SAE AMS-H-7199A-2013 Heat Treatment of Wrought Copper-Beryllium Alloys Process for (Copper Alloys Numbers C17000 C17200 C17300 C17500 and C17510)《锻造铍铜合金的热处理工艺(铜合金 编号为C17000、C17200、.pdf

《SAE AMS-H-7199A-2013 Heat Treatment of Wrought Copper-Beryllium Alloys Process for (Copper Alloys Numbers C17000 C17200 C17300 C17500 and C17510)《锻造铍铜合金的热处理工艺(铜合金 编号为C17000、C17200、.pdf》由会员分享，可在线阅读，更多相关《SAE AMS-H-7199A-2013 Heat Treatment of Wrought Copper-Beryllium Alloys Process for (Copper Alloys Numbers C17000 C17200 C17300 C17500 and C17510)《锻造铍铜合金的热处理工艺(铜合金 编号为C17000、C17200、.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.Copyright 2013 SAE InternationalAll rights reserved. No part of this publication may b

3、e reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (outside USA)Fax

4、: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMSH7199AAEROSPACEMATERIALSPECIFICATIONAMS-H-7199 REV. AIssued 1998-07Reaffirmed 2007-04Stabilized 2013-0

5、4Superseding AMS-H-7199Heat Treatment of Wrought Copper-Beryllium Alloys, Process for(Copper Alloys: Numbers C17000, C17200, C17300, C17500, and C17510)RATIONALEAMS-H-7199A stabilizes this document because AMS2728 contains technically equivalent requirements and is the document which will be maintai

6、ned in the future by SAE AMS Committee D.STABILIZATION NOTICEAMS-H-7199A has been declared “STABILIZED“ by AMS Committee D and will no longer be subjected to periodic reviews for currency. The last technical update of this document occurred in September 1985. Users of this document should refer any

7、certification issues (e.g. exceptions listed on the certification report) to the cognizant engineering organization for their disposition. CAUTION: In many cases the purchaser is not the cognizant engineering organization (i.e. purchaser may be a sub tier supplier).AMS Committee D recommends that th

8、e following technically equivalent (e.g. properties, fit, form, function) specification be used for future procurement. This listing does not constitute authority to substitute this specification for the “STABILIZED” specification.AMS2728 Heat Treatment of Wrought Copper Beryllium Alloy PartsCopyrig

9、ht SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS-H-7199A Page 1 of 11Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without li

10、cense from IHS-,-,-SAE AMS-H-7199A Page 2 of 11Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS-H-7199A Page 3 of 11Copyright SAE International Provided by IHS under license with SAENot for Re

11、saleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS-H-7199A Page 4 of 11Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS-H-7199A Page 5 of 11Copyright SAE Internat

12、ional Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS-H-7199A Page 6 of 11Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-

13、,-,-SAE AMS-H-7199A Page 7 of 11Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS-H-7199A Page 8 of 11Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduc

14、tion or networking permitted without license from IHS-,-,-SAE AMS-H-7199A Page 9 of 11Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS-H-7199A Page 10 of 11Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS-H-7199A Page 11 of 11Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-