SAE AS 5960B-2013 Hose Assembly Polytetrafluoroethylene Metallic Braid Reinforced 5080 psi (35 000 kPa) 400 (204 Aircraft Hydraulic Systems《航空器液压系统用400℉(204℃)、5080 psi(35000 kPa)金属编织物加固的聚四.pdf

《SAE AS 5960B-2013 Hose Assembly Polytetrafluoroethylene Metallic Braid Reinforced 5080 psi (35 000 kPa) 400 (204 Aircraft Hydraulic Systems《航空器液压系统用400℉(204℃)、5080 psi(35000 kPa)金属编织物加固的聚四.pdf》由会员分享，可在线阅读，更多相关《SAE AS 5960B-2013 Hose Assembly Polytetrafluoroethylene Metallic Braid Reinforced 5080 psi (35 000 kPa) 400 (204 Aircraft Hydraulic Systems《航空器液压系统用400℉(204℃)、5080 psi(35000 kPa)金属编织物加固的聚四.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS5960BAEROSPACESTANDARDAS5960 REV. B Issued 2004-07 Revised 2013-03 Superseding AS5960A Hose A

5、ssembly, Polytetrafluoroethylene, Metallic Braid Reinforced, 5080 psi (35 000 kPa), 400 F (204 C), Aircraft Hydraulic Systems RATIONALEAdded periodic testing requirements for fire resistant hose assemblies. Relocated fire test qualification requirements from NOTES paragraph 6.1.1 to qualification te

6、sting paragraphs 3.5.2.15 and 4.6.16. 1. SCOPE This document defines the requirements for polytetrafluoroethylene (PTFE) lined, metallic braid reinforced, hose assembly suitable for use in 400 F (204 C), 5080 psi (35 000 kPa) aircraft hydraulic systems. NOTE: The SI metric units defined herein are s

7、oft conversion units. 2. APPLICABLE DOCUMENTS The following publications form a part of this document to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue of other publications shall be the issue in effect on the date of the purchase order. In the ev

8、ent of conflict between the text of this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 2.1.1 SAE Publications Available from SAE Internatio

9、nal, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AS478 Identification Marking Methods AS603 Impulse Testing of Hydraulic Hose, Tubing, and Fitting Assemblies AS611 Hose Assembly and Tubing, Polytetrafluoroeth

10、ylene, Cleaning Methods for ARP908 Torque Requirements, Installation and Qualification Test, Hose and Tube Fitting AS1055 Fire Testing of Flexible Hose, Tube Assemblies, Coils, Fittings, and Similar System Components SAE AS5960B Page 2 of 27 AS1072 Sleeve, Hose Assembly, Fire Protection AIR1228 Stan

11、dard Impulse Machine Equipment and Operation ARP1835 Preparation for Delivery, General Requirements for Hose Assemblies AS2078 Test Methods, Hose Assemblies, Polytetrafluoroethylene (PTFE) AS4207 Fitting End, External Thread, Beam Seal, Design Standard ARP4266 Hole Contour, Fluid Passage, Tube Fitti

12、ng AS5272 Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting, Procurement Specification AS5685 Steel, Corrosion Resistant, Safety Wire, 18Cr - 11.5Ni (UNS S30500) Solution Heat Treated, Cold FinishedAS5827 Fitting End, Flareless, Extra Fine Thread, Design Standard AS7003 Nadcap Program Requirem

13、ents AS8879 Screw Threads - UNJ Profile, Inch, Controlled Radius Root with Increased Minor Diameter AS85720 Fittings, Tube, Fluid Systems, Separable, High Pressure, Dynamic Beam Seal, General Specification forAS85720/1 Fittings, Tube, Fluid Systems, Separable, High Pressure, Dynamic Beam Seal, Desig

14、n Standard for Male End AMS2486 Conversion Coating of Titanium Alloys, Fluoride-Phosphate Type AMS2487 Anodic Treatment of Titanium and Titanium Alloys, Solution pH 12.4 Maximum AMS2700 Passivation of Corrosion Resistant Steels AMS4928 Titanium Alloy, Bars, Wire, Forgings, Rings, and Drawn Shapes, 6

15、Al - 4V, Annealed AMS4965 Titanium Alloy, Bars, Wire, Forgings, and Rings, 6.0Al - 4.0V, Solution Heat Treated and Aged AMS5637 Steel, Corrosion Resistant, Bars and Wire, 18Cr - 9.0Ni (SAE 30302) Solution Heated Treated, Cold Drawn and Stress Relieved, 125 ksi (862 MPa) Tensile Strength AMS5639 Stee

16、l, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, and Rings, 19Cr - 10Ni, Solution Heat TreatedAMS5645 Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings, 18Cr - 10Ni - 0.40Ti (321), Solution Heat Treated AMS5646 Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings

17、, Tubing, and Rings, 18Cr - 11Ni - 0.60Cb(Nb) (347), Solution Heat Treated AMS5647 Steel, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, and Rings, 19Cr - 9.5Ni, Solution Heat TreatedSAE AS5960B Page 3 of 27 AMS5656 Steel, Corrosion Resistant, Bars, Wire, Forgings, Extrusions, and Rings, 9.0Mn -

18、 20Cr - 6.5Ni - 0.27N Solution Heat Treated AMS5659 Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions, 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu, Consumable Remelted, Precipitation Hardenable AMS5666 Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, Extrusions, and Rings, 62

19、Ni - 21.5Cr - 9.0Mo - 3.65 (Cb Nb+Ta), Annealed AMS5688 Steel, Corrosion-Resistant, Wire, 18Cr - 9.0Ni (SAE 30302), Spring Temper AMS5689 Steel, Corrosion and Heat Resistant, Wire, 18Cr - 10.5Ni - 0.40Ti (SAE 30321), Solution Heat TreatedAMS5690 Steel, Corrosion and Heat Resistant, Wire, 17Cr - 12Ni

20、 - 2.5Mo (SAE 30316), Solution Heat Treated AMS5697 Steel, Corrosion-Resistant, Wire, 19Cr - 9.5Ni (SAE 30304), Solution Heat Treated AMS5731 Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings, 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V, Consumable Electrode Melted, 180

21、0 F (982 C) Solution Heat Treated AMS5732 Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings, 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V, Consumable Electrode Melted, 1800 F (982 C) Solution and Precipitation Heat Treated AMS5734 Steel, Corrosion and Heat-Resistant, Bar

22、s, Wire, Forgings, and Tubing, 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V, Consumable Electrode Melted, 1650 F (899 C) Solution Heat Treated AMS5737 Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, and Tubing, 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V, Consumable Electrode Melted,

23、 1650 F (899 C) Solution and Precipitation Heat TreatedAMS-QQ-P-35 Passivation Treatments for Corrosion-Resistant Steels2.1.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM A 262 Detect

24、ing Susceptibility to Intergranular Attack on Stainless Steel ASTM A 313 Standard Specification for Stainless Steel Spring Wire ASTM B 348 Specification for Titanium and Titanium Alloy Bars and Billets, Grade 2 ASTM A 580 Specification for Stainless and Heat Resistant Steel Wire SAE AS5960B Page 4 o

25、f 27 2.1.3 U.S. Government Publications Available from the Document Automation and Production Service (DAPS), Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, Tel: 215-697-6257, http:/assist.daps.dla.mil/quicksearch/.MIL-PRF-680 Dry Cleaning Solvent MIL-PRF-5606 Hydraulic Fluid, Petrol

26、eum Base, Aircraft, Missile, and Ordinance MIL-HDBK-831 Preparation of Test Reports MIL-PRF-83282 Hydraulic Fluid, Fire-Resistant, Synthetic, Hydrocarbon Base, Aircraft MIL-PRF-87257 Hydraulic Fluid, Fire Resistant, Low Temperature, Synthetic Hydrocarbon Base, Aircraft and Missile 2.1.4 NAS Publicat

27、ions Available from Aerospace Industries Association, 1000 Wilson Boulevard, Suite 1700, Arlington, VA 22209-3928, Tel: 703-358-1000, www.aia-aerospace.org.NAS 847 Caps and Plugs, Protective, Dust and Moisture Seal NAS 1760 Fitting End, Flareless Acorn, Standard Dimensions for 2.1.5 ASME Publication

28、s Available from American Society of Mechanical Engineers, 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900, Tel: 973-882-1170, www.asme.org.ASME B46.1 Surface Texture ASME Y14.100 Engineering Drawing Practices 2.1.6 PRI Publications Available from Performance Review Institute, 161 Thorn Hill R

29、oad, Warrendale, PA 15086-7527, Tel: 724-772-1616, www.pri-network.org.AC7112 National Aerospace and Defense Contractors Accreditation Program Requirements for Fluid System ComponentsPD2001 Qualified Product Management Council Procedures for Qualified Products Group PD2101 Aerospace Quality Assuranc

30、e, Product Standard, Qualification Procedures, Fluid Systems 2.1.7 RTCA Publications Available from Radio Technical Commission for Aeronautics Inc., 1828 L Street, NW, Suite 805, Washington, DC 20036, Tel: 202-833-9339, www.rtca.org.DO-160 Environmental Conditions and Test Procedures for Airborne Eq

31、uipment SAE AS5960B Page 5 of 27 3. TECHNICAL REQUIREMENTS 3.1 Qualification Hose assemblies supplied in accordance with this document shall be representative of products which have been subjected to and which have successfully passed the qualification tests specified in this performance specificati

32、on. 3.1.1 Manufacturer Qualification A manufacturer producing a product in conformance to this performance specification shall be accredited in accordance with the requirements of PD2101, AS7003 and AC7112, and shall be listed in a Performance Review Institute (PRI) Qualified Manufacturers List (QML

33、). 3.1.2 Product Qualification All products shall conform to the requirements of this procurement specification and shall be approved in accordance with the requirements of PD2001, and PD2101, for listing in a Performance Review Institute (PRI) Qualified Parts List (QPL). When this performance speci

34、fication is specified on design activity controlled drawings, the approved source of supply shall be defined by the design activity. 3.2 Materials The hose assembly materials shall be uniform in quality, free from defects, consistent with good manufacturing practice, and shall conform to applicable

35、specifications and the requirements specified herein. 3.2.1 Metals Metals used in the hose and fittings shall be corrosion resistant steel, nickel alloy, or titanium and shall conform to the following specifications: 3.2.1.1 Bars and Forgings (1) AMS4928 6Al-4V Titanium - Annealed (2) AMS4965 6Al-4V

36、 Titanium - Solution Treated (3) AMS5637 302 CRES (4) AMS5639 304 CRES (5) AMS5645 321 CRES (6) AMS5646 347 CRES (7) AMS5647 304L CRES (8) AMS5656 21-6-9 CRES (9) AMS5659 15-5PH Solution Treated (10) AMS5666 Nickel Alloy type 625 (11) AMS5731 A286 Solution Heat Treated SAE AS5960B Page 6 of 27 (12)

37、AMS5732 A286 Solution and Precipitation Heat Treated (13) AMS5734 A286 Solution Heat Treated (14) AMS5737 A286 Solution and Precipitation Heat Treated (15) ASTM B 348 Grade 2 Titanium Alloy 3.2.1.2 Wire (1) ASTM A 580/313 Comp. 302 (AMS 5688) (2) ASTM A 580/313 Comp. 304 (AMS 5697) (3) ASTM A 580/31

38、3 Comp. 316 (AMS 5690) (4) ASTM A 580/313 Comp. 321 (AMS 5689) (5) AS5685 305 CRES 3.3 Design and Construction The hose assembly shall consist of a seamless PTFE inner tube, corrosion resistant steel wire reinforcement, and corrosion-resistant steel, nickel alloy, and/or titanium end fittings, as re

39、quired, to meet the construction and performance requirements of this document. 3.3.1 Inner Tube The inner tube shall be of a seamless construction of virgin PTFE resin of uniform gage. It shall have a smooth bore and shall be free from pitting or projections on the inner surface. Additives may be i

40、ncluded in the compound from which the tube is extruded. 3.3.2 Reinforcement The reinforcement shall consist of corrosion resistant braid(s) and/or wraps conforming to the applicable material specification listed in 3.2.1.2. The reinforcement shall be arranged over the inner tube to provide sufficie

41、nt strength and protection for ensuring conformance to the requirements specified herein. Broken reinforcing wires shall be cause for rejection. Crossed-over reinforcing wires shall not be cause for rejection of the hose assembly. 3.3.3 Interlayers Interlayers, if used, shall be of a suitable materi

42、al and shall be resistant to pressure pounding and to all fluids with which the hose may come in contact during normal service. They shall be capable of withstanding temperatures of -65 to 400 F (-54 to 204 C) and shall not extrude through the outer braid during testing or in service. 3.3.4 Fittings

43、 All fittings shall be permanently attached and proven to meet the requirements herein. Standard hose assemblies shall have flareless fittings according to NAS 1760, AS4458, or equivalent, to mate with AS5827, or dynamic beam seal fittings to mate with male end per AS85720/1 or AS4207. Anti-torque h

44、exes or flats shall be provided and shall fit standard wrench openings. All internal surfaces of fitting nuts and retaining wire, when used, shall be dry filmed with dry film per AS5272. Dry film on external surfaces and overspray is not cause for rejection. SAE AS5960B Page 7 of 27 3.3.4.1 Straight

45、 and Standard Shaped Fittings Straight fittings shall be machined and standard shapes shall be machined or forged. For elbow fittings, the inside diameter corner shall be a radius in accordance with ARP4266. 3.3.4.2 End Fitting Collars (Sockets) All end fitting collars (sockets), crimped or swaged,

46、and fabricated from Type 304 stainless steel are required to be capable of passing an embrittlement test as specified in ASTM A 262 Practice E, prior to assembly to the nipple and crimp or swaging operation. Sockets fabricated from stabilized austenitic steel (304L, 321, or 347) and titanium are acc

47、eptable without being subjected to the embrittlement test. Titanium collars, if used, shall be per ASTM B 348 - Grade 2. 3.3.5 Finish 3.3.5.1 Corrosion Resistant Steel Fittings Unless otherwise specified, corrosion resistant steel fittings shall be passivated in accordance with AMS2700 or AMS-QQ-P-3

48、5.3.3.5.2 Titanium Alloy Fittings Unless otherwise specified, titanium alloy fittings shall be fluoride phosphate coated per AMS2486 or titanium anodized per AMS2487. 3.4 Dimensions The hose assembly dimensions, except for length, shall be as specified in Figure 1 and Tables 1A or 1B. 3.4.1 Hose Wei

49、ght Hose consisting of inner tube, reinforcement, and interlayers, as outlined in 3.3.1 through 3.3.3 shall not exceed the maximum hose weights specified in Table 2. 3.5 Performance The inner tube and hose assembly shall meet the following performance requirements: 3.5.1 Inner Tube 3.5.1.1 Tube Roll The tube shall not leak, split, burst, or show any evidence of malfunction, when rolled to the flattening and rounding gaps of AS