EN ISO 8442-4-1997 en Materials and Articles in Contact with Foodstuffs - Cutlery and Table Holloware - Part 4 Requirements for Gold-Plated Cutlery《与食品接触的材料和制品 刀具与凹形餐具 第4部分 镀金刀具的要求.pdf

《EN ISO 8442-4-1997 en Materials and Articles in Contact with Foodstuffs - Cutlery and Table Holloware - Part 4 Requirements for Gold-Plated Cutlery《与食品接触的材料和制品 刀具与凹形餐具 第4部分 镀金刀具的要求.pdf》由会员分享，可在线阅读，更多相关《EN ISO 8442-4-1997 en Materials and Articles in Contact with Foodstuffs - Cutlery and Table Holloware - Part 4 Requirements for Gold-Plated Cutlery《与食品接触的材料和制品 刀具与凹形餐具 第4部分 镀金刀具的要求.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 STD-BSI BS EN IS0 8442-4-ENGL 1998 II 1624669 08383Y5 360 BRITISH STANDARD Materials and articles in contact with foodstuffs - Cutlery and table holloware - Part 4: Requirements for gold-plated cutlery The European Standard EN IS0 8442-4:1997 incorporating amendment No. 1:1999 has the status of a B

2、ritish Standard ICs 67.250; 97.040.60 NO COPYING WITEIOuT BSI PERMISSION EXCEPT AS PEBMFZTED BY COPYRIGHT LAW BS EN IS0 8442-4:1998 Tncorporating Amendment No. 1 BS EN IS0 8442-41998 direction of the Consumer Amd. No. Products and Services Sector Board, was published under the 10648 authority of the

3、 Standards Board and comes into effect on 15 February 1998 Q BSI 01-2000 National foreword Date Comments January 2000 This British Standard is the English language version of EN IS0 8442-4:1997. It is identical with IS0 8442-2: 1997. The UK participation in its preparation was entrusted to Technical

4、 Committee CW/17, Cutlery and table holloware, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible internationalEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related int

5、ernational and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. The textual errors set out below were discovered when the English language version of EN IS0 8442-4 was adopted as the national stand

6、ard. They have been reported to CEN is a proposal to amend the text of the European Standard. In 5.5 second paragraph delete “inclined” and replace with “included In D.3.3: replace “Connect the test load by “Connect the test load (30N f 1N)” Cross-references Attention is drawn to the fact that CEN a

7、nd CENELEC standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Ca

8、talogue under the section entitled “International Standards Correspondence Index”, or by using the “Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their

9、 correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN IS0 title page, page 2, the IS0 title page, pages ii to iv, pages 1 to 11 and a ba

10、ck cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Sidelining in this document indicates the most recent changes by amendment. ISBN O 580 28812 9 STD-BSI BS EN IS0 8442-4-ENGL 1998 m Lh24h69 0838347 L33 m BS EN IS0 8442-4:1998 Contents National

11、 foreword Page Inside front cover Foreword 2 Foreword 111 Text of IS0 8442-4 1 . O BSI 01-2000 STD-BSI BS EN IS0 8442-4-ENGL 1998 m 3b24bb9 0818348 0iT m EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 8442-4 December 1997 ICs 67 250; 97.040.60 Descriptors: See IS0 document English version

12、Materials and articles in contact with foodstuffs - Cutlery and table holloware - Part 4: Requirements for gold-plated cutlery (IS0 8442-41997) Matriaux et objets en contact avec les denres alimentaires - Coutellerie et orfvrerie de table - Partie 4: Exigences relatives la coutellerie et aux couvert

13、s dors Werkstoffe und Gegenstnde in Kontakt mit Lebensmitteln - Schneidwaren und Tafelgerte - Teil 4: Anforderungen fr vergoldete Bestecke (IS0 8442-4: 1997) (IS0 8442-4: 1997) This European Standard was approved by CEN on 11 October 1997. CEN members are bound to comply with the CENXENELEC Internal

14、 Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. T

15、his European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are

16、the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation E

17、uropisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN IS0 8442-4:1997 E Fore word The text of EN IS0 8442-4:1997 has been prepared by Technical

18、 Committee CEN/TC 194 “Utensils in contact with food”, the secretariat of which is held by BSI, in collaboration with Technical Committee ISO/TC 186 “Cutlery and table and decorative metal hollow-ware”. This European Standard shall be given the status of a national standard, either by publication of

19、 an identical text or by endorsement, at the latest by June 1998, and conflicting national standards shall be withdrawn at the latest by June 1998. EN IS0 8442 consists of the following parts: -Part 1: Requirements for cutlery for the preparation of food; -Part 2: Requirements for stainless steel an

20、d silver-plated cutlery; -Part 3: Requirements for silver-plated table and decorative holloware; -Part 4: Requirements for gold-plated cutlery. Further parts are proposed with the following titles: -Part 5: Specific cutting test; -Part 6: Lacquered lightly silver-plated table and decorative hollowar

21、e; -Part 7: Specification for table cutlery made of precious metals and their alloys, especially silver cutlery; -Part 8: Specification for silver table and decorative holloware. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bou

22、nd to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Q BSI 05-1999 2 EN IS0 8442-4 : 1997 INTERNATIONAL STANDARD IS0 8

23、442-4 First edition 1997-1 2-1 5 Corrected 1998-01-15 Materials and articles in contact with foodstuffs - Cutlery and table holloware - Part 4: Requirements for gold-plated cutlery Matriaux et objets en contact avec les denres alimentaires - Coutellerie er orfvrerie de table - Partie 4: Exigences re

24、latives la coutellerie et aux couverts dors Reference number IS0 8442-4:1997(E) EN IS0 8442-4:1997 1 Contents Foreword Introduction 1 Scope 2 Normative references 3 Definitions 4 Materials and their application 5 Construction 6 Gold plated cutlery 7 Performance requirements 8 Marking and labelling A

25、nnex A (normative) Test method for average thickness of gold coating Annex B (normative) Schlegel method of determining surface area Annex C (normative) Test method for corrosion resistance of unplated steel cutlery Annex D (normative) Test method for strength of knives with martensitic stainless st

26、eel blades and carving forks Annex E (normative) Test method for adhesion of gold coatings Annex F (informative) A-Deviations Annex G (informative) Bibliography Figure 1 - Strength test for a spoon Figure C. 1 - Apparatus for corrosion test Figure D. 1 - Strength test apparatus for knives Figure D.2

27、 - Determination of angle of permanent deformation Table 1 - Metals for table cutlery, compositions limit Table 2 - Average thickness of classes of gold coating I Page 1 1 1 1 1 1 3 3 4 . 111 6 6 7 9 10 11 11 4 8 9 10 2 3 O BSI 01-2000 STD-BSI BS EN IS0 8442-4-ENGL 1998 3624669 0838352 5T0 E EN IS0

28、8442-4:1997 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject f

29、or which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on

30、 all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard

31、IS0 8442-4 was prepared by the European Committee for Standardization (CEN) in collaboration with IS0 Technical Committee TC 186, Cutlery and table and decorative metal hollow-ware, in accordance with the Agreement on technical cooperation between IS0 and CEN (Vienna Agreement). IS0 8442 consists of

32、 the following parts, under the general title Materials and articles in contact with foodstuffs - Cutlery and table holloware: -Part 1: Requirements for cutlery for the preparation of food; - Part 2: Requirements for stainless steel and silver-plated cutlery; - Part 3: Requirements for silver-plated

33、 table and decorative holloware; - Part 4: Requirements for gold-plated cutlery. Further parts are proposed with the following titles: -Part 5: Specific cutting test; - Part 6: Lacquered lightly silver-plated table and decorative holloware; - Part 7: Specification for table cutlery made of precious

34、metals and their alloys, especially silver cutlery; - Part 8: Specification for silver table and decorative holloware. Annex A to Annex E form an integral part of this part of IS0 8442. Annex G is for information only. Descriptors: Tableware, flatware, gold plating, cutlery, specifications, material

35、s specifications, performance, tests, performance tests, marking, labelling. O BSI 01-2000 . 111 - STD-BSI BS EN IS0 8442-4-ENGL 3998 = Lb24bb9 0838353 137 II EN IS0 8442-41997 Introduction This Standard does not cover those features of cutlery which are matters of personal choice for the user: such

36、 as the design, size, type of finish, blade flexibility or similar characteristics which can be readily identified by the purchaser at the point of sale. Attention is drawn to Directives of the European Community concerning materials and articles in contact with food, in particular to Directives EC

37、89/109 and EC 90/128. 1 Scope This Standard specifies the following requirements for gold plated cutlery: a) performance requirements for table cutlery (for example, knives, forks, spoons, carving sets, ladles, and other serving pieces); b) composition limits for base metals for cutlery; c) tests fo

38、r resistance to permanent deformation, firmness of handle attachment, hardness of blades, resistance to corrosion and the thickness and adhesion of gold coatings; d) three minimum thicknesses of gold plating: a first class, a second class, and a third class. This Standard specifies the method of def

39、ining gold deposits for each and every item and also test methods. This Standard does not apply to table cutlery which has only small areas of gold plate as inlays in non gold plated decoration. 2 Normative references This Standard incorporates by dated or undated reference, provisions from other pu

40、blications. These normative references are cited at the appropriate places in the text. and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this Standard only when incorporated in it by amendment or revision. Fo

41、r undated references the latest edition of the publication referred to applies. IS0 1463, Metallic and oxide coatings - Measurement of coating thickness - Microscopical method. IS0 2177, Metallic coatings - Measurement of coating th.ickness - Coulometric method by anodic dissolution. IS0 3497. Metal

42、lic coatings - Measurement of coating ih ickness - X-ray spectrometric methods. IS0 3543, Metallic and non-metallic coatings - Measurement of thickness - Beta scatter method. IS0 4481:1977, Cutlery and flatware - Nomenclature. IS0 6508:1986, Metallic materials - Hardness test - Rockwell test (scales

43、 A - B - C - D - E - F - EN IS0 8442-2, Materials and articles in contact with foodstuffs - Cutlery and table holloware - Part 2: Requirements for stainless steel and silver plated cutlery (IS0 8442-2:1997). 3 Definitions For the purposes of this Standard the definitions given in IS0 448111977 and E

44、N IS0 8442-2 apply together with the following. 3.1 hard gold plating refined gold plating containing elements which increase the hardness G-H-K). 4 Materials and their application 4.1 General The cutlery shall be made from materials that enable the finished product to meet all of the performance re

45、quirements of this standard. NOTE The cutlery should not under foreseeable conditions of use transfer any substance likely to be detrimental to health or to have any detrimental organoleptic effects. 4.2 Metals 4.2.1 The composition of metal parts of table cutlery shall be as given in Table 1. 4.2.2

46、 All gold plated parts of table cutlery shall be in accordance with the requirements of clause 6. 5 Construction 5.1 General Cutlery manufactured from the materials specified in clause 4 shall be so constructed that it meets all the relevant performance requirements of this standard. 5.2 Alignment,

47、uniformity and absence of defects 5.2.1 All surfaces shall be free from cracks, pits and other defects. 5.2.2 All cutlery shall be essentially straight and symmetrical except when the lack of straightness or symmetry is an intentional feature of the design. 5.2.3 Identical items within a batch shall

48、 show no variation in dimension or form. 5.2.4 All edges, including the edges of spoons, forks, ladles and the insiders of fork prongs, shall be free from burrs and the roughness of blanked edges shall have been removed by a suitable operation. O BSI 01-2000 1 STD-BSI BS EN IS0 8442-4-ENGL 1998 3624

49、669 0818354 373 111 EN IS0 8442-4:1997 O O CJ, - O 3 u3 8 n s B O 3 a, % x E E O O m R I+ E u3 rl 8 O 0 n O - E Co 4 0- O BSI 01-2000 2 - - STDOES1 BS EN IS0 8442-4-ENGL 1998 1624bb9 0818355 20T E EN IS0 8442-41997 Description First class 5.2.5 Table knives shall be balanced such that when the knife is pivoted on its bolster, or at the junction of the handle and blade if no bolster is present, the handle shall be heavier than the blade. 5.2.6 Compliance with the requirements for 5.2.1 to 5.2.5 shall be checked by tou