NAVY MIL-DTL-82763 B-2011 INITIATOR CARTRIDGE ACTUATED M27 REMANUFACTURED METAL PARTS ASSEMBLY《弹药驱动引爆器 M27改制金属零件组件》.pdf

《NAVY MIL-DTL-82763 B-2011 INITIATOR CARTRIDGE ACTUATED M27 REMANUFACTURED METAL PARTS ASSEMBLY《弹药驱动引爆器 M27改制金属零件组件》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-82763 B-2011 INITIATOR CARTRIDGE ACTUATED M27 REMANUFACTURED METAL PARTS ASSEMBLY《弹药驱动引爆器 M27改制金属零件组件》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、INCH POUND MIL-DTL-82763B 25 March 2011 SUPERSEDING MIL-DTL-82763A 14 September 2004 DETAIL SPECIFICATION INITIATOR, CARTRIDGE ACTUATED, M27 REMANUFACTURED METAL PARTS ASSEMBLY This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. Th

2、is specification covers the requirements for the M27 Cartridge Actuated Initiator Remanufactured Metal Parts Assembly (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documen

3、ts cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 o

4、f this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these document

5、s are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-A-2550 Ammunition, General Specification for (Copies of these documents are available online at https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Ph

6、iladelphia, PA 19111-5094.) Comments, suggestions, or questions on this document should be addressed to DEPARTMENT OF THE NAVY, Indian Head Division, NSWC, Code E12AP, Document Control, 4123 Artisans Court, Suite 103, Indian Head, Maryland 20640-5085, OFFICIAL BUSINESS, or emailed to amanda.pennnavy

7、.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil/ DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. AMSC N/A FSC 1377 Provided by IHSNot for Resal

8、eNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-82763B 22.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise speci

9、fied, the issues of these documents are those cited in the solicitation or contract. DRAWINGS NAVAL ORDNANCE STATION, INDIAN HEAD (GAGE CODE 19200 and 19203) 10520551 Initiator, Cartridge Actuated, M27, Metal Parts Assembly 8830984 Box, Fiberboard (inner) packing, Ammunition for Initiator, Cartridge

10、 Actuated M27, M86, M87, M99, or XM107 8830985 Box, Packing, Ammunition, for Initiator, Cartridge Actuated M27, M86, M87, M98, M99, or XM017 9241155 Box, Fiberboard (Outer) Alternative Packing, Ammunition, for Initiator, Cartridge Actuated M27, M86, M87, M98, M99, or XM107 (Application for copies sh

11、ould be addressed to Commanding Officer, Naval Surface Warfare Center, Indian Head, Technical Information Branch (Code 4230), Indian Head, MD 20640.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the

12、issues of these documents are those cited in the solicitation or contract. AMERICAN SOCIETY FOR QUALITY ASQ A8402 Quality Management and Quality Assurance Vocabulary ASQ Z1.4 Sampling Procedures and Tables for Inspection by Attributes (Application for copies should be addressed to the American Socie

13、ty for Quality Control, PO Box 3005, 611 E. Wisconsin Ave., Milwaukee, WI 53201-4606.) INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ISO 3601-3 Fluid power systems O-ring Part 3: Quality acceptance criteria (Application for copies should be addressed to the International Organization for Standardiz

14、ation, 1, ch. de la Voie-Creuse, Case postale 56 CH-1211 Geneva 20, Switzerland) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothin

15、g in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials. All materials used in the manufacture of the initiators shall conform strictly to the specifications referred to on the respective drawings unless spe

16、cific approval in writing covering a departure there from has been obtained from the cognizant Navy design activity prior to manufacture. When alternate materials or methods of manufacture are specified on the drawings, the bidders selections shall be clearly stated in the proposal. The remanufactur

17、ed initiator metal parts assembly shall contain a new seal, initiator spring, O-ring, and safety pin. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-82763B 33.2 Hydrostatic pressure. The initiator chamber and cap shall withstand a hydrostati

18、c pressure of 14,000 to 15,000 pounds per square inch (psi) for 15 seconds, minimum, without deformation or mechanical failure (see 6.3.1). 3.3 Firing pin release. The firing pin of the metal parts assembly, less safety pin, shall release from the cocked position when the application of an axial loa

19、d of 15 to 30 pounds has withdrawn the initiator pin 0.370 inch, minimum, and 0.425 inch, maximum. 3.4 Initiator pin security. Application of an axial load of 200 to 220 pounds to the initiator pin of the metal parts assembly shall not withdraw the initiator pin past the safety pin. Load application

20、 shall cause no permanent deformation of the safety pin. 3.5 Protective finish. Protective finish shall be in accordance with the applicable specifications and drawings and shall apply to all surfaces of the component, regardless of configuration. Remanufactured exterior components shall have the ex

21、isting protective finish stripped and the specified protective finish reapplied (see 6.6). 3.6 Residual magnetism. The metal parts assembly shall not deflect the indicator of the compass more than five degrees in either direction using procedures in 4.6.5 (see 6.5). 3.7 Metal parts assembly. Parts s

22、hall be combined to produce an assembly, which conforms to the requirements of the metals parts assembly drawing. All threaded joints shall be assembled hand tight (see 6.5). 3.8 Workmanship. The requirements for workmanship are as specified on the applicable drawings, referenced specifications, and

23、 the following (see 6.6): 3.8.1 Metal defects. All components shall be free from cracks, splits, cold shuts, inclusions, porosity, or any similar defect. 3.8.2 Burr. No part shall have a burr which might interfere with the assembly or function of the item or which might be injurious to personnel han

24、dling the item. 3.8.3 Foreign matter. No part or assembly shall contain chips, dirt, grease, rust, corrosion, or other foreign matter. 4. VERIFICATION 4.1 Classification of inspections. The inspection requirements specified herein are classified as follows: a. Conformance inspection. 4.1.1 Quality a

25、ssurance terms and definitions. Reference shall be made to ASQ A8402 to define the quality assurance terms used. 4.1.2 Inspection. Inspection shall be in accordance with MIL-A-2550. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-82763B 44.2

26、Inspection conditioning. Unless otherwise specified (see 6.2), all inspections shall be performed under the following conditions: a. Temperature: Room ambient 20 to 25 C (68 to 77 F) b. Altitude: Normal ground c. Humidity: 50 percent relative, maximum d. Atmospheric pressure: 14.7 psia. 4.3 Quality

27、conformance inspection. 4.3.1 Lot. 4.3.1.1 Submission of product. The product shall be submitted in accordance with ASQ Z1.4. 4.3.1.2 Size of lot. For the purpose of identification and shipment, the shipping lots of metal parts assemblies shall consist of 1200 assemblies, maximum, provided the homog

28、eneity requirements of inspection lots have been retained. 4.3.2 Examination. Of reprocessed parts 100 percent examination shall be performed for all critical defects. Examination for major and minor defects shall be performed on a defect basis in accordance with the classification of defects contai

29、ned herein. Four power (4X) magnification may be used in performing visual examination for such defects as burr and foreign matter. Inspection for rubber O-rings shall be in accordance with ISO 3601-3. When compliance with the applicable requirements is in doubt as a result of visual examination, th

30、e characteristic shall be measured or gaged to determine acceptability. All nonconforming material shall be rejected. 4.3.2.1 Examination of reclaimed parts. Examination of reuseable parts, which require no reprocessing shall be limited to inspection of defects that require visual type inspection. O

31、ne hundred percent examination shall be performed for all such defects. All nonconforming parts shall be reprocessed or rejected. 4.3.2.2 Chamber, Initiator, Drawing 10520407, covering a detail of Drawing 10520551. Characteristic Defect Method of Inspection Critical None Defined Major 101 Pitch diam

32、eter of large external thread, min Gage 102 Major diameter of large external thread, min Gage 103 Pitch diameter of small external thread, min Gage 104 Major diameter of small external thread, min Gage 105 Pitch diameter of internal thread, max Gage 106 Minor diameter of internal thread, max Gage 10

33、7 Thread damage Visual 108 Metal defective Visual 109 Protective finish, inadequate or defective Visual 110 Surface finish of cavity and angle of gas port, improper Visual 111 Burr Visual 112 Foreign matter present Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without l

34、icense from IHS-,-,-MIL-DTL-82763B 5Characteristic Defect Method of Inspection Minor 201 Surface finish, improper, except as otherwise classified Visual 4.3.2.3 Cap, Initiator, Drawing 10520552, covering a detail of Drawing 10520551. Critical 1 Metal defective in mounting surface of flange Visual Ma

35、jor 101 Pitch diameter of small internal thread, max Gage 102 Minor diameter of small internal thread, max Gage 103 Pitch diameter of large external thread, max Gage 104 Minor diameter of large external thread, max Gage 105 Metal defective except as otherwise classified Visual 106 Protective finish,

36、 inadequate or defective Visual 107 Burr Visual108 Foreign matter present Visual Minor 201 Surface finish, improper Visual 4.3.2.4 Pin, Initiator, Drawing 10520553, covering a detail of Drawing 10520551. Critical None Defined Major 101 Metal defective Visual 102 Protective finish, inadequate or defe

37、ctive Visual 103 Surface finish of groove in head and face of shoulder, improper Visual 104 Burr Visual 105 Foreign matter present Visual Minor 201 Surface finish, improper, except as otherwise classified Visual 4.3.2.5 Housing, Firing Pin, Drawing 10520410, covering a detail of Drawing 10520551. Cr

38、itical None defined Major 101 Thread damaged Visual 102 Metal defective Visual 103 Protective finish, inadequate or defective Visual 104 Surface finish of cavity, improper Visual 105 Burr Visual 106 Foreign matter present Visual Minor 201 Pitch diameter for thread, min Visual 202 Major diameter for

39、thread, min Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-82763B 64.3.2.6 Pin, Firing, Drawing 10520411, covering a detail of Drawing 10520551. Critical None Defined Major 101 Metal defective Visual 102 Protective finish, inadequate

40、or defective Visual 103 Surface finish of body, improper Visual 104 Burr Visual105 Foreign matter present Visual Minor None defined 4.3.2.7 Filter, Drawing 10520414, covering a detail of Drawing 10520551. Critical None Defined Major 101 Pitch diameter of thread, min Gage 102 Major diameter of thread

41、, min Gage 103 Thread damaged Visual 104 Nylon patch not properly located or fused Manual/Visual 105 Metal defective Visual 106 Protective finish, inadequate or defective Visual 107 Burr Visual108 Foreign matter present Visual Minor None defined 4.3.2.8 Assembly, Drawing 10520551, less all drawings

42、except 10520410. Critical 1 Firing pin protrusion Gage 2 Steel ball, missing Gage 3 O-ring missing Visual 4 Seal missing Visual Major 101 Burr Visual 102 Foreign matter present Visual Minor None defined 4.3.2.9 Assembly, Drawing 10520551. Critical None defined Major 101 Firing pin cocked Manual 102

43、Initiator pin not free to rotate Manual 103 Any part missing, except as otherwise classified Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-82763B 7104 Improper assembly Visual 105 O-ring not lubricated Visual Minor 201 Protective cap

44、 missing Visual 202 Protective finish inadequate or defective Visual 4.3.2.10 Box, Fiberboard (inner Ammunition Packing, Drawing 8830984. Critical None defined Major None defined Minor 201 Contents loose Manual 202 Box damaged Visual 203 Sealing strip missing, incorrectly applied Visual 204 Marking

45、missing, incorrect or illegible Visual 205 Cut damaged or improperly sealed bag Visual 4.3.2.11 Box, Ammunition, Packing, Drawing 8830985. Critical None defined Major None defined Minor 201 Contents loose Manual 202 Strapping missing, loose, broken, or improperly assembled Manual/Visual 203 Contents

46、 of box exposed Visual 204 Box damaged Visual 205 Marking missing, incorrect or illegible Visual 206 Number of units incorrect Visual 4.3.2.12 Box, Fiberboard (Outer) Alternative, Ammunition Packing, Drawing 9241155. Critical None defined Major None defined Minor 201 Contents loose Manual 202 Box br

47、oken or damaged Visual 203 Number of units contained incorrect Visual 204 Marking missing, incorrect or illegible Visual 205 Tape incomplete Visual4.3.2.13 Spring, Initiator, Drawing 10520412, covering a detail of Drawing 10520551. Provided by IHSNot for ResaleNo reproduction or networking permitted

48、 without license from IHS-,-,-MIL-DTL-82763B 8Critical None defined Major 101 Load at specified height Gage 102 Closed length, max Gage 103 Ends incorrect Visual 104 Protective finish, inadequate or defective Visual 105 Burr Visual106 Foreign matter present Visual Minor 201 Diameter outside Gage 202

49、 Free length Gage 4.3.2.14 Pin, Safety, Drawing 10522817, covering a detail of Drawing 10520551. Critical None defined Major 101 Diameter of wire Gage 102 Profile, incorrect Visual 103 Metal defective Visual104 Protective finish, inadequate or defective Visual 105 Burr Visual106 Foreign matter present Visual Minor 201 Diameter of head, out