NAVY MS16662 REV H-1979 GENERAL NOTES FOR STANDARD ELECTRICAL DRAWINGS《标准电子制图总说明》.pdf

《NAVY MS16662 REV H-1979 GENERAL NOTES FOR STANDARD ELECTRICAL DRAWINGS《标准电子制图总说明》.pdf》由会员分享，可在线阅读，更多相关《NAVY MS16662 REV H-1979 GENERAL NOTES FOR STANDARD ELECTRICAL DRAWINGS《标准电子制图总说明》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、FED. SUP CLASS MISC GENERAL NOTES FOR STANDARD ELECTRICAL DRAWINGS (9-S, 9000 and 803, 804, and 815 SERIES) AS LISTED IN ELECTRICAL DRAWING INDEX, AND ELECTRICAL SYMBOL LIST NAVSEA NSS030O-AU-IDX-010/SATD1 AND NAVSEA 30300-AT-GTP-O10/ESL 1. 2. 3. 5. 4. 6. 7. 8. 9. 10. 11. The provisions of MIL-E-164

2、00, Electronic, Interior Communication and All surface finishes indicated shall be in accordance with ANSI B46.1. Note 3 has been deleted. Note 4 has been deleted. Note 5 has been deleted. In lieu of continuous brazing specified on individual Military Standards, Navigation Equipment, Naval Sliip and

3、 Shore: General Specification For, which do not conflict with the provisions of this standard shall apply. the enclosures shall have each component fastened by intermittent localized brazing operations in such manner as to insure that each enclosure assembly will not be completely soft annealed and

4、willnot Each enclosure, at the completion of all drawing and.fabrication opera- distort nor leak when subjected to prescribed impact (see note 37). tions, shall be stress relieved by being uniformly heated to a temper- ature suitable for the material used. Stress relief shall be such as to reduce re

5、sidual stress from fabrication, to a minimum. However, enclo- sures.which are oven brazed as part of their fabrication process do not require additional heat treating for stress relief. The words stress relieved shall be stamped on the outside bottom sur- face of each complete unit in l/4-inch high

6、letters with black ink. All welding not specified to be by the resistance process, shall be by the manual inert-gas metal (tungsten) arc process. Welding symbols shall be in accordance with ANSI/WS A2.4. Sheet,steel enclosures: Zinc plating shall conform to type I, class 2 of QQ-2-325 or ASTM A164.

7、Sheet steel conforming to ASTM A569 finish number 1 shall be used. 12. Sheet brass enclosures: Sheet brass conformina to QQ-B-613 or ASTM B36 shall be used. 13. Sheet aluminum enc1osu;es: “ Sheet aluminum alloy conforming to QQ-A-250/8(5052) or ANSI/ASTM B209 shall be used. Temper designation is int

8、ended to indicate final temper after fabrication. 14. Folded watertight enclosures: Gasket shall be made in four pieces, Long dimension pieces shall be installed first and shall fit tightly throughout the groove and at the ends. Short dimension pieces shall then be fitted to butt tightly against the

9、 free ends of the long pieces. Gasket joints shall be made tight with rubber cement. Gaskets shall not be cemented along the qrooves. Before shirment, qasket shall be relieved of pressure. 15. Forded submersible enclosuresr Gasket length shall be such as to completely fill the retainer groove with t

10、ension. Special care shall be exercised in cutting the single bevel joint to insure smooth faces. These faces shall be securely joined by meanS.of rubber cement. At assembly with enclosure the bevel joint shall be located on a straight side. The gasket shall not be cemented in the retainer groove. B

11、efore shipment, gasket shall be relieved of pressure. ENTIRE STANDARD REVISED C C I A. ur Cu.1 SH INTERNATIONAL TITLE INTEREST GENERAL NOTES FOR STANDARD MILITARY STANDARD ELECTRICAL DRAWINGS MS16662(SH) I I 1 OCUREMENT SPECIFICATION SUPERSEDES: None Drawina 9000-S6202-74040 I Page 1 of 6 THIS DOCUM

12、ENT CONTAINS “-6 PAGES . - . - ._ - .- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-16 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29 30 31 32. 33. 34. 35. 36 37. 38. 39. 10. For drawn enclosures (molded askets) (a) &ver sealing gasket s?kr&ur

13、nished and installed. The gasket shall be installed without cement. The cover shall be tightened to provide a water-vaporproof seal during shipment. (b) Rotary shaft gland gaskets shall be treated with silicone compound conforming to MIL-S-8660 in accordance with the individual Military standard. O

14、rings shall be in accordance with MIL-P-25732 and shall be a molded type, molded to the inside diameter dimensions of the gasket retainer groove. MIL-E-917, and notes 26 and 27 herein. Enclosure shall be finished in accordance with the requirements of Note 19 has been deleted. Note 20 has been delet

15、ed. Unless otherwise specified, holes for stuffing tubes or box connectors shall be cut or drilled by the manufacturer as directed by the contract- tion of the enclosure. Stuffing tubes installed by brazing shall not ing activity. These holes shall be smooth-and true without any distor- cause warpin

16、g or distortion of the box. in the individual standard or contract or order. ing with unified and American national screw threads as specified in Drilling, countersinking, and tapping metal parts shall be done before plating or finish is applied. All sharp corners exposed to touch shall be slightly

17、rounded. Brass enclosures shall be thoroughly cleaned including soldering flux and other corrosive agents. Cleaning agent shall be neutralized after cleaning. Cleaning shall be in accordance with MIL-E-917. The interior of the enclosures shall be primed and shall be painted white, using Instructions

18、 to installing activities: enamel in accordance with TT-E-489. Stuffing tubes or box connectors shall be furnished only when so specifie Threads, unless otherwise specified, shall be right hand, class 2 comply- FED-STD-H28. - The installing activity, after jhstallation of stuffing tubes, or drilling

19、, tapping, and such, shall carefully clean and paint the MIL-E-917 except that the interior of the enclosure shall be equipment after installation in the ship, in accordance with - painted white (if not so furnished) using enamel in accordance with Note 28 has been deleted. Note 29 has been deleted.

20、 After installation, *e entire fitting shall be painted to match surround Note 31 has been deleted. Gland for switch shaft shall be packed with coil form or a preformed Counterbored holes in the bottom of insulating bases shall be filled with Tl“E-4 89. ing structure. plastic (non-metallic) packing

21、in accordance with MIL-P-16685. sealing wax or with rosin conforming to grade D of LLL-R-626, after screws are in dace. Note 34 has bee deleted. Flash shall be removed and the width of the flash edges made therebv shal: “_ Local wiring shall be funished and installed. High impact shock test for dete

22、rmining satisfactory assembly shall be in accordance with MIL-S-901. All equipment shall be considered grade A, class I. Shock mounts shall be used only where specified. be not greater than 1/32 inch. Flash edges shall then be buffed-skoth. Tests for effectiveness of enclosure shall be conducted in

23、accordance wit Switches shall conform to the requirements of MIL-S-15291. The equipnent shall meet, without failure of disruption of service, the wibration test reauirements of tvw I of MIL-STD-167-1. MIL-STD-108. o n I A. . INTERNATIONAL TITLE “ k &B INTEREST GENERAL NOTES FOR STANDARD MILITARY STA

24、NDARD ELECTRICAL DRAWINGS MS16662(SW) I I ocuRWENT SPECIFICATION SUPERSEDESI None Drawing 9000-S6202-74040 Page 2 of 6 .“ c I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MSZbbb2 REV H DR 7777732 0007780 b E I MISC 41. Castings shall be free from

25、cold shuts, blow holes, or any imperfections that may affect strength in any way. All surfaces of castings shall have all fins and burrs removed. Sand surfaces shall be disturbed as little as possible. 42. Note 42 has been deleted. 43. Note 43 has been deleted. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53

26、. P Conformance to applicable standard: No deviation in details, dimensions, and materials of the design, size and type as shown and specified on the applicable standard wil. be permitted, unless approved by the Naval Sea Systems Command (NAVSEA) . Plates for identification of equipment and for info

27、rmation shall be in accordance with MIL-P-15024 and MIL-P-15024/5. These plates when used with units that will be exposed to the weather, shall be types A, B, C, D,-I or H. Material for types A, B, C, D and I shall be nickel-copper E and G plates shall be housed within the equipment or enclosure. al

28、loy or brass. Material for type H shall be anodized aluminum. Types Type B plates when made of plastic material shall have black inner (or Labels for identification of equipment, for information or those contain- record) laminations and grey cover laminations. Wiring diagram in a holder shall be ins

29、talled on the inside of the cover ing diagrams shall be in accordance with MIL-F-16377. Note 48 has been deleted. in accordance with the requirements of MIL-E-2036. Two labels shall be attached to each fitting after painting, as follows: One shall be attached to the outside back surface of the fitti

30、ng and the Note 50.has been deleted. Plates for identification of equipment, for information, or containing ASTM B209. Markings shall be applied by a photographic process type H instructions shall be aluminum in accordance with qQ-A-250/8 or ANSI/ of MIL-P-15024. These plates may be used in lieu of

31、stamped, embossed or engraved plates where an economy will thereby be effected. Plates may be made by the metal photo process or equivalent. Information concerning this process, required by Naval activities, should be obtainel from the nearest Naval District Printing and Publication Office. Manufact

32、urers marking shall be printed on a pressure sensitive label in accordance with MIL-F-16377. Manufacturers marking shall appear on the exterior of cover or identifi- cation plate. This marking shall be either initials or monogram, and shall be depressed or embossed in the metal to provide permanent

33、identi- fication. This identification shall be that of the prime manufacturer responsible for the final acceptance of the equipment. If the manufac- turer makes only the enclosure, his identification marking shall be on the interior of the cover. other shall be attached to an inner surface. A. INTER

34、NATIONAL TITLE h., INTEREST GENERAL NOTES FOR STANDARD MILITARY STAWDAR ELECTRICAL DRAWINGS MS16662(SH: ROCUREMENT SPECIFICATION SUPERSEDES: None Drawing 9000-S6202-74040 Page 3 of 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MISC 54. Inspecti

35、on and samplin : I (a) Samplinq forvisual and dimensional examination shall be in . accordance with MIL-STD-105. Sampling for the applicable test! shall be in accordance with MIL-STD-105. For each of the small samples the-acceptance number shall be zero, and for the larger samples the acceptance num

36、bers shall be as shown for the specified AQL. Unless otherwise specified, the inspection level and the AQLs shall be as follows: “-% Ins ection Group A examination and tests: Visual and dimensional examination, and tests which do not require more than 5 minutes. II 1.5 Tests which require from five

37、minutes to eight hours and are nondestructive on units which meet the test requirement. S-4 4.0 Tests which are destructive, and tests which require more than eight hours, (destructive and non-destructive). S-2 4.0 Group B tests: Group C tests: (b) Tests for shock, vibration, surface finish and effe

38、ctiveness of enclosure need not be performed where the contractor has: (1) Passed this inspection under a previous contract and the equipment being offered is identical to that previously tested and the materials, dimensions and method of manufacture have not been changed. (c) If a classification of

39、 defects is not available for an item to be inspected, the Quality Assurance Representative Should prepare and classify a listing of the defects for the item. 55. Adjustment,-fit and general operation (by the manufacturer). Each fitting shall be subjected to an operational test to ascertain that the

40、 adjustment and fit are in accordance with the applicable standard, aid that the fitting is in a satisfactory operating condition. 56. Dielectric test- (by the manufacturer) : The interior of each fitting shall be subjected for one minute to a dielectric test voltage applied between points of polari

41、ty and also between live parts and ground. The frequency of the test voltage shall be 60 cycles r.m.s.* a.c. and shall approximate a true sine wave: (a) Effective potential shall be twice the rated voltage plus 500 (b) Effective potential shall be twice the rated voltage plus 1000 volts. volts. 57.

42、Note 57 has been deleted. 58. Cable entrance hole(s) (stuffing tubes) shall be plugged, by the manufac- turer of the enclosure or equipment, by a suitable rubber plug and compressed by the gland or cap so as to provide a water-vaporproof seal. 59. The flat side walls of drawn enclosures shall have d

43、ie score and waviness kept to a minimum in cable entrance areas. The depth of score marks or height or waviness shall not exceed 125 microinches. with a low-mu permeability indicator, conforming to MIL-1-17214. assembly, a permeability level less than 2.0. This check shall be made Material not rewor

44、ked by the prime contractor will be acceptable upon certification by the component manufacturer. 60. Nonmagnetic corrosion-resistant steel parts shall indicate, prior to A. SH I l I :oCUREMENT SPECIFICATION SUPERSEDES: None Drawing 9000-S6202-74040 Page 4 of 6 Provided by IHSNot for ResaleNo reprodu

45、ction or networking permitted without license from IHS-,-,-61. 62. 63. 64. 65. 66. 67. 68. I MISC Salt spray test shall be conducted in accordance with method 101 of MIL-STD-202. Test condition A with 5 percent salt solution shall be used. in a suitable cloth or plastic bag and packaged with the ass

46、embly. All loose parts required for installation or operation shall be provided Fittings shall be prepared for delivery in accordance with MIL-E-17555. Note 64 has been deleted. Insulation resistance: Insulation resistance of electrical circuits following the dielectric tests shall be measured with

47、a 500 volt d.c. megometer between electrical conductors and between electrical conductors and ground at approximately room temperature 75F (25OC) and at relative humidity of approximately 50 percent. Resistance shall be not less than 200 megohms. Fuse clips shall be in accordance with MIL-F-21346 an

48、d MIL-F-21346/1. Referenced documents shall be the issue in effect on &te of invitation for bids. Recommended corrections, additions or deletions shall be addressed to the contracting activity concerned. This standard takes precedence over documents referenced herein. I SH INTERNATIONAL TITLE INTERE

49、ST her Cud GENERAL NOTES FOR STANDARD MILITARY STANDARD ELECTRICAL DRAWINGS MS16662(SH) POCUREMENT SPECIFICATION SUPERSEDES: i gooo-s6202-74040 None Page 5 of 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I FED. SUP CLASS GENERAL NOTES CROSS REFERENCE I MISC 9000-S6202- Drawing 74040 To MS16662 3.-Deleted 4.-Deleted 5.-Deleted 24. 25 21. 23. 10. 19 .-Deleted 18. 26. & 27. 28.-Deleted 20.-Deleted 29. -Delete