PPI STATEMENT U-2009 STATEMENT U PPI POSITION STATEMENT ON THE USE OF PCR MATERIALS IN NON-PRESSURE POLYETHYLENE PIPE.pdf

《PPI STATEMENT U-2009 STATEMENT U PPI POSITION STATEMENT ON THE USE OF PCR MATERIALS IN NON-PRESSURE POLYETHYLENE PIPE.pdf》由会员分享，可在线阅读，更多相关《PPI STATEMENT U-2009 STATEMENT U PPI POSITION STATEMENT ON THE USE OF PCR MATERIALS IN NON-PRESSURE POLYETHYLENE PIPE.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 STATEMENT U PPI POSITION STATEMENT ON THE USE OF PCR MATERIALS IN NON-PRESSURE POLYETHYLENE PIPE (March 2009) 105 Decker Court, Suite 825, Irving, TX 75062 P: 469-499-1044 F: 469-499-1063 www.plasticpipe.org Polyethylene piping is extensively used for a wide variety of pressure and non-pressure app

2、lications from gas distribution through drainage. Equally diverse are the performance requirements for these varied applications. PE materials for all applications are required to meet recognized industry standards (i.e. ASTM, CSA, BNQ, ISO). Building standards and design procedures are evolving to

3、incorporate sustainable design elements. This is a direct result of the current social and governmental atmosphere that demands responsibility with the use of our limited non-renewable resources. The U.S. Green Building Councils Leadership in Energy and Environmental Design (LEED) program is leading

4、 the way, and recognizes the use of recycled materials in building products. Several years ago, attention was focused on incorporating post consumer recycled (PCR) polyethylene materials in polyethylene piping as a means to further plastics recycling efforts. PPI (Plastics Pipe Institute) supported

5、that initiative through an American Plastics Council ad-hoc committee of polyethylene pipe manufacturers, resin suppliers, researchers, and trade association representatives to develop means for the responsible use of post-consumer recycled polyethylene materials in polyethylene pipe. The PCR Ad-Hoc

6、 Committee chose as its mission and objective to consider the responsible use of PCR in PE piping through consensus standards writing bodies that would define the performance requirements, material properties, proper applications and test criteria for the proper use of PCR PE materials for piping ap

7、plications. PCR materials may be used in polyethylene non-pressure pipe when standards bodies for the particular piping application have established these requirements and criteria. ASTM D 3350 allows for the use of reprocessable and recyclable PE materials, as defined in ASTM D 7209, provided that

8、all specific requirements of D 3350 are met. Some ASTM and Canadian product standards allow the use of recycled materials in non-pressure PE pipe applications. As a trade association, PPIs position is that PCR materials may be used in certain non-pressure piping applications as long as they are used

9、 with the buyers knowledge and as long as the governing standard has established performance criteria to assure satisfactory long-term performance for the intended application. Thus the use of PCR PE materials in PE piping must be carefully evaluated so that long-term durability of polyethylene pipi

10、ng is assured. PPI supports continued work toward defining performance requirements, material properties, and test criteria that will result in the proper use of PCR materials in polyethylene pipe used for non-pressure applications. Additional standards that permit the use of recycled materials in n

11、on-pressure applications are being developed by standards organizations. Also, NCHRP (National Cooperative Highway Research Program) is sponsoring a research program (04-32) to investigate the use of PCR PE materials in corrugated HDPE pipe, and PPI supports this effort. Programs such as these may s

12、oon demonstrate that non-pressure corrugated HDPE piping that uses PCR PE materials may be equivalent to non-pressure corrugated HDPE pipe made from virgin HDPE compound when PCR materials are used properly. Because pressure piping requires pressure rated materials, PCR materials cannot be used for

13、pressure piping. Pressure rated materials are listed in PPI TR-4. The Plastics Pipe Institute, its member companies, and the PCR Ad-Hoc Committee support this ongoing work in development of PCR standards. Abbreviations: ASTM ASTM International BNQ Bureau de Normalisation de Quebec CSA Canadian Standards Association HDPE high density polyethylene ISO International Standards Organization PCR post consumer recycled PE - polyethylene PPI Plastics Pipe Institute TR Technical Report