SAE AMS 6466F-2008 Steel Corrosion-Resistant Welding Wire 5 2Cr - 0 55Mo《5 2Cr 0 55Mo耐腐蚀钢制焊丝》.pdf

《SAE AMS 6466F-2008 Steel Corrosion-Resistant Welding Wire 5 2Cr - 0 55Mo《5 2Cr 0 55Mo耐腐蚀钢制焊丝》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 6466F-2008 Steel Corrosion-Resistant Welding Wire 5 2Cr - 0 55Mo《5 2Cr 0 55Mo耐腐蚀钢制焊丝》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2008 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)

4、Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS6466FAMS6466F AEROSPACEMATERIALSPECIFICATIONIssued 1959-01 Noncurrent 2008-12 Superseding AMS64

5、66E Steel, Corrosion-Resistant, Welding Wire 5.2Cr 0.55Mo (Composition similar to UNS S50280) RATIONALEAMS6466F has been designated non-current based on results of a survey to aerospace users and producers. NONCURRENT NOTICE This specification has been declared “NONCURRENT” by the Aerospace Material

6、s Division, SAE, as of December 2008. It is recommended, therefore, that this specification not be specified for new designs. “NONCURRENT” refers to those specifications which have previously been widely used and which may be required for production or processing of existing designs in the future. T

7、he Aerospace Materials Division, however, does not recommend these specifications for future use in new designs. “NONCURRENT” specifications are available from SAE upon request. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted wi

8、thout license from IHS-,-,-SAE AMS6466F Page 2 of 7Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS6466F Page 3 of 7Copyright SAE International Provided by IHS under license with SAENot for Re

9、saleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS6466F Page 4 of 7Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS6466F Page 5 of 7Copyright SAE International Pr

10、ovided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS6466F Page 6 of 7Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS6466F Page 7 of 7Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-