FORD WSS-M2C952-A1-2016 OIL ENGINE INITIAL FILL SAE 0W-20 TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M2C952-A1-2016 OIL ENGINE INITIAL FILL SAE 0W-20 TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M2C952-A1-2016 OIL ENGINE INITIAL FILL SAE 0W-20 TO BE USED WITH FORD WSS-M99P1111-A .pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions Rev. 0 2016 05 18 Released S. Abdelhalim, FOE Controlled document at www.MATS Copyright 2016, Ford Global Technologies, Inc. Page 1 of 14 OIL, ENGINE, INITIAL FILL SAE 0W-20 WSS-M2C952-A1 1. SCOPE This material specification defines the minimu

2、m acceptable performance requirements and physical/chemical properties of engine oils to be used by Ford Motor Company in its worldwide engine/vehicle manufacturing and service operations. 2. APPLICATION This specification is released in Europe and, where applicable, in RoW for initial fill engine o

3、ils used for lubrication of compression ignition engines using diesel fuel and for spark ignition engines using gasoline fuel. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used

4、when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 PERFORMANCE Where applicable, the spec shall meet engine and bench tests for ACEA C2 as per ACEA (201

5、2) or latest ACEA sequence, with the exception of SAE J300 viscosity grade, and in addition to Ford specific tests as stated here under. 3.2.1 General Test Requirements All engine performance and bench testing used to support a claim of compliance with this specification should be conducted accordin

6、g to CEC, ASTM or Ford internal procedures as applicable. Formulation should be developed according to the relevant industry standards (ATIEL CoP, ATC CoP, ACC CoP Report values - “NIL“ or Trace“ are not permissible S _ _ _ _ _ P _ _ _ _ _ Zn _ _ _ _ _ Ba _ _ _ _ _ Ca _ _ _ _ _ Mg _ _ _ _ _ Na _ _ _

7、 _ _ N _ _ _ _ _ B _ _ _ _ _ Cu _ _ _ _ _ Cl _ _ _ _ _ Sulfated Ash _ _ _ _ _ V. Tests Conducted _ _ _ _ _ Comments: _ _ _ _ _ Signature_ Title_ ENGINEERING MATERIAL SPECIFICATIONWSS-M2C952-A1 Copyright 2016, Ford Global Technologies, Inc. Page 11 of 14 (Supplement A, p. 6 of 7) Oil Company_ Date_ P

8、roduct Name_ Viscosity Grade_ Product Code_ Specification Test Mfg. Physical/Chemical Properties Requirements Results Limits Viscosity at 150 C (ASTM D445), mm2/s report _ _ Viscosity at 100 C (ASTM D445), mm2/s 6.9 .001%) report _ _ Cleanliness Specification (Initial Fill Only) ISO4406 Particle Cou

9、nt per millilitre Particle Sizes larger than 4 microns 160,000max _ _ Particle Sizes larger than 6 microns 80,000max _ _ Particle Sizes larger than 14 microns 2,500max _ _ Signature_ Title_ ENGINEERING MATERIAL SPECIFICATIONWSS-M2C952-A1 Copyright 2016, Ford Global Technologies, Inc. Page 13 of 14 (

10、Supplement B, p. 1 of 1) Oil Company_ Date_ Product Name_ Viscosity Grade_ Product Code_ Quality Control Certification Physical/Chemical Properties Approved Limits Frequency Viscosity at 150 C (ASTM D445), mm2/s _ _ Viscosity at 100 C (ASTM D445), mm2/s _ _ Viscosity at 40 C (ASTM D445), mm2/s _ _ D

11、ensity (ASTM D 1298), kg/L _ _ Viscosity at -25 C (ASTM D5293), mPa.s _ _ Viscosity at -30 C (ASTM D5293), mPa.s _ _ Low Temp. Pumping Viscosity at -30 C, mPa.s _ _ (ASTM D4684) at -35 C, mPa.s _ _ Pour Point (ASTM D97), C _ _ Stable Pour Point (SAE J 300 App. B), C _ _ Gelation Index (ASTM D5133) _

12、 _ Flash Point (ASTM D93), C _ _ Volatility Evap. Loss, 1 h at 250 C (ASTM D5800), % _ _ Shear Stability (ASTM D445), mm2/s at 100 C After ASTM D6278 or CEC L-14-A-93 _ _ Viscosity at 150 C and 106s-1 CEC L-36-A-90, mPa.s New Oil _ _ After ASTM D 6278 or CEC L-14-A-93 _ _ Copper Corrosion (ASTM D130

13、, 3 h at 100 C) _ _ Filterability (ASTM D6795), % flow reduction, max _ _ Water Tolerance (ASTM D 6794), % _ _ Foaming (ASTM D 892) without Option A Sequence I, mL _ _ Sequence II, mL _ _ Sequence III, mL _ _ High Temperature Foaming (ASTM D6082), mL _ _ Total Acid Number (ASTM D664), mg KOH/g _ _ T

14、otal Base Number (ASTM D2896), mg KOH/g _ _ Sulfated Ash (ASTM D874), % _ _ Phosphorus content, % _ _ Cleanliness Max Particle Size _ _ Cleanliness Particle Count _ _ Barium, % _ _ Boron, % _ _ Calcium, % _ _ Chlorine, % _ _ Copper, % _ _ Magnesium, % _ _ Molybdenum, % _ _ Nitrogen, % _ _ Potassium, % _ _ Silicon, % _ _ Sodium, % _ _ Sulfur, % _ _ Zinc, % _ _ Other (.001%) _ _ ENGINEERING MATERIAL SPECIFICATIONWSS-M2C952-A1 Copyright 2016, Ford Global Technologies, Inc. Page 14 of 14 Signature_ Title_ Materials Engineering Concurrence_