FORD WSS-M99D68-A1-2013 THERMOPLASTIC PROPERTY DETERMINATION FOR CAE HIGH STRAIN RATE TENSILE CREEP AND TENSILE MODULUS TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M99D68-A1-2013 THERMOPLASTIC PROPERTY DETERMINATION FOR CAE HIGH STRAIN RATE TENSILE CREEP AND TENSILE MODULUS TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M99D68-A1-2013 THERMOPLASTIC PROPERTY DETERMINATION FOR CAE HIGH STRAIN RATE TENSILE CREEP AND TENSILE MODULUS TO BE USED WITH FORD WSS-M99P1111-A .pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2013 08 05 Released M. Corley, EU L. Soreide, FNA Controlled document at www.MATS Copyright 2013, Ford Global Technologies, LLC Page 1 of 4 THERMOPLASTIC PROPERTY DETERMINATION FOR CAE, WSS-M99D68-A1 HIGH STRAIN RATE TENSILE, CREEP AND

2、 TENSILE MODULUS 1. SCOPE This specification defines the requirements for measuring selected material properties used in CAE simulation or equivalent modeling of automotive components made from thermoplastic production materials. 2. APPLICATION This specification was released originally to communica

3、te test methods and test parameters for material property data collection to the thermoplastic material suppliers. The data can then be combined with other material property data to model automotive components made from the material. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS

4、 Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A). 3.2 SAMPLE PREPARATION Test specimens must be milled out of injection molded plaques with film gate injection on the short side. Plaque size should be approximately 25

5、0 mm x 150 mm x 3.0 mm. The specimens must not be taken from the edges or in the film gate area of the plaque to avoid the skin effects of the injection molding process. Specimen A 150 minimum x 10 x 4.0 +/- 0.2 mm (ISO 527-2, Type 1A) Specimen J 80 mm x 15 mm x 3.0 +/- 0.2 mm (ISO 8256, Type 3) Spe

6、cimen K 250 minimum x 25 x 3.0 +/- 0.2 mm (ISO 527-4, Type 2) 3.2.1 Number of samples The number of samples will be determined by Ford Materials Engineering, Ford CAE, and the material supplier based on the number of optional conditions selected. Supplement A is to be used to communicate the number

7、of optional test parameters included in the material testing. Laboratories capable of running the test methods are listed in the General Information section. 3.3 TENSILE MODULUS (ISO 527-4, Specimen K, 5 mm/minute, 23 C) Unreinforced Sample Orientation: 0 Report Modulus, GPa Fiber Reinforced Sample

8、Orientation: 0, 90 Report Modulus, GPa Optional: 45 Report Modulus, GPa ENGINEERING MATERIAL SPECIFICATION WSS-M99D68-A1 Copyright 2013, Ford Global Technologies, LLC Page 2 of 4 3.4 CREEP MODULUS (ISO 899-1, Specimen A, Flow Direction, at 23 C, 65 C, 90 C and 110 C at 5, 10 and 15 MPa) 1 hour Repor

9、t Value, MPa 1000 hours Report Value, MPa Provide data creep plots (% Strain vs. Time in hours), individual data points at each stress level and Isochronous Stress-Strain Plot. 3.5 HIGH STRAIN RATE TENSILE TESTING OF POLYMERS Report all Data (SAE J2749, Except Sample Preparation for Specimen J descr

10、ibed above) Sample Orientation to Flow Direction: Unreinforced Sample Orientation: 0 Optional: 90, 45 Fiber Reinforced Sample Orientation: 0, 90 Optional: 45 Required Strain Rates: 0.01/sec, 1/sec, 100/sec or others as mutually agreed upon Optional: 10/sec, 300/sec, or others as mutually agreed upon

11、 Temperatures: 23 C Optional: -30 C, 65 C or others as mutually agreed upon Strain Measurement: Local strain measurement on the sample should be used. Provide Force-Displacement and Engineering Stress vs. Engineering Strain data in digital format (MS Excel). If optical strain measurement is used pro

12、vide True Stress vs. True Strain data (optional). The data should not be filtered. Table 1: Minimum Sample Size Para. Test Minimum Lots Specimens per Condition Total Test Specimens (minimum) 3.3 Tensile Modulus At least 1 orientation for unreinforced (0) At least 2 orientations for reinforced (0, 90

13、) 1 5 5 10 3.4 Creep Modulus 3 stress levels (5, 10, 15 MPa) 4 temperatures (23, 65, 90, 110C) 2 times (1 and 1000 hours) 1 2 48 3.5 High Strain Rate At least 3 strain rates (0.01/sec, 1/sec, 100/sec) At least 1 temperature (23C) At least 1 orientation for unreinforced (0) At least 2 orientations fo

14、r reinforced (0, 90) 1 5 15 30 ENGINEERING MATERIAL SPECIFICATION WSS-M99D68-A1 Copyright 2013, Ford Global Technologies, LLC Page 3 of 4 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for q

15、uestions concerning Engineering Material Specifications. This specification is intended to compliment existing Ford Engineering Material Specifications for thermoplastics and the data collected and stored in the Ford Materials Database. Laboratories with known test capability. Datapoints Labs http:/

16、 95 Brown Road, Ithaca, NY 14850 Phone: 607-266-0405 Fax: 607-266-0168 Toll-Free (U.S.): 1-888-328-2422 EDAG GmbH & Co. KGaA ATC FULDA, Jan Frster Steinauerstrae 20 36100 Petersberg Phone.: +49 661 6000-9151 Fax: +49 661 6000 818 ENGINEERING MATERIAL SPECIFICATION WSS-M99D68-A1 Copyright 2013, Ford

17、Global Technologies, LLC Page 4 of 4 Supplement A CAE Modeling Data that compliments an existing Resin Specification Material Name _ Supplier Name _ Material Specification _ Testing Laboratory _ Circle optional parameters to make them required. Tensile Modulus Required Orientations: Unreinforced: 0

18、Fiber Reinforced: 0 and 90 Optional: 45 Other: _ Required Temperature: 23 C Other: _ Creep Modulus Required Stress Levels: 5 MPa 10 MPa 15 MPa Other:_ Required Temperatures: 23 C 65 C 90 C 110 C Other:_ High Strain Rate Tensile Testing of Polymers. Required Strain Rates: 0.01/sec 1/sec 100/sec Optional: 10/sec 300/sec Other_ Required Temperature: 23 C Optional: -30 C 65 C Other:_ Required Orientation Unreinforced: 0 Reinforced: 0 and 90 Optional: 45 Other: _ Material Card _ Date_ Materials Engineering Signature _