueed petrol

23、eum gas (LP-Gas) or anhydrous ammonia (NH3) service. The ttings shall be of the single-break or reconnectable type. 1.4 Requirements for the installation and use of dispensing equipment handling petroleum products are included in the Flammable and Combustible Liquids Code, NFPA 30, and the Code for

24、Motor Fuel Dispensing Facilities and Repair Garages, NFPA 30A. 1.5 Requirements for the installation and use of dispensing devices handling LP-Gas are included in the Liqueed Petroleum Gas Code, NFPA 58. 1.6 Requirements for the installation and use of dispensing equipment handling anhydrous ammonia

25、 are included in the Safety Requirements for the Storage and Handling of Anhydrous Ammonia, ANSI/CGA G-2.1 (ANSI K61.1). 1.7 A hose assembly provided with an integral swivel connector for petroleum product service shall comply with the applicable requirements in the Standard for Hose and Hose Assemb

26、lies for Dispensing Flammable Liquids, UL 330. 2 General 2.1 Components 2.1.1 Except as indicated in 2.1.2, a component of a product covered by this standard shall comply with the requirements for that component. 2.1.2 A component is not required to comply with a specic requirement that: a) Involves

27、 a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. MAY 7, 2014 UL 567 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL

28、 2.1.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.1.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certai

29、n temperatures not exceeding specied limits, and shall be used only under those specic conditions. 2.2 Units of measurement 2.2.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 2.3 Undated references 2.3.1 Any undated referenc

30、e to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 3 Glossary 3.1 For the purposes of this standard the following denitions apply: 3.2 FITTING, PIPE-CONNECTING A tting of the threadless compression

31、seal-ring type for use in the assembly of petroleum product dispensing devices to facilitate connection of piping or tubing. These ttings shall be made in the straight coupling style, as well as in the tee, ell, reducer, adapter, and other styles. 3.3 FITTING, RECONNECTABLE TYPE An emergency breakaw

32、ay tting designed such that upon separation it is intended to be reconnected and reused when it is not damaged. 3.4 FITTING, SINGLE-BREAK TYPE An emergency breakaway tting that, upon separation, is not intended to be reconnected and reused. 3.5 HOSE SWIVEL A swivel connector with one end attached to

33、 a hose and the other end to an appurtenance. The hose swivel will allow radial movement of the hose and/or appurtenance to prevent the hose from twisting or having torsional stress. 3.6 LIQUEFIED PETROLEUM GAS (LP-GAS OR LPG) Any material having a vapor pressure not exceeding that allowed for comme

34、rcial propane, as dened in Standard Specication for Liqueed Petroleum (LP) Gases, ASTM D1835, that is composed predominantly of the following hydrocarbons, either by themselves (excluding propylene) or as mixtures: propane, propylene, butane (normal butane or isobutane) and butylenes. 3.7 PETROLEUM

35、PRODUCTS As used herein, means gasoline, gasoline/alcohol blends containing up to 15 percent alcohol, fuel oil, kerosene, and similar liquid motor or heating fuel products. 3.8 PRESSURE INDICATING DEVICE As used herein, the pressure indicating device means one of the following: a) An analog gauge ha

36、ving a pressure range such that the test pressure is between 30 and 70 percent of the maximum scale reading of the gauge; b) A digital pressure transducer, or other digital gauge, that is calibrated over a range of pressure that includes the test pressure; or MAY 7, 2014 UL 567 5UL COPYRIGHTED MATER

37、IAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL c) Other device that is equivalent to the devices in (a) or (b). 3.9 SWIVEL CONNECTOR A type of swivel categorized as either a hose swivel or swivel joint. 3.10 SWIVEL JOINT A swivel connector installed in a pipin

38、g system with at least one end attached to a rigid pipe or other appurtenance that is rmly affixed. The swivel joint will allow radial movement of the pipe or other appurtenance attached to the swivel to prevent torsional stress. 4 Installation and Operating Instructions 4.1 A copy of the installati

39、on and operating instructions shall be provided and shall be used as a guide in the examination and test of the device. For this purpose, a nal printed edition is not required. 4.2 The instructions shall include directions and information as deemed by the manufacturer to be adequate for proper and s

40、afe installation, maintenance and use of the device. 4.3 Each emergency breakaway tting shall be provided with instructions that indicate how to determine that the maximum rated separation force will not damage the hose assembly or dispensing device. 4.4 Each swivel connector shall be provided with

41、instructions that indicates if it is a hose swivel or swivel joint. CONSTRUCTION 5 General 5.1 A connector or tting for use with petroleum products shall be constructed for an operating pressure of not less than 50 pounds per square inch gauge (psig) (340 kPa) for the uid conning portion of the devi

42、ce and 0.5 psig (3.45 kPa) for the vapor conning portion of the device, when provided, and an ultimate rupture pressure of not less than ve times the design pressure. 5.2 A swivel connector or emergency breakaway tting for use with anhydrous ammonia or LP-Gas shall be designed for an operating press

43、ure of not less than 350 psig (2413 kPa) and an ultimate rupture pressure of not less than ve times the design pressure. 5.3 An emergency breakaway tting shall be constructed to separate in the event that the coupling is subjected to a pull force not less than 100 pounds (445 N), and not to exceed 3

44、50 pounds (1557 N) for petroleum product service and 400 pounds (1779 N) for anhydrous ammonia or LP-Gas Service. MAY 7, 2014 UL 567 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 6 Materials 6.1 Materials in contact with the uid to be han

45、dled shall be inherently resistant to being adversely effected by such uid. 6.2 A synthetic rubber part shall not show any signs of cracking or other damage following exposure to minus 40F (minus 40C). See the Low Temperature Test, Section 21. 6.3 A part made of drawn-brass or machined from bass rod

46、 shall be capable of withstanding, without cracking, the Moist Ammonia-Air Stress Cracking Test, Section 23, for copper and copper alloys. 6.4 A copper or a copper-alloy part shall not be used where it is in contact with aluminum, unless one of the parts is coated with chromium or other equivalent m

47、etallic coating to preclude electrolytic action. A coating shall have a thickness of not less than 0.0002 inch (0.0005 mm). 6.5 If atmospheric corrosion of a ferrous material part will interfere with the proper function of a connector or a tting, the part shall be provided with a corrosion-resistant

48、 protective coating. 6.6 A protective coating shall provide resistance against corrosion to a degree not less than that provided by the protective coatings specied in 6.7. 6.7 Cadmium plating shall have a thickness of not less than 0.0003 inch (0.0008 mm) and zinc plating shall have a thickness of n

49、ot less than 0.0005 inch (0.013 mm), except on parts where threads constitute the major portion of the area, in which case the thickness of the cadmium or the zinc plating shall not be less than 0.00015 inch (0.0038 mm). 6.8 Ammonia containing minute quantities of water reacts rapidly with cadmium, copper, zinc, and many alloys, especially those of copper base. Only iron, steel, and certain nonferrous alloys, determined to be satisfactory for ammonia service, ar