SAE AMS 5818C-2013 Steel Corrosion and Heat Resistant Welding Wire 9 0Mn - 20Cr - 6 2Ni - 0 20N (UNS S21980)《9 0Mn 20Cr 6 2Ni 0 20N耐腐蚀和耐高温钢焊丝》.pdf

《SAE AMS 5818C-2013 Steel Corrosion and Heat Resistant Welding Wire 9 0Mn - 20Cr - 6 2Ni - 0 20N (UNS S21980)《9 0Mn 20Cr 6 2Ni 0 20N耐腐蚀和耐高温钢焊丝》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 5818C-2013 Steel Corrosion and Heat Resistant Welding Wire 9 0Mn - 20Cr - 6 2Ni - 0 20N (UNS S21980)《9 0Mn 20Cr 6 2Ni 0 20N耐腐蚀和耐高温钢焊丝》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.Copyright 2012 SAE InternationalAll rights reserved. No part of this publication may b

3、e reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (outside USA)Fax

4、: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS5818CAEROSPACEMATERIALSPECIFICATIONAMS5818 REV. CIssued 1995-12Revised 2013-02Superseding AMS5818BStee

5、l, Corrosion and Heat Resistant, Welding Wire9.0Mn - 20Cr - 6.2Ni - 0.20N(Composition similar to UNS S21980)RATIONALEAMS5818C results from a Limited Scope Ballot to correct the UNS number in the title block.1. SCOPE1.1 FormThis specification covers a corrosion and heat resistant steel in the form of

6、 welding wire.1.2 ApplicationThis wire has been used typically as filler metal for gas-metal-arc or gas-tungsten-arc welding of corrosion and heat resistant steels and alloys, but usage is not limited to such applications.2. APPLICABLE DOCUMENTSThe issue of the following documents in effect on the d

7、ate of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the

8、 last published issue of that document shall apply.2.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2248 Chemical Check Analysis Limits, Corrosion and Heat-

9、Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron AlloysAMS2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging StockAMS2813 Packaging and Marking of Packages of Welding Wire, Standard MethodAMS2814 Pa

10、ckaging and Marking of Packages of Welding Wire, Premium QualitySAE AMS5818C Page 2 of 6AMS2816 Identification, Welding Wire, Tab Marking MethodAMS2819 Identification, Welding Wire, Direct Color Code SystemARP1876 Weldability Test for Weld Filler Metal WireARP4926 Alloy Verification and Chemical Com

11、position Inspection of Welding Wire2.2 ASTM PublicationsAvailable from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM E 353 Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Ir

12、on Alloys3. TECHNICAL REQUIREMENTS3.1 Wire CompositionWire shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 353, by spectrochemical methods, or by other analytical methods acceptable to purchaser.TABLEL 1 - COMPOSITIONElement m

13、in maxCarbonManganeseSiliconPhosphorusSulfurChromiumNickelNitrogenMolybdenumCopper-8.0-19.05.50.10-0.0510.01.000.030.0321.57.00.300.750.753.1.1 Chemical analysis of initial ingot, bar, or rod stock before drawing is acceptable provided the processes used for drawing or rolling, annealing, and cleani

14、ng are controlled to ensure continued conformance to composition requirements.3.1.2 Check AnalysisComposition variations shall meet the applicable requirements of AMS2248.3.2 ConditionCold finished, bright finish, in a temper and with a surface finish which will provide proper feeding of the wire in

15、 machine welding equipment.3.3 Fabrication3.3.1 Wire shall be formed from rod or bar descaled by a process which does not affect the composition of the wire. Surface irregularities inherent with a forming process that does not tear the wire surfaces are acceptable provided the wire conforms to the t

16、olerances of 3.6.SAE AMS5818C Page 3 of 63.3.2 Butt welding is permissible provided both ends to be joined are alloy verified using a method capable of distinguishing the alloy from all other alloys processed in the facility, or the repair is made at the wire processing station. The butt weld shall

17、not interfere with uniform, uninterrupted feeding of the wire in machine welding.3.3.3 In-process annealing, if required, between cold rolling or drawing operations, shall be performed in vacuum or protective atmospheres to ensure freedom from surface oxidation and absorption of other extraneous mat

18、erials.3.3.4 Residual elements, drawing compounds, oxides, dirt, oil, dissolved gasses, and other foreign materials picked up during wire processing that can adversely affect the welding characteristics, the operation of the equipment, or the properties of the weld metal, shall be removed by cleanin

19、g processes that will neither result in pitting nor cause gas adsorption by the wire or deposition of substances harmful to welding operations.3.4 PropertiesWire shall conform to the following requirements:3.4.1 WeldabilityMelted wire shall flow smoothly and evenly during welding and shall produce a

20、cceptable welds determined by a procedure agreed upon by purchaser and vendor. The referee method of ARP1876 may be used to resolve weldability disputes.3.4.2 Spooled WireShall conform to 3.4.2.1, 3.4.2.2, and 3.4.2.3.3.4.2.1 WindingFiller metal in coils and on spools shall be wound so that kinks, w

21、aves, sharp bends, overlapping, or wedging are not encountered, leaving the filler metal free to unwind without restriction. The outside end of the electrode (the end where welding is to begin) shall be identified so it can be located readily and shall be fastened to avoid unwinding. The winding sha

22、ll be level winding.3.4.2.2 CastWire, wound on standard diameter spools as shown in Table 2 shall have imparted to it a curvature such that a specimen sufficient in length to form one loop with a 1-inch (25-mm) overlap, when cut from the spool and laid on a flat surface, shall form a circle (cast) w

23、ithin the limits shown in Table 2.3.4.2.3 HelixThe specimen on which cast was determined, when laid on a flat surface and measured between adjacent turns, shall show a vertical separation not greater than shown in Table 2.TABLE 2A - CAST AND HELIX REQUIREMENTS INCH-POUND UNITSSpool DiameterCast-Diam

24、eterInchesHelixInchesinches min max max4 2.5 15 0.588 50112 15 50 1SAE AMS5818C Page 4 of 6TABLE 2B - CAST AND HELIX REQUIREMENTS SI UNITSSpool DiameterCastMillimetersHelixMillimetersMillimeters min max max100 65 380 13200 200 1300 25300 380 1300 253.5 QualityWire, as received by purchaser, shall be

25、 uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to welding operations, operation of welding equipment, or properties of the deposited weld material.3.6 Sizes and TolerancesWire shall be supplied in the sizes and to the tolerances shown in

26、3.6.1 and 3.6.2.3.6.1 DiameterShall be as shown in Table 3.TABLE 3A - SIZES AND DIAMETER TOLERANCES, INCH/POUND UNITSFormNominal DiameterInchToleranceInchPlus andMinusCut LengthsCut LengthsSpoolsSpoolsSpools0.030, 0.035, 0.0450.062, 0.078, 0.094, 0.125, 0.156, 0.1870.007, 0.010, 0.0150.020, 0.030, 0

27、.035, 0.0450.062, 0.078, 0.0940.0010.0020.00050.0010.002TABLE 3B - SIZES AND DIAMETER TOLERANCES, SI UNITSFormNominal DiameterMillimetersToleranceMillimeterPlus andMinusCut LengthsCut LengthsSpoolsSpoolsSpools0.76, 0.89, 1.141.57, 1.98, 2.39, 3.18, 3.96, 4.750.18, 0.25, 0.380.51, 0.76, 0.89, 1.141.5

28、7, 1.98, 2.390.0250.050.0130.0250.053.6.2 LengthCut lengths shall be furnished in 18, 27, or 36-inch (457, 686, or 914-mm) lengths, as ordered, and shall not vary more than +0, -0.5 inch (-13 mm) from the length ordered.SAE AMS5818C Page 5 of 64. QUALITY ASSURANCE PROVISIONS4.1 Responsibility for In

29、spectionThe vendor of wire shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements.4.2 Cla

30、ssification of Tests4.2.1 Acceptance TestsComposition (3.1), sizes and tolerances (3.6), and alloy verification (5.2) are acceptance tests and shall be performed on each heat or lot as applicable.4.2.2 Periodic TestsWeldability (3.4.1), cast (3.4.2.2), and helix (3.4.2.3) are periodic tests and shal

31、l be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser.4.3 Sampling and TestingShall be in accordance with AMS2371.4.4 ReportsThe vendor of wire shall furnish with each shipment a report showing the results of tests for chemical composition of each

32、 heat and stating that the wire conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5818C, nominal size, and quantity.4.5 Resampling and RetestingShall be in accordance with AMS2371.5. PREPARATION FOR DELIVERY5.1 Wire shall be s

33、upplied either on spools in one continuous length for machine welding or in cut lengths for manual welding, as ordered. Wire on each spool or in each package of cut lengths shall be from the same heat of steel.5.2 Alloy Verification5.2.1 Wire from each spool or package of cut lengths shall be alloy

34、verified by a method acceptable to purchaser and vendor. The alloy verification methods of ARP4926 are recommended.5.2.2 An 8-inch (203-mm) length of wire shall be made accessible at both ends of each spool for alloy verification.5.3 IdentificationShall be in accordance with AMS2816 unless AMS2819 o

35、r another method is specified by purchaser.5.4 Packaging and MarkingShall be in accordance with AMS2813 unless AMS2814 or another method is specified by purchaser.SAE AMS5818C Page 6 of 66. ACKNOWLEDGMENTA vendor shall mention this specification number and its revision letter in all quotations and w

36、hen acknowledging purchase orders.7. REJECTIONSWire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.8. NOTES8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions,

37、not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editori

38、al changes only.8.2 Terms used in AMS are clarified in ARP1917.8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information.8.4 Purchase documents should specify not less than the following:AMS5818CSize and form (spools or cut lengths) of wire desiredLength of cut lengths or weight of spools desiredQuantity of wire desired.PREPARED BY AMS COMMITTEE “F”