NAVISTAR TMS 9535-2001 Quality Requirements for Clutch Assemblies (Revision B-1).pdf

《NAVISTAR TMS 9535-2001 Quality Requirements for Clutch Assemblies (Revision B-1).pdf》由会员分享，可在线阅读，更多相关《NAVISTAR TMS 9535-2001 Quality Requirements for Clutch Assemblies (Revision B-1).pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside Navistar International Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. Ge31999 by Navistar International Transportation Corp. APRIL 1999 Page 1 of 2 INTERN

2、ATIONAL TRUCK AND ENGINE CORPORATION TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TMS-9535 TITLE: Quality Requirements For Clutch Assemblies REVISION: B-1 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering DATE ISSUED: August 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFI

3、ED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the appl

4、icability of regulatory limits prior to use. Change Notice: Reformatted and Editorial Changes Reference: Keywords: Clutch Assemblies 1.0 APPLICATION This specification covers the quality control requirements for purchased clutch assemblies provided as completed units to International plants. 2.0 SCO

5、PE This specification covers the quality plan, KCC quality control, source approval, and identification requirements. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following standards, specifications and regulations are referenced i

6、n this specification. Quality System Standard QS-9000 (ISO 9001) INTERNATIONAL IQR Quality Standard INTERNATIONAL Manufacturing Standard D-13 CFR Title 29, Part 1910 4.0 GENERAL REQUIREMENTS Product supplied shall be suitable for its intended application. 5.0 QUALITY All clutches supplied shall be d

7、elivered in a clean and dry condition. All clutch assembly/test fluids/greases which may remain or leave a residue in the clutch must be compatible with International factory fill fluids/greases. Cover Assemblies shall be free of rust and cracks. Driven Discs, and Intermediate Plates shall be free o

8、f rust, cracks, pits, gouges, nicks, and scratches and all friction surfaces shall be free from paint, dirt, oil, or damage which could affect the torque carrying capabilities of the clutch. NUMBER: TMS-9535 TITLE: Quality Requirements For Clutch AssembliesREVISION: A This document is restricted and

9、 may not be sent outside Navistar International Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. Ge31999 by Navistar International Transportation Corp. APRIL 1999 Page 2 of 2 5.1 Control Plan A Quality Control Pla

10、n for this product will be established by mutual agreement between International and the supplier. The following items, where applicable,* will be included in the control plan as dimensional features for management by statistical process control.* Stamped Clutches Only 1. Clutch Mounting Holes Locat

11、ion 2. Clutch Mounting Holes Diameter Cast Clutches Only 1. Pilot Diameter 2. Intermediate Plate Lug Width/Slot Width 3. Drive Pin Flat Thickness 4. Drive Pin Shank Diameter 5. Drive Pin Concentricity Between Shank and Flat * Additional characteristics for inclusion in the control plan may be specif

12、ied on the engineering drawing and/or purchase order. * See International Engineering Design Standard A-16. 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements Suppliers must conform to the requirements of the International IQR Quality Standard which includes conformance to the QS-9000

13、 (ISO 9001) Quality System Standard. A mutually acceptable Quality Control Plan as described therein is required for source approval to the requirements of this specification. 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respec

14、ts to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify

15、 Materials Engineering at TDTC and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 s

16、hall be submitted with the request for change. 6.3 Process Control The supplier shall either perform and report results of tests on specific lots of parts produced or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providin

17、g all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using International plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATION Loading, packing, and identification shall be in accordance with Manufacturing Std.D-13. 8.0 DESIGNATION ON DRAWINGS The drawing will utilize the KCC symbol with a note that: Completed assemblies will comply with Requirements of TMS-9535. KCCKCC