ETSI TS 100 396-10-2000 Terrestrial Trunked Radio (TETRA) Technical Requirements for Direct Mode Operation (DMO) Part 10 Managed Direct Mode Operation (M-DMO) (V1 1 1)《陆地集群无线电(TETR_1.pdf

《ETSI TS 100 396-10-2000 Terrestrial Trunked Radio (TETRA) Technical Requirements for Direct Mode Operation (DMO) Part 10 Managed Direct Mode Operation (M-DMO) (V1 1 1)《陆地集群无线电(TETR_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 100 396-10-2000 Terrestrial Trunked Radio (TETRA) Technical Requirements for Direct Mode Operation (DMO) Part 10 Managed Direct Mode Operation (M-DMO) (V1 1 1)《陆地集群无线电(TETR_1.pdf（39页珍藏版）》请在麦多课文档分享上搜索。

1、ETSI TS 100 396-10 1.1.1 (2000-12) Technical Specification Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part IO: Managed Direct Mode Operation (M-DMO) 2 ETSI TS 1 O0 396-1 O V1.l.l (2000-1 2) Reference DTSnETRA-02042-1 O Keywords DMO, PDO, TETRA, data, r

2、adio ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present documen

3、t can be downloaded from: http:/iwww. etsi I oq The present document may be made available in more than one electronic version or in print. In any ase of existina c u perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispu

4、te, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ET

5、SI documents is available at If you find errors in the present document, send your comment to: editor etsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. 8 European Telec

6、ommunications Standards Institute 2000. All rights reserved. ETSI 3 ETSI TS 1 O0 396-1 O V1.l.l (2000-1 2) Contents Intellectual Property Rights 5 Foreword 5 1 Scope 6 2 References 6 3 Definitions and abbreviations 7 3.1 Definitions 7 3.2 Abbreviations 9 4 Overview of M-DMO . 9 5 M-DM-MS . 12 5.1 5.

7、2 5.3 5.4 5.4.1 5.4.2 5.4.3 Operation of M-DM-MS 12 M-DM-MS authorized by M-DM-AUTH . 12 V+D authorized M-DM-MS 13 Transmit authorization for M-DM-MS . 13 Transmit authorization for M-DM-MS authorized by M-DM-AUTH 13 Transmit authorization for V+D authorized M-DM-MS 15 Release cause element 15 6 M-D

8、M-AUTH 15 6.1 Operation of M-DM-AUTH . 15 6.2 Loss of link to SwMI . 16 6.3 Managed out-of-range or dual mode operation . 17 6.4 Maintaining link to M-DM-MSs 17 6.5 M-DM-AUTH direct mode procedures 17 6.5.1 Direct mode procedures for stand-alone M-DM-AUTH 17 6.5.1.1 General . 17 6.5.1.2 Basic capabi

9、lities of stand-alone M-DM-AUTHs physical layer 17 6.5.1.3 State definitions for stand-alone M-DM-AUTH . 18 6.5.1.4 Channel surveillance procedures for stand-alone M-DM-AUTH 18 6.5.1.4.1 Initial determination of DM channel state by stand-alone M-DM-AUTH 18 6.5.1.4.2 Channel surveillance procedures a

10、fter initial determination of channel state . 19 6.5.1.4.3 Channel surveillance only prior to transmission of presence signal . 19 6.5.1.5 Criteria for changing state for stand-alone M-DM-AUTH 20 6.5.1.6 Linearization by stand-alone M-DM-AUTH 20 6.5.2 Direct mode procedures for M-DM-REP, M-DM-GATE o

11、r M-DM-REP/GATE . 20 6.6 M-DM-AUTH V+D procedures . 20 7 Operation of M-DMO channels . 20 7.1 General procedures 20 7.2 Withdrawing authorization 21 7.3 Power class . 21 8 Authorization presence signal . 21 8.1 M-DMO presence signal 21 8.2 Transmission rules for authorization presence signal 22 8.2.

12、1 Transmission of presence signal by stand-alone M-DM-AUTH . 22 8.2.1.1 Channel free . 22 8.2.1.1.1 Carrier free 22 8.2.1.1.2 One DM channel free 23 8.2.1.2 Channel occupied or reserved . 23 8.2.2 Transmission of presence signal by M-DM-REP . 23 8.2.3 Transmission of presence signal by M-DM-GATE or

13、M-DM-REP/GATE 24 8.3.1 DPRES-SYNC PDU for stand-alone M-DM-AUTH . 25 8.3.1.1 Definition of DPRES-SYNC PDU for stand-alone M-DM-AUTH . 25 8.3 DPRES-SYNC PDU 24 ETSI 4 ETSI TS 1 O0 396-1 O V1.l.l (2000-1 2) 8.3.1.2 8.3.1.2.1 8.3.1.2.2 8.3.1.2.3 8.3.1.2.4 8.3.1.2.5 8.3.1.2.6 8.3.1.2.7 8.3.1.2.8 8.3.1.2

14、.9 8.3.1.2.10 8.3.1.2.11 8.3.1.2.12 8.3.1.2.13 8.3.1.2.14 8.3.1.2.15 8.3.2 8.3.3 DPRES-SYNC element definitions for stand-alone M-DM-AUTH 26 Addressing for URT = 00102 . 26 Addressing for URT = 00112 . 26 Addressing for URT = 01002 or 01012 . 26 Addressing for URT = O1 lo2 . 27 Channel state . 27 Ch

15、annel usage . 28 Device address 28 Frequency efficient mode flag . 28 Maximum DM-MS power class . 28 M-DMO flag . 29 MNI of controlling SwMI 29 Number of validity time units 29 Presence signal dual watch synchronization flag 29 Usage restriction type (URT) . 30 Validity time unit 30 DPRES-SYNC PDU f

16、or M-DM-REP . 30 DPRES-SYNC PDU for M-DM-GATE or M-DM-REP/GATEi . 31 Annex A (normative): A.l A.2 Timers and constants specific to M-DMO . 32 Timers and constants in M-DM-MS 32 Timers and constants in M-DM-AUTH . 32 Annex B (normative): Annex C (normative): C.l C.2 Differences for direct MS-MS opera

17、tion . 33 Differences for type 1 repeater operation . 35 Differences for M-DM-MS . 35 Differences for M-DM-REP 35 Annex D (Normative): D.l D.2 Differences for gateway operation . 36 Differences for M-DM-MS . 36 Differences for M-DM-GATE or M-DM-REP/GATE . 36 Annex E (Normative): E.l E.2 Differences

18、for type 2 repeater operation . 37 Differences for M-DM-MS . 37 Differences for M-DM-REP 37 Annex F (normative): Differences for V+D authorized M-DM-MS . 38 History . 39 ETSI 5 ETSI TS 1 O0 396-1 O V1.l.l (2000-1 2) Intellectual Property Rights IPRs essential or potentially essential to the present

19、document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR O00 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respec

20、t of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server -). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referen

21、ced in ETSI SR O00 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Terrestrial Trunked Radio (TETRA). The present document is part 10 of a multi-part deliv

22、rable covering the Technical requirements for Direct Mode Operation (DMO), as identified below: Part 1: Part 2: Part 3: Part 4: Part 5: Part 6: Part 7: Part 8: Part 9: Part 10: General network design; Radio aspects; Mobile Station to Mobile Station (MS-MS) Air Interface (AI) protocol; Type 1 repeate

23、r air interface; Gateway air interface; Security; Type 2 repeater air interface; Protocol Implementation Conformance Statement (PICS) proforma specification; Service and Description Language (SDL) model; Managed Direct Mode Operation (M-DMO). ETSI 6 ETSI TS 1 O0 396-1 O V1.l.l (2000-1 2) 1 Scope TS

24、100 396 defines the Terrestrial Trunked Radio (TETRA) Direct Mode Operation (DMO). It specifies the basic air interface, the inter-working between Direct Mode (DM) groups via repeaters, and inter-working with the TETRA Voice plus Data (V+D) system via gateways. It also specifies the security aspects

25、 in TETRA DMO, and the intrinsic services that are supported in addition to the basic bearer and teleservices. The present document defines TETRA Managed Direct Mode Operation (M-DMO). M-DMO provides a means to restrict the use of Direct Mode Operation (DMO) by requiring prior authorization before a

26、 Direct Mode Mobile Station (DM-MS) is permitted to transmit on a radio frequency. This modifies the operation of DM-MSs from that specified in ETS 300 396-3 3, EN 300 396-4 4, ETS 300 396-5 5 and EN 300 396-7 7. M-DMO provides a control mechanism by which radio frequencies (M-DMO frequencies) may b

27、e given for DMO use for a period of time; those frequencies are considered to be managed frequencies. All M-DMO devices operating on a managed frequency shall comply with the transmit restrictions defined in the present document. An M-DMO DM-MS (M-DM-MS) may receive the authorization to transmit fro

28、m a broadcast signal sent on the M-DMO frequency.Or, alternatively, it may obtain the authorization directly on the V+D side from the SwMI or ftom an M-DMO management station. The authorizing unit which sends the broadcast signal on the M-DMO frequency is referred to as an M-DM-AUTH. It obtains the

29、authorization to operate as an M-DM-AUTH from the V+D SwMI or from a management station that is authorized to allocate frequencies for M-DMO. An M-DM-AUTH may be a stand-alone unit (performing only the authorization function), or it may perform also the function of a DM-REP, DM-GATE or DM-REP/GATE.

30、The content of the present document is as follows: - - - - - Clause 4: provides an overview of M-DMO; Clause 5: describes the procedures for M-DMO mobile stations; Clause 6: describes the procedures for M-DM-AUTHs; Clause 7: describes the operation of M-DMO frequencies; Clause 8: describes the usage

31、 of the authorization presence signal; - - Annex A: lists the timers and constants specific to M-DMO; Annexes B through F: describe the differences from ETS 300 396-3 3, EN 300 396-4 4, ETS 300 396-5 5 and EN 300 396-7 7 arising from M-DMO. The present document assumes familiarity with operation of

32、TETRA in a network environment as described in EN 300 392, and with operation of TETRA in Direct Mode as described in other parts of ETSEN 300 396. The present document does not define the process for deciding which frequencies are allocated to M-DMO use. 2 References The following documents contain

33、 provisions which, through reference in this text, constitute provisions of the present documen t. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specif

34、ic reference, the latest version applies. 111 ETSI ETS 300 396-1: “Terrestrial Trunked Radio (TETRA); Technical Requirements for Direct Mode Operation (DMO); Part 1: General Network Design“. ETSI 7 ETSI TS 1 O0 396-1 O V1.l.l (2000-1 2) 121 ETSI ETS 300 396-2: “Terrestrial Trunked Radio (TETRA); Tec

35、hnical Requirements for Direct Mode Operation (DMO); Part 2: Radio Aspects“. ETSI ETS 300 396-3: “Terrestrial Trunked Radio (TETRA); Technical Requirements for Direct Mode Operation (DMO); Part 3: Mobile Station to Mobile Station (MS-MS) Air Interface (AI) Protocol“. 131 141 ETSI EN 300 396-4: “Terr

36、estrial Trunked Radio (TETRA); Technical Requirements for Direct Mode Operation (DMO); Part 4: Type 1 repeater air interface“. ETSI ETS 300 396-5: “Terrestrial Trunked Radio (TETRA); Technical Requirements for Direct Mode Operation (DMO); Part 5: Gateway air interface“. ETSI ETS 300 396-6: “Terrestr

37、ial Trunked Radio (TETRA); Direct Mode Operation (DMO); Part 6: Security“. 151 161 171 ETSI EN 300 396-7: “Terrestrial Trunked Radio (TETRA); Technical Requirements for Direct Mode Operation (DMO); Part 7: Typeke 2 repeater air interface“. ETSI EN 300 392-2: “Terrestrial Trund Radio (TETRA); Voice p

38、lus Data (V+D); Part 2: Air Interface (AI)“. ETSI TR 101 661: “Terrestrial Trunked Radio (TETRA); Technical Requirements Specification; Managed Direct Mode Operation (DMO)“. 181 191 3 3.1 Definitions and abbreviations Def i n it ions For the purposes of the present document, the following terms and

39、definitions apply: authorization datum point: geographical point in space from which M-DMO is allowed authorization presence signal: message that is transmitted by an M-DM-AUTH on an M-DMO RF carrier. It permits M-DM-MSs which receive this message to know that the M-DM-AUTH is within range. It indic

40、ates which M-DM-MSs are authorized to transmit on the RF carrier, and the validity time for which those M-DM-MSs are authorized call: there are two types of call, individual call or group call. An individual call is a complete sequence of related call transactions between two MSs. There are always t

41、wo participants in an individual call. A group call is a complete sequence of related call transactions involving two or more MSs. The number of participants in a group call is not fixed, but is at least two. Participants may join (late entry) and leave an ongoing call call transaction: all of the f

42、unctions associated with a complete unidirectional transmission of information during a call. A call is made up of one or more call transactions. In a simplex call these call transactions are sequential. changeover: within a call, the process of effecting a transfer of the master role (and hence tra

43、nsmitting MS) at the end of one call transaction so that another can commence Direct Mode Call Control (DMCC): layer 3 entity responsible for setting up and maintaining a call in DMO DM channel: specific grouping of timeslots in the DM multiplex structure related to a particular DM RF carrier i.e. D

44、M frequency (or to a pair of duplex-spaced RF carriers for operation with a type 1B or type 2 DM-REP or a type 1B DM-REP/GATE). The grouping may not always be fixed, but in DMO when operating in fi-equency efficient mode as an example, there are two DM channels, identified by the letters A and B. Di

45、rect Mode Operation (DMO): mode of simplex operation where mobile subscriber radio units may communicate using radio frequencies which may be monitored by, but which are outside the control of, the TETRA V+D network. DM operation is performed without intervention of any base station. direct mode pre

46、sence signal: message that is transmitted by a DM-REP, DM-GATE, DM-REP/GATE or M-DM-AUTH in order to indicate its presence on a DM RF carrier. It permits DM-MSs which receive this message to know that the DM-REP, DM-GATE, DM-REP/GATE or M-DM-AUTH is within range. ETSI 8 ETSI TS 1 O0 396-1 O V1.l.l (

47、2000-1 2) Direct Mode Mobile Station (DM-MS): physical grouping that contains all of the mobile equipment that is used to obtain TETRA DM services. A DM-MS may have one of three roles: - master: if the DM-MS is either active in a call transaction transmitting traffic or control data, or is reserving

48、 the channel by means of channel reservation signalling; slave: if the DM-MS is receiving traffic and/or signalling in a call; or idle: if the DM-MS is not in a call. - - Dual Mode switchable Mobile Station (DU-MS): MS that is capable of both TETRA DMO and TETRA V+D operation. Only one mode can be s

49、elected at any given time and the MS is not capable of monitoring a DM RF carrier while in V+D mode or a V+D channel while in DMO. Dual Watch Mobile Station (DW-MS): MS that is capable of both TETRA DMO and TETRA V+D operation. The MS is capable of periodically monitoring the V+D control channel while in a DM call, a DM RF carrier while in a V+D call and, when idle, it periodically monitors both the DM RF carrier and the V+D control channel. Direct Mode GATEway (DM-GATE): device which provides gateway connectivity between DM-MS(s) and the TETRA V+D network. The gateway