SAE AMS 5032G-2005 Wire Steel 0 18 - 0 23C (SAE 1020) Annealed (UNS G10200)《退火的钢丝0 18-0 23C (SAE 1020)》.pdf

《SAE AMS 5032G-2005 Wire Steel 0 18 - 0 23C (SAE 1020) Annealed (UNS G10200)《退火的钢丝0 18-0 23C (SAE 1020)》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 5032G-2005 Wire Steel 0 18 - 0 23C (SAE 1020) Annealed (UNS G10200)《退火的钢丝0 18-0 23C (SAE 1020)》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5032G AEROSPACE MATERIAL SPECIFICATION AMS5032 REV. G Issued 1943-10 Revised 2

5、005-08 Reaffirmed 2013-10 Superseding AMS5032F Wire, Steel 0.18 - 0.23C (SAE 1020) Annealed (Composition similar to UNS G10200) RATIONALE AMS5032G has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE: 1.1 Form: This specification covers a low-carbon steel in the form of wire

6、supplied as coils of wire or, when specified, as straight lengths. 1.2 Application: This wire has been used typically for lockwire, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of

7、 this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document sh

8、all apply. 2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org. AMS 2259 Chemical Check Analysis Limits, Wrought Low-Alloy and Carbon Steels AMS 2370 Quality Assurance Sampling and Testing, Carbon and Low-Alloy Steel Wrought Products and Forging

9、 Stock SAE INTERNATIONAL AMS5032G Page 2 of 6 2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959 or www.astm.org. ASTM A 370 Mechanical Testing of Steel Products ASTM E 350 Chemical Analysis of Carbon Steel, Low-Alloy Steel, Silicon Ele

10、ctrical Steel, Ingot Iron, and Wrought Iron 3. TECHNICAL REQUIREMENTS: 3.1 Composition: Shall conform to the percentages by weight, shown in Table 1 determined by wet chemical methods in accordance with ASTM E 350, by spectrochemical methods, or by other analytical methods acceptable to purchaser. T

11、ABLE 1 - Composition Element min max Carbon 0.18 0.23 Manganese 0.30 0.60 Phosphorus - 0.040 Sulfur - 0.050 Copper - 0.15 3.1.1 Check Analysis: Composition variations shall meet the applicable requirements of AMS 2259. 3.2 Condition: Cold drawn and bright annealed. 3.3 Properties: Wire shall conform

12、 to the following requirements: 3.3.1 Tensile Properties: Shall be as shown in Table 2, determined in accordance with ASTM A 370. TABLE 2 - Tensile Properties Tensile Strength 50 to 75 ksi (345 to 517 MPa) Elongation in 10 Inches (254 mm), minimum 15% SAE INTERNATIONAL AMS5032G Page 3 of 6 3.3.2 Wra

13、pping: A length of wire not less than 12 inches (305 mm) long shall withstand, without splitting or breaking, being wrapped in a closed helix for at least six complete turns around a cylindrical mandrel having a diameter equal to the nominal diameter of the wire, and then unwrapped. 3.4 Quality: Wir

14、e, as received by purchaser, shall be uniform in quality and condition, sound, cylindrical, and free from kinks, twists, scrapes, splits, laps, seams, and other imperfections detrimental to usage of the wire. 3.4.1 The surface of the wire shall have a bright, smooth finish free from pits, abrasions,

15、 and other surface defects. 3.5 Tolerances: Diameter tolerances shall conform to Table 3. TABLE 3A - Diameter Tolerances, Inch/Pound Units Nominal Diameter Inch Tolerance, Inch plus and minus Up to 0.076, excl 0.001 0.076 to 0.249, incl 0.002 TABLE 3B - Diameter Tolerances, SI Units Nominal Diameter

16、 Millimeters Tolerance, Millimeter plus and minus Up to 1.93, excl 0.025 1.93 to 6.32, incl 0.051 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection: The vendor of wire shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purch

17、aser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements. 4.2 Classification of Tests: All technical requirements are acceptance tests and shall be performed on each heat or lot as applicable. SAE INTERNATIO

18、NAL AMS5032G Page 4 of 6 4.3 Sampling and Testing: Shall be in accordance with AMS 2370. 4.4 Reports: The vendor of wire shall furnish with each shipment a report showing the results of tests for composition of each heat and for tensile and wrapping properties of each lot, and stating that the produ

19、ct conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS 5032G, size, and quantity. 4.5 Resampling and Retesting: Shall be in accordance with AMS 2370. 5. PREPARATION FOR DELIVERY: 5.1 Identification: Shall be as follows: 5.1.1 C

20、oils or reels of wire shall each be identified by a durable tag marked with not less than the purchase order number, AMS 5032G, lot number, nominal size, quantity, and manufacturers identification, or shall be boxed and the box marked with the same information. 5.1.2 Straight lengths shall be bundle

21、d or boxed and shall have attached to each bundle or box a durable tag marked with the information of 5.1.1. 5.2 Packaging: 5.2.1 Wire shall be furnished in coils, unless otherwise ordered as straight lengths. Each coil shall be one continuous length, properly coiled, and firmly tied. 5.2.2 Packages

22、 of wire shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the wire to ensure carrier acceptance and safe delivery. 5.2.3 Protective Treatment: Wire shall be prote

23、cted from corrosion prior to shipment. 6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. SAE INTERNATIONAL AMS5032G Page 5 of 6 7. REJECTIONS: Wire not conforming to this specification, or to modifica

24、tions authorized by purchaser, will be subject to rejection. 8. NOTES: 8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of a specification. An (R) symbol to the

25、left of the document title indicates a complete revision of the specification, including technical revision. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and proper

26、ties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 Purchase documents should specify not less than the follo

27、wing: AMS 5032G Size of wire desired Form, if not as coil Quantity of wire desired. 8.5 Similar Specifications: Federal QQ-W-461 is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. 8.6 Key Words: Wire, Steel, SAE 1020, annealed, UNS G10200 PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “E”