SAE AS 1715E-2008 WASHER COUPLING FLEXIBLE VARIABLE CAVITY THREADED FERRULE TYPE TUBE ENDS《套圈型管端螺纹可变空腔谐振器柔性耦合垫圈》.pdf

《SAE AS 1715E-2008 WASHER COUPLING FLEXIBLE VARIABLE CAVITY THREADED FERRULE TYPE TUBE ENDS《套圈型管端螺纹可变空腔谐振器柔性耦合垫圈》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 1715E-2008 WASHER COUPLING FLEXIBLE VARIABLE CAVITY THREADED FERRULE TYPE TUBE ENDS《套圈型管端螺纹可变空腔谐振器柔性耦合垫圈》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD WASHER, COUPLING, FLEXIBLE, VARIABLE CAVITY, THREADED, FERRULE TYPE TUBE ENDS AS1715Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanica

2、l, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1982-05REVISED2008-0

3、8REAFFIRMED2014-11THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3A REV.E FEDERAL SUPPLY CLASS 4730 SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability fo

4、r any particularuse, includingany patentinfringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled. SAEinvites yourwritten comments andsuggestions.RATIONALE AS1715E HAS BEEN REAF

5、FIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. AS1715 SHEET 1 OF 3 REV. E PROCUREMENT SPECIFICATION: /4/ AS1710 SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS1715E FIGURE 1 - WASHER AEROSPACE STANDARD AS1715 SHEET 2

6、OF 3 REV. E WASHER, COUPLING, FLEXIBLE, VARIABLE CAVITY, THREADED, FERRULE TYPE TUBE ENDS TABLE 1 - COUPLING WASHER DIMENSIONS AND WEIGHTS BASIC NO. AS1715 SIZE CODE (TUBE SIZE) A +.000/-.008B .004 C-GAGE +.0000/-.0002 MATERIAL WEIGHT LB/EA APPROX. REF. -08 .500 .054 .082 .7990 ALUMINUM .001 -10 .62

7、5 .054 .082 .9240 ALUMINUM .002 -12 .750 .054 .115 1.1340 ALUMINUM .003 -16 1.000 .054 .119 1.3940 ALUMINUM .003 -20 1.250 .054 .119 1.6440 ALUMINUM .003 -24 1.500 .054 .176 2.0130 ALUMINUM .005 -28 1.750 .054 .176 2.2630 ALUMINUM .006 -32 2.000 .054 .180 2.5230 ALUMINUM .007 -36 2.250 .054 .180 2.7

8、730 ALUMINUM .007 -40 2.500 .054 .180 3.0230 ALUMINUM .008 -44 2.750 .054 .180 3.2730 CRES .025 -48 3.000 .054 .171 3.5060 CRES .025 -56 3.500 .054 .171 4.0060 CRES .029 -64 4.000 .054 .171 4.5150 CRES .033 -72 4.500 .054 .227 5.1320 CRES .049 -80 5.000 .067 .224 5.6260 CRES .068 -88 5.500 .067 .224

9、 6.1260 CRES .074 NOTES: 1. MATERIAL a. ALUMINUM ALLOY 2024-T4 PER AMS-QQ-A-225/6, AMS-QQ-A-200/3, OR 2024-T3, T351 OR T3511 PER AMS-QQ-A-250/4 OR AMS-QQ-A-225/6 b. CORROSION RESISTANT STEEL 17-7PH PER AMS5528 OR AMS5529 2. HEAT TREATMENT: a. ALUMINUM: NONE b. CRES: HEAT TREAT AMS5528 TO TH950 CONDI

10、TION PER AMS2759/3 HEAT TREAT AMS5529 TO CH900 CONDITION PER AMS2759/3 3. FINISH: a ALUMINUM: ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, COLOR OPTIONAL b. CRES: PASSIVATE PER AMS2700, TYPE 2 OR TYPE 8 /4/ PROCUREMENT SPECIFICATION: AS1710 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS

11、 SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS1710 FOR THIS STANDARD. SEE FOR CURRENT QPL ON-LINE. 5. IDENTIFICATION: WASHERS SHALL BE MARKED PER AS478-35D WITH THE MANUFACTURERS NAME, TRAD

12、EMARK, OR CAGE CODE, COMPLETE “AS” PART NUMBER, AND DATE OF MANUFACTURE IN QUARTERS (3Q95 = THIRD QUARTERS 1995). WHEN SHIPPED SEPARATELY. 6. LUBRICATION: WASHERS SHALL BE COATED WITH SOLID FILM LUBRICANT TO A THICKNESS OF .0003 TO .0005 PER AS5272 TYPE I. AEROSPACE STANDARD AS1715 SHEET 3 OF 3 REV.

13、 E WASHER, COUPLING, FLEXIBLE, VARIABLE CAVITY, THREADED, FERRULE TYPE TUBE ENDS 7. SURFACE TEXTURE: SYMBOLS PER ASME Y 14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACE TO BE 125 in Ra. 8. DIMENSIONING AND TOLERANCING: ANSI Y 14.5M-1982. 9. DIMENSIONS IN INCHES. UNLE

14、SS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 2. /10/ DIMENSION SHOWN IS TO BE HELD WHEN WASHER IS INSTALLED IN A GAGE OF DIAMETER “C”. 11. EXAMPLE OF PART NUMBER: AS1715-16 BASIC WASHER NUMBER WASHER SIZE IN .062 IN INCREMENTS (16 = 1 IN TUBE SIZE) 12. A CHANGE BAR

15、(I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THIS DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.