FORD FLTM BJ 128-04-2001 STAINING AND SOFTENING OF PAINTED SURFACES BY RUST PREVENTIVE COMPOUNDS《防锈剂对涂漆表面的着色和软化性能》.pdf

《FORD FLTM BJ 128-04-2001 STAINING AND SOFTENING OF PAINTED SURFACES BY RUST PREVENTIVE COMPOUNDS《防锈剂对涂漆表面的着色和软化性能》.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BJ 128-04-2001 STAINING AND SOFTENING OF PAINTED SURFACES BY RUST PREVENTIVE COMPOUNDS《防锈剂对涂漆表面的着色和软化性能》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHOD BJ 128-04 Date Action Revisions 2001 07 25 Revised Editorial no technical change A. Cockman 1996 06 05 Printed copies are uncontrolled Page 1 of 2 Copyright 2001, Ford Global Technologies, Inc. STAINING AND SOFTENING OF PAINTED SURFACES BY RUST PREVENTIVE COMPOUNDS Appli

2、cation This procedure is used to determine the tendency for rust preventive compounds, used in exterior or interior automotive applications, to stain or soften painted surfaces that are exposed to heat and/or sunlight. Apparatus Required Oven Approximate internal dimensions: 725 mm wide, 610 mm deep

3、, and 520 mm high capable of maintaining a temperature of 45 +/- 2 C. The oven is to be equipped with thermostat control and a red pilot light. A Grieves-Henry oven (Model CR-326, Model PL-1) or equivalent is suitable. Fluorescent Sunlamp Cabinet Modified oven as shown above equipped with sunlamp fi

4、xture shown below. Sunlamp Fixture - #PL-326* or equivalent To be completely installed in the oven. 20 gauge steel box with screw cover; two 20 watt high power-factor ballasts; 4 fluorescent starter assemblies; 4 pairs fluorescent lamp holders; 4 FS 20T-12 fluorescent sunlamps. *Source: Infra Corpor

5、ation 5454 Dixie Highway Waterford, MI 48239-1615 Telephone: (248) 623-0400 Thickness Gage A Gardner or equivalent wet film thickness gage. Source: VWR Scientific (Catalog No. 52625-001) Microhardness Tester Tukon hardness tester or equivalent. FORD LABORATORY TEST METHOD BJ 128-04 Page 2 of 2 Copyr

6、ight 2001, Ford Global Technologies, Inc. Materials Required Cloth Shall be suitable for wiping rust preventive from a painted panel. Test Panel Refer to FLTM BI 103-02, Method B,2 or as specified in the applicable material specification. The panel(s) shall be freshly painted within 72 hours of init

7、iating testing using and baked to the minimum requirements of the current production white topcoat enamel. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 2

8、4 h prior to testing and tested under the same conditions unless otherwise specified. Procedure 1. Check the microhardness of the painted surface(s) before test exposure per FLTM BI 112-02. 2. Apply rust preventive compound on current production white, base/clear coat enamel, painted panels (or base

9、/clearcoat enamel as referenced in the rust preventive specification). 3. Expose one panel in the fluorescent sunlamp cabinet at 45 /- 2 C for 16 hours. Expose a second panel in oven only at 45 +/- 2 C for 16 hours. 4. After exposure, remove the rust preventive from the panel with a soft cloth satur

10、ated with a suitable solvent. 5. Check the microhardness (as in step 1) of the paint on the areas of the test specimen on which the rust preventive was smeared. Report any staining or softening of the paint in the areas that had been covered with the rust preventive compound. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities.