SAE AS 9489D-2015 BOLT MACHINE - HEXAGON HEAD FULL SHANK CORROSION AND HEAT RESISTANT STEEL UNS S66286 130 KSI MIN 1900-32 UNJF-3A.pdf

《SAE AS 9489D-2015 BOLT MACHINE - HEXAGON HEAD FULL SHANK CORROSION AND HEAT RESISTANT STEEL UNS S66286 130 KSI MIN 1900-32 UNJF-3A.pdf》由会员分享，可在线阅读，更多相关《SAE AS 9489D-2015 BOLT MACHINE - HEXAGON HEAD FULL SHANK CORROSION AND HEAT RESISTANT STEEL UNS S66286 130 KSI MIN 1900-32 UNJF-3A.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDBOLT, MACHINE - HEXAGON HEAD, FULL, SHANK,CORROSION AND HEAT RESISTANT STEEL,UNS S66286, 130 KSI MIN, .1900-32 UNJF-3AAS9489Copyright 2015 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form o

2、r by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www

3、.sae.orgISSUED1999-12 STABILIZED2012-01 REVISED 2015-12THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV.DFEDERAL SUPPLY CLASS5306AS9489SHEET 1 OF 2REV.DPROCUREMENT SPECIFICATION: AS7477SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering science

4、s. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for anyparticularuse, includingany patent infringement arising therefrom,isthe soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancel

5、led.SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9489DRATIONALEPART NUMBER MA9489-14 CORRECTED TO READ AS9489-14, AS9489-30 MASS CORRECTED TO READ 2.20.NOTICETHE INITIAL SAE PUB

6、LICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM THE U.S. MILITARY STANDARD MS9489A, AMENDMENT 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THEORIGINAL MILITARY DOCUMENT.ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRAC

7、TS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT.FIGURE 1 - BOLTAEROSPACE STANDARDAS9489SHEET 2 OF 2REV.DBOLT, MACHINE - HEXAGON HEAD, FULL, SHANK,CORROSION AND HEAT RESISTANT STEEL,UNS S66286, 130 KSI MIN, .1900-32 UNJF-3ATAB

8、LE 1 - PART NUMBERS AND DIMENSIONSPART NUMBER L KAPPROX MASSLB/100PART NUMBR L KAPPROXMASSLB/100MS9489-04 .365 - .385 .072 - .092 .72 MS9489-25 1.678 - 1.698 .998 - 1.058 1.76MS9489-05 .428 - .448 .072 - .092 .77 MS9489-26 1.740 - 1.760 1.060 - 1.120 1.81MS9489-06 .490 - .510 .072 - .092 .82 MS9489-

9、27 1.865 - 1.885 1.185 - 1.245 1.91MS9489-07 .552 - .572 .072 - .092 .87 MS9489-28 1.990 - 2.010 1.310 - 1.370 2.01MS9489-08 .615 - .635 .072 - .092 .92 MS9489-29 2.115 - 2.135 1.435 - 1.495 2.11MS9489-09 .678 - .698 .072 - .092 .97 MS9489-30 2.240 - 2.260 1.560 - 1.620 2.20MS9489-10 .740 - .760 .07

10、2 - .120 1.02 MS9489-31 2.365 - 2.385 1.685 - 1.745 2.30MS9489-11 .802 - .822 .122 - .182 1.07 MS9489-32 2.490 - 2.510 1.810 - 1.870 2.40MS9489-12 .865 - .885 .185 - .245 1.12 MS9489-33 2.615 - 2.635 1.935 - 1.995 2.50MS9489-13 .928 - .948 .245 - .308 1.17 MS9489-34 2.740 - 2.760 2.060 - 2.120 2.60M

11、S9489-14 .990 - 1.010 .310 - .370 1.22 MS9489-35 2.865 - 2.885 2.185 - 2.245 2.70MS9489-15 1.052 - 1.072 .372 - .432 1.27 MS9489-36 2.990 - 3.010. 2.310 - 2.370 2.80MS9489-16 1.115 - 1.135 .435 - .495 1.32 MS9489-37 3.115 - 3.135 2.435 - 2.495 2.89MS9489-17 1.178 - 1.198 .498 - .558 1.37 MS9489-38 3

12、.240 - 3.260 2.560 - 2.620 2.99MS9489-18 1.240 - 1.260 .560 - .620 1.41 MS9489-39 3.365 - 3.385 2.685 - 2.745 3.09MS9489-19 1.302 - 1.322 .622 - .682 1.46 MS9489-40 3.490 - 3.510 2.810 - 2.870 3.19MS9489-20 1.365 - 1.385 .685 - .745 1.51 MS9489-41 3.615 - 3.635 2.935 - 2.995 3.29MS9489-21 1.428 - 1.

13、448 .748 - .808 1.56 MS9489-42 3.740 - 3.760 3.060 - 3.120 3.39MS9489-22 1.490 - 1.510 .810 - .870 1.61 MS9489-43 3.865 - 3.885 3.185 - 3.245 3.49MS9489-23 1.552 - 1.572 .872 - .932 1.66 MS9489-44 1.802 - 1.822 1.122 - 1.182 1.86MS9489-24 1.615 - 1.635 .935 - .995 1.71 MS9489-45 1.928 - 1.948 1.248

14、- 1.308 1.98NOTES:1. FOR PARTS NUMBERED MS9489-04 THRU MS9489-14 THE THREAD PD DATUM Z SHALL REPLACE DATUM Y.2. MATERIAL: CORROSION AND HEAT RESISTANT STEEL PER AMS5731 (UNS S66286).3. PROCUREMENT SPECIFICATION: AS7477.4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417.5. SURFACE TEXTURE: SYMBOLS PE

15、R ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra.6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED.7. DIMENSIONS ARE IN INCHES.8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5-1982 (ASME PUIBLICATION).9. THREADS PER AS887910. DO NOT

16、 USE UNASSIGNED PART NUMBERS.11. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPL

17、ETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.