ETSI TS 122 146-2016 Digital cellular telecommunications system (Phase 2+) Universal Mobile Telecommunications System (UMTS) LTE Multimedia Broadcast Multicast Service (MBMS) Stage.pdf

《ETSI TS 122 146-2016 Digital cellular telecommunications system (Phase 2+) Universal Mobile Telecommunications System (UMTS) LTE Multimedia Broadcast Multicast Service (MBMS) Stage.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 122 146-2016 Digital cellular telecommunications system (Phase 2+) Universal Mobile Telecommunications System (UMTS) LTE Multimedia Broadcast Multicast Service (MBMS) Stage.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 122 146 V13.0.0 (2016-02) Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Multimedia Broadcast/Multicast Service (MBMS); Stage 1 (3GPP TS 22.146 version 13.0.0 Release 13) TECHNICAL SPECIFICATION ETSI ETSI TS 122 146 V13.0.0 (20

2、16-02)13GPP TS 22.146 version 13.0.0 Release 13Reference RTS/TSGS-0122146vd00 Keywords GSM,LTE,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous

3、-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall n

4、ot be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secr

5、etariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please se

6、nd your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permissio

7、n of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ET

8、SI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 122 146

9、V13.0.0 (2016-02)23GPP TS 22.146 version 13.0.0 Release 13Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, a

10、nd can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to th

11、e ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. For

12、eword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the co

13、rresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “c

14、annot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 122 146 V13.0.0 (2016-02)33GPP TS 22.146 version 13.0.0 Rel

15、ease 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4g3Introduction 4g31 Scope 5g32 References 5g33 Definitions, symbols and abbreviations . 5g33.1 Definitions 5g33.2 Abbreviations . 6g34 General description of a multimedia broadcast/multicast service

16、(MBMS) 7g34.1 MBMS broadcast mode 7g34.2 MBMS multicast mode 8g34.2.1 Multicast subscription and reception 9g34.3 Discovery and announcement of MBMS services 9g35 High level requirements . 10g35.1 Broadcast mode 10g35.1.1 Home environment requirements 10g35.1.2 User requirements for MBMS 11g35.2 Mul

17、ticast mode . 11g35.2.1 Home environment requirements 11g35.2.2 User requirements for MBMS 12g35.3 Availability . 13g36 Security. 13g37 Charging . 14g37.1 Broadcast mode 14g37.2 Multicast mode . 14g3Annex A (informative): MBMS Bit Rates 15g3Annex B (informative): Change history . 16g3History 18g3ETS

18、I ETSI TS 122 146 V13.0.0 (2016-02)43GPP TS 22.146 version 13.0.0 Release 13Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG

19、approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval

20、; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. Introducti

21、on Broadcast and Multicast are methods for transmitting data-grams from a single source to several destinations (point-to-multipoint). To date, release-4 and release-99 define two services in this respect: A cell broadcast service (CBS) allowing for low bit-rate data to be transmitted to all subscri

22、bers in a set of given cells over a shared broadcast channel. This service offers a message-based service 5,6 An IP-Multicast service allowing for mobile subscribers to receive multicast traffic. This service does not allow for multiple subscribers to share radio or core network resources and as suc

23、h does not offer any advantages as far as resource utilization within the PLMN and over the radio access network. 3,4 It is envisaged that for some applications, multiple users can receive the same data at the same time. The benefit of multicast and broadcast in the network is that the data is sent

24、once on each link. For example, an SGSN will send data once to an RNC regardless of the number of Node Bs and UEs that wish to receive it. The benefit of multicast and broadcast on the air interface is that many users can receive the same data on a common channel, thus not clogging up the air interf

25、ace with multiple transmissions of the same data. With increasing use of high bandwidth applications in third generation mobile systems, especially with a large number of users receiving the same high data rate services, efficient information distribution is essential. Thus, broadcast and multicast

26、are techniques to decrease the amount of data within the network and use resources more efficiently ETSI ETSI TS 122 146 V13.0.0 (2016-02)53GPP TS 22.146 version 13.0.0 Release 131 Scope This Technical specification defines the stage one description of the Broadcast and Multicast Services for the 3G

27、PP System. Stage one is the set of requirements which shall be supported for the provision of Broadcast and Multicast services, seen primarily from the subscribers and service providers points of view. Note: Non-3GPP access systems may provide MBMS transport service, but this is not in the scope of

28、this specification. This TS includes information applicable to network operators, content providers, and terminal and network manufacturers. This TS contains the core requirements for Multicast and Broadcast Services, which are sufficient to provide a complete service. 2 References The following doc

29、uments contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a

30、 non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TR 21.905: “Vocabulary for 3GPP Specifi

31、cations “. 2 RFC 1112: “Host extensions for IP multicasting“, RFC 1920:“ Internet official protocol standards“, RFC 1458: “Requirements for multicast protocols“, RFC 1301: “Multicast transport protocol“ 3 3GPP TS 22.060: “General Packet Radio Service (GPRS); Service description; Stage 1“. 4 3GPP TS

32、23.060: “General Packet Radio Service (GPRS); Service description; Stage 2“. 5 3GPP TS 25.324: “Broadcast/Multicast Control BMC” 6 3GPP TS 23.041: “Technical Realization of Cell Broadcast Service (CBS)” 7 3GPP TS 22.246: “MBMS User Services“. 3 Definitions, symbols and abbreviations 3.1 Definitions

33、For the purposes of the present document, the definitions in 3GPP TR 21.905 1 as well as the following definitions apply. Broadcast service area: The area in which a specific broadcast service is available. It is defined individually per broadcast service. The broadcast service area may represent th

34、e coverage area of the entire PLMN, or part(s) of the PLMNs coverage area. The broadcast service area is the sum of all local broadcast areas offering the same service. Local Broadcast Area: The area of a broadcast service, where the service content is the same. One broadcast service may have differ

35、ent content in different local broadcast areas. Broadcast mode: The part of MBMS that supports broadcast services. ETSI ETSI TS 122 146 V13.0.0 (2016-02)63GPP TS 22.146 version 13.0.0 Release 13Broadcast service: A unidirectional point-to-multipoint service in which data is efficiently transmitted f

36、rom a single source to multiple UEs in the associated broadcast service area. Broadcast services may be received by all users who have enabled the specific broadcast service locally on their UE and who are in the broadcast area defined for the service. Broadcast session: A continuous and time-bounde

37、d reception of a broadcast service by the UE. A single broadcast service can only have one broadcast session at any time. A broadcast service may consist of multiple successive broadcast sessions. Mobile Station (MS): Defined in 3GPP TS 24.002. (The abbreviation “UE“ in this specification refers bot

38、h to MS and User Equipment.) Multicast transmission activation: The process by which the network activates the transmission of Multicast data. Multicast service area: The area in which a specific multicast service is available. It is defined individually per multicast service. The multicast service

39、area may represent the coverage area of an entire PLMN, or part(s) of the PLMNs coverage area. The multicast service area is the sum of all local multicast areas offering the same service. Local multicast area: The area of a multicast service, where the service content is the same. One multicast ser

40、vice may have different content in different local multicast areas. Multicast mode: The part of MBMS that supports multicast services. Multicast joining: The process by which a user joins a multicast group. Multicast session: A continuous and time-bounded reception of a multicast service by the UE.

41、A single multicast service can only have one multicast session at any time. A multicast service may consist of multiple successive multicast sessions. Multimedia Broadcast/Multicast Service (MBMS): A unidirectional point-to-multipoint service in which data is transmitted from a single source entity

42、to a group of users in a specific area. The MBMS has two modes: Broadcast mode and Multicast mode. Multicast group: A group of users that have an activated MBMS in multicast mode and therefore are ready to or are receiving data transmitted by this service. The multicast group is a subset of the Mult

43、icast subscription group. Multicast subscription group members may join the corresponding multicast group. Multicast service: A unidirectional point-to-multipoint service in which data is efficiently transmitted from a single source to a multicast group in the associated multicast service area. Mult

44、icast services can only be received by such users that are subscribed to the specific multicast service and have joined the multicast group associated with the specific service. Multicast subscription: The process by which a user subscribes or is subscribed to a multicast subscription group and ther

45、eby is authorised to join certain multicast services. Multicast subscription is performed either upon user selection or due to home environment initiation. Multicast Subscription Group: A group of users who are subscribed to a certain MBMS in multicast mode and therefore authorised to join and recei

46、ve multicast services associated with this group. User Equipment: defined in TS 21.905. An occurrence of a User Equipment is an MS for GSM as defined in TS 24.002. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: MBMS Multimedia Broadcast/Multicast Servi

47、ce MS Mobile Station UE User EquipmentETSI ETSI TS 122 146 V13.0.0 (2016-02)73GPP TS 22.146 version 13.0.0 Release 134 General description of a multimedia broadcast/multicast service (MBMS) Point to multipoint services exist today which allow data from a single source entity to be transmitted to mul

48、tiple endpoints. These services are expected to be used extensively over wireless networks, hence there is a need for a capability in the PLMN to efficiently support them. The Multimedia Broadcast/Multicast Service (MBMS) will provide this capability for such broadcast/multicast services provided by

49、 the home environment and other VASPs. The MBMS is a unidirectional point to multipoint bearer service in which data is transmitted from a single source entity to multiple recipients. It is anticipated that other services will use these bearer capabilities. MBMS also enables an IMS application located on an application server to send multimedia to a set of IMS users in the service area by means of MBMS bearer service. 3GPP has defined two modes of operation: - the broadcast mode - the multicast mode. 4.1 MBMS broadcast mode The broadcast mode