ARMY MIL-PRF-63002 L-2013 MANUALS TECHNICAL REQUIREMENTS FOR PREPARATION OF MODIFICATION WORK ORDERS (MWOs).pdf

《ARMY MIL-PRF-63002 L-2013 MANUALS TECHNICAL REQUIREMENTS FOR PREPARATION OF MODIFICATION WORK ORDERS (MWOs).pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-PRF-63002 L-2013 MANUALS TECHNICAL REQUIREMENTS FOR PREPARATION OF MODIFICATION WORK ORDERS (MWOs).pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC 9366 AREA TMSS DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. NOT MEASUREMENT SENSITIVE MIL-PRF-63002L (TM) 29 APRIL 2013 SUPERSEDING MIL-PRF-63002K (TM) 18 May 2009 PERFORMANCE SPECIFICATION MANUALS, TECHNICAL: REQUIREMENTS FOR PREPARATION OF MODIFICATION WOR

2、K ORDERS (MWOs) This specification is approved for use by the Department of the Army and is available for use by all departments and agencies of the Department of Defense. Comments, suggestions, or questions on this document should be addressed to: Commander, USAMC Logistics Support Activity, Logist

3、ics Engineering Center, ATTN: AMXLS-AP, Redstone Arsenal, AL 35898-7466 or e-mailed to usarmy.redstone.logsa.mbx.tmssmail.mil. Since contact information can change, you may want to verify the currency of this address using the ASSIST Online database at http:/assist.dla.mil/. Provided by IHSNot for R

4、esaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63002L(TM) ii This page intentionally left blank. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63002L(TM) TABLE OF CONTENTS PARAGRAPH PAGE iii 1. SCOPE .1 2.

5、 APPLICABLE DOCUMENTS.1 2.1 General. 1 2.2 Government documents. 1 2.2.1 Specifications, standards, and handbooks. .1 2.2.2 Other Government documents, drawings, and publications. .1 2.3 Order of precedence. 2 3. REQUIREMENTS .2 3.1 General Style and Format 2 3.1.1 Paragraphs. .2 3.1.1.1 Primary par

6、agraphs. .2 3.1.1.2 Subordinate paragraphs. .3 3.1.2 Figure and table. .4 3.2 Content .4 3.2.1 Front matter. .4 3.2.1.1 Cover/title page . .4 3.2.1.1.1 Security Classification .5 3.2.1.1.2 MWO Priority 5 3.2.1.1.3 MWO effective date/completion date statement 5 3.2.1.1.4 MWO Number .5 3.2.1.1.5 MWO T

7、itle .5 3.2.1.1.6 National Stock Number (NSN) 5 3.2.1.1.7 End Item Code (EIC) .5 3.2.1.1.8 Authentication statement .5 3.2.1.1.9 MWO Date .5 3.2.1.1.10 Reporting errors and recommending improvements. .6 3.2.1.1.10.1 Reporting errors and recommending improvements in ROUTINE MWOs . .6 3.2.1.1.10.2 Rep

8、orting errors and recommending improvements in URGENT and EMERGENCY MWOs 6 3.2.1.1.11 Availability statement . 6 3.2.1.1.12 Distribution statement . 6 3.2.1.1.13 Export control warning notice . .6 3.2.1.1.14 Destruction Notice . .7 3.2.1.1.15 Copyright notice . 7 3.2.1.1.16 Supersedure Notice 7 3.2.

9、2 MWO body. .7 3.2.2.1 Text. .7 3.2.2.2 Content of standard paragraphs. 8 3.2.2.2.1 Paragraph 1 Purpose . 8 3.2.2.2.2 Paragraph 2 Priority . 8 3.2.2.2.3 Paragraph 3 End item(s) or system(s) to be modified . 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

10、HS-,-,-MIL-PRF-63002L(TM) TABLE OF CONTENTS PARAGRAPH PAGE iv 3.2.2.2.4 Paragraph 4 Module(s) (components, assemblies, subassemblies, boards, and cards) to be modified . 8 3.2.2.2.5 Paragraph 5 Part(s) to be modified . .8 3.2.2.2.6 Paragraph 6 Application . .8 3.2.2.2.7 Paragraph 7 Technical publica

11、tions affected/changed . 9 3.2.2.2.8 Paragraph 8 MWO kit(s)/part(s) and their disposition . .9 3.2.2.2.9 Paragraph 9 Special tools; tool kits; jigs; test, measurement, and diagnostic equipment (TMDE); and fixtures required . 9 3.2.2.2.10 Paragraph 10 Modification procedures . 10 3.2.2.2.11 Paragraph

12、 11 Calibration requirements . 10 3.2.2.2.12 Paragraph 12 Weight and balance data . .10 3.2.2.2.13 Paragraph 13 Quality assurance requirement . 11 3.2.2.2.14 Paragraph 14 Recording and reporting of the modification . .11 3.2.2.2.15 Paragraph 15 Material Change Number (MCN) . .11 3.2.2.2.16 Paragraph

13、 16 Modification identification . 11 3.2.3 Appendixes . .12 3.2.4 Rear matter . 12 3.2.4.1 DA Form 2028 . .12 3.2.4.2 Authentication . .12 3.2.4.3 Foldout section . 12 3.2.5 Abbreviated MWO (Short Form). 12 4. VERIFICATION 12 4.1 Verification. .12 5. PACKAGING .12 5.1 Packaging. 12 6. NOTES .13 6.1

14、Intended use. 13 6.2 Acquisition requirements. 13 6.2.1 Technical Manuals (TMs). .13 6.2.2 Document Type Definition (DTD). .13 6.3 Definitions13 6.3.1 Abbreviated MWO (Short Form). 13 6.3.2 Acquiring Activity. 13 6.3.3 Depot Maintenance Work Requirement (DMWR). .14 6.3.4 Emergency. 14 6.3.5 Modifica

15、tion Work Order (MWO). .14 6.3.6 Routine. 14 6.3.7 Urgent. .14 6.4 Subject term (keyword) listing.14 6.5 Changes from previous issue. 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63002L(TM) TABLE OF CONTENTS PARAGRAPH PAGE v A CONTENT/F

16、ORMAT SELECTION MATRIX .23 A.1 SCOPE .23 A.1.1 Scope. .23 A.2 APPLICABLE DOCUMENTS 23 A.3 REQUIREMENTS .23 A.3.1 Application .23 A.3.2 Explanation of columns in TABLE A-I Content Matrix for MWO 23 B DTD USE AND ACCESS 27 B.1 SCOPE 27 B.1.1 Scope 27 B.2 APPLICABLE DOCUMENTS 27 B.3 REQUIREMENTS .27 B.

17、3.1 Use of the DTDs/Stylesheets .27 B.3.2 Obtaining the DTDs/Stylesheets 27 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63002L(TM) vi Figure Page FIGURE 1. Paragraph numbering and formatting example. . 15 FIGURE 2. Example of a new comman

18、d-authenticated ROUTINE MWO. . 16 FIGURE 3. Example of a new command-authenticated URGENT MWO. 17 FIGURE 4. Example of a new command-authenticated EMERGENCY MWO. 18 FIGURE 5. Example of a new DA-authenticated MWO. . 19 FIGURE 6. Example of a revised command-authenticated MWO.20 FIGURE 7. Sample comp

19、utation and format for presentation of work force and man-hour requirements21 FIGURE 8. Examples of Authentication Blocks. 22 Table Page TABLE A-1 Content Matrix for MWO 25 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63002L(TM) 1 1. SCOPE

20、. This specification contains the requirements for the preparation of Modification Work Orders (MWOs). 2. APPLICABLE DOCUMENTS. 2.1 General. The documents listed in this section are specified in section 3 of this specification. This section does not include documents cited in other sections of this

21、specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in section 3 of this specification, whether or not they are li

22、sted. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or co

23、ntract. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-40051-1 Preparation of Digital Technical Information for Interactive Electronic Technical Manuals (IETMs) MIL-STD-40051-2 Preparation of Digital Technical Information for Page-Based Technical Manuals (Copies of the above standards are available online

24、at http:/assist.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to

25、the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AR 25-30 The Army Publishing Program AR 95-1 Flight Regulations AR 750-10 Army Modification Program DA PAM 25-40 Army Publishing: Action Officers Guide DA PAM 738-7

26、51 Functional Users Manual for the Army Maintenance Management System-Aviation (TAMMS-A) DA PAM 750-8 The Army Maintenance Management System (TAMMS) Users Manual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63002L(TM) 2 TM 55-1500-342-23 J

27、oint Service Technical Manual for Aircraft Weight and Balance TM 750-245-4 Direct Support and General Support for Quality Control Inspectors Inspection Criteria (Copies of the above publications are available from the U.S. Army Publishing Directorate, Media Distribution Division, ATTN: JDHQSV-PAS, 1

28、655 Woodson Rd., St. Louis, MO 63114-6181. Electronic copies of ARs and DA PAMs are available online at www.apd.army.mil. Electronic copies of TMs are available online at https:/www.logsa.army.mil.) DODM 5200.01, Volume 1 Information Security Program: Overview, Classification, and Declassification D

29、ODM 5200.01, Volume 2 Information Security Program: Marking of Classified Information DODM 5200.01, Volume 3 Information Security Program: Protection of Classified Information DODM 5200.01, Volume 4 Information Security Program: Controlled Unclassified Information (CUI) DODI 5230.24 Distribution Sta

30、tements on Technical Documents DODD 5230.25 Withholding of Unclassified Technical Data from Public Disclosure (Copies of DOD documents are available at http:/www.dtic.mil/whs/directives/.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between t

31、he text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS. 3.1 General style and format. The general style and form

32、at of MWOs shall be in accordance with MIL-STD-40051-2 and this specification. MWO may be developed as an Interactive Electronic MWO. If so, general style and format and look and feel requirements in MIL-STD-40051-1 shall be followed. 3.1.1 Paragraphs. Text shall be divided into paragraphs and proce

33、dural steps. Procedural steps may be further divided if necessary. Paragraph numbering and formatting as described in 3.1.1.1 and 3.1.1.2 shall be used. See FIGURE 1 for an example. 3.1.1.1 Primary paragraphs. Primary paragraphs shall have a sidehead. The sixteen primary sideheads (see 3.2.2.1) shal

34、l be numbered consecutively using Arabic numbers. Primary sideheads stand alone (are not run in with text) and shall be flush left. They shall appear bold and uppercased. Primary paragraph text shall begin on the next line immediately below the paragraph title and shall be flush left. Provided by IH

35、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63002L(TM) 3 3.1.1.2 Subordinate paragraphs. There shall be no more than six levels of subparagraphs. There shall be at least two subparagraphs at any level (e.g., if you have a you must at least have b, if y

36、ou have (1) you must at least have (2), etc.). Subordinate paragraphs, procedures, and steps shall be numbered and formatted as follows: a. First level paragraph, shall be numbered and have a title. The number shall be indented under the first word of text in primary paragraph and be lower case alph

37、abetic character(s) followed by a period (e.g., “a.”). The title shall be in title case and shall be bold and shall be followed by a period. The text shall begin on the same line as the title indented two spaces after the period. The text shall have a hanging indent that begins the wrapped text dire

38、ctly under the beginning of the text of the first line. If paragraph numbering extends beyond the letter “z,” numbering shall continue using “aa.,” “ab.,” “az.” then go to “ba.,” “bb.,” etc. Should numbering go to double letters, the number position shall be right justified to maintain a consistent

39、indent of the text. b. Second level paragraph or step shall be numbered with an Arabic number enclosed in parentheses (e.g., “(1)”). The number shall be indented under the first word of the first level subparagraph. A title is optional. If a title is given, the title shall be in title case and shall

40、 be bold and shall be followed by a period. The text shall begin on the same line as the title indented two spaces after the period. If no title is given, text shall begin two spaces following the right parenthesis. The paragraph or step shall have a hanging indent that begins the wrapped text direc

41、tly under the beginning of the text of the first line. For double digit numbering, the number position shall be right justified to maintain a consistent indent of the text. c. Third level paragraph or step shall be numbered with a lower case alphabetic characters(s) enclosed in parentheses (e.g., “(

42、a)”). The number shall be indented under the first word of the second level subparagraph. A title is optional. If a title is given, the title shall be in title case and shall be bold and shall be followed by a period. The text shall begin on the same line as the title indented two spaces after the p

43、eriod. If no title is given, text shall begin two spaces following the right parenthesis. The paragraph or step shall have a hanging indent that begins the wrapped text directly under the beginning of the text of the first line. The same criteria as for first level numbering shall be used. d. Fourth

44、 level paragraph or step shall be numbered with an underscored Arabic number followed by a period (e.g., “1.”). The number shall be indented under the first word of the third level subparagraph. A title is optional. If a title is given, the title shall be in title case and shall be bold and shall be

45、 followed by a period. The text shall begin on the same line as the title indented two spaces after the period. If no title is given, text shall begin two spaces following the period. The paragraph or step shall have a hanging indent that begins the wrapped text directly under the beginning of the t

46、ext of the first line. The same criteria as for second level numbering shall be used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63002L(TM) 4 e. Fifth level paragraph or step shall be numbered with an underscored lower case alphabetic ch

47、aracter(s) followed by a period (e.g., “a.”). The number shall be indented under the first word of the fourth level subparagraph. A title is optional. If a title is given, the title shall be in title case and shall be bold and shall be followed by a period. The text shall begin on the same line as t

48、he title indented two spaces after the period. If no title is given, text shall begin two spaces following the period. The paragraph or step shall have a hanging indent that begins the wrapped text directly under the beginning of the text of the first line. The same criteria as for first level numbering shall be used. f. Sixth level paragraph or step shall be numbered with a lower case roman numeral followed by a period (e.g