EN 15939-2011 en Hardware for furniture - Strength and loading capacity of wall attachment devices (Incorporates Amendment A1 2014)《五金家具 墙附件设备的强度和载荷能力》.pdf

《EN 15939-2011 en Hardware for furniture - Strength and loading capacity of wall attachment devices (Incorporates Amendment A1 2014)《五金家具 墙附件设备的强度和载荷能力》.pdf》由会员分享，可在线阅读，更多相关《EN 15939-2011 en Hardware for furniture - Strength and loading capacity of wall attachment devices (Incorporates Amendment A1 2014)《五金家具 墙附件设备的强度和载荷能力》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationHardware for furniture Strength and loading capacityof wall attachment devicesBS EN 15939:2011+A1:2014BS EN 15939:2011+A1:2014National forewordThis British Standard is the UK implementation of EN 15939:2011+A1:2014. It supersedes BS EN 15939:2011, which is withdrawn.The star

2、t and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“.The UK participation in its preparation was entrusted by Technical Com

3、mittee FW/0, Furniture, to Subcommittee FW/0/1, Common Test Methods for Furniture.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for it

4、s correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014ISBN 978 0 580 82575 0ICS 97.140Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the Standards Policy and St

5、rategy Committee on 31 January 2012.Amendments/corrigenda issued since publicationDate Text affected31 March 2014 Implementation of CEN amendment A1:2014BRITISH STANDARDEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15939:2011+A1 January 2014 ICS 97.140 English Version Hardware for furniture -

6、 Strength and loading capacity of wall attachment devices Quincaillerie dameublement - Rsistance mcanique et capacit de charge des dispositifs de fixation au mur Mbelbeschlge - Festigkeit und Tragfhigkeit von Schrankaufhngern This European Standard was approved by CEN on 12 November 2011 and include

7、s Amendment 1 approved by CEN on 14 December 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references conc

8、erning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member in

9、to its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,

10、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITE

11、E FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15939:2011+A1:2014 E2 Contents PageForeword 3 1 Scope 4 2 Normative references 4 3 Terms and definit

12、ions .5 4 General test condition .5 4.1 Preliminary preparation 5 4.2 Test equipment 5 4.2.1 Test wall 5 4.2.2 Particle board properties 6 4.2.3 Fibre board properties 6 4.2.4 Steel impact plate 6 4.2.5 Dowels 6 4.2.6 Nails 6 4.2.7 Distance devices 6 4.2.8 Non-commercial wall part .6 4.3 Application

13、 of forces .7 4.4 Tolerances 7 5 Test frame .7 6 Test procedures and requirements . 13 6.1 General . 13 6.2 Verification of loading capacity . 14 6.2.1 Requirements 14 6.2.2 Static load test 14 6.2.3 Impact test . 14 6.2.4 Door swing test . 15 6.2.5 Overload test . 16 6.3 Corrosion resistance 16 7 T

14、est report . 16 Annex A (normative) Product information system . 17 A.1 General . 17 A.2 Loading capacity. 17 A.3 Adjustment systems . 17 A.4 Corrosion test . 17 A.5 Mounting instructions 17 Annex B (informative) Determination of loading capacity . 18 B.1 Determination of breaking load . 18 B.2 Calc

15、ulation of loading capacity, M 19 Bibliography . 20 BS EN 15939:2011+A1:2014EN 15939:2011+A1:2014 (E)3 Foreword This document (EN 15939:2011+A1:2014) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the st

16、atus of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2014, and conflicting national standards shall be withdrawn at the latest by August 2014. Attention is drawn to the possibility that some of the elements of this document may be the sub

17、ject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 15939:2011. This document includes Amendment 1, approved by CEN on 2013-12-14. The start and finish of text introduced or altered by amendment is indicat

18、ed in the text by tags !“. !According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republ

19、ic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.“ BS EN 15939:2011+A1:2014 EN 15939:2011+A1:2014 (E)4 1 Scop

20、e This European Standard specifies test methods for the verification of the loading capacity of all types of wall attachment devices for storage furniture and their components for all fields of application. It does not apply to devices intended to prevent the overturning of storage furniture. The te

21、sts consist of the application of loads and forces simulating normal functional use, as well as misuse that might reasonably be expected to occur. With the exception of the corrosion test in 6.3, the tests are designed to evaluate properties without regard to materials, design/construction or manufa

22、cturing processes. The tests can be applied to the part attached to the furniture alone or to the combination of the part attached to the furniture and the part attached to the wall. The attachment into the wall is not included. The strength tests are carried out in a test frame with specified prope

23、rties. The test results are only valid for the devices tested. These results may be used to represent the performance of production models provided that the tested model is representative of the production model. With the exception of the corrosion test, ageing and influences of temperature and humi

24、dity are not included. Annex A (normative) includes requirements for product information. Annex B (informative) includes a method for the determination of loading capacity. 2 Normative references !The following documents, in whole or in part, are normatively referenced in this document and are indis

25、pensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.“ EN 310, Wood-based panels Determination of modulus of elasticity in bending and of bending strength EN 319, P

26、articleboards and fibreboards Determination of tensile strength perpendicular to the plane of the board EN 320, Particleboards and fibreboards Determination of resistance to axial withdrawal of screws EN 323, Wood-based panels Determination of density EN 10025-2:2004, Hot rolled products of structur

27、al steels Part 2: Technical delivery conditions for non-alloy structural steels EN 10230-1, Steel wire nails Part 1: Loose nails for general applications EN 10305-5, Steel tubes for precision applications Technical delivery conditions Part 5: Welded cold sized square and rectangular tubes EN ISO 627

28、0-2, Paints and varnishes Determination of resistance to humidity Part 2: Procedure for exposing test specimens in condensation-water atmospheres ISO 7619-2, Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 2: IRHD pocket meter method BS EN 15939:2011+A1:2014 EN 15939:2

29、011+A1:2014 (E)5 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 loading capacity M mass in kg, as specified by the manufacturer, for which one wall attachment device will fulfil the strength requirements specified in this standard NOTE A tes

30、t method for the determination of the loading capacity is described in Annex B (informative). 3.2 wall attachment device device including the component that is attached to the cabinet (e.g. suspension bracket) and the component that is attached to the wall (e.g. hook, rail) 3.3 non-commercial wall p

31、art piece of test equipment specified in 4.2.8 4 General test condition 4.1 Preliminary preparation The wall attachment device(s) shall be mounted according to the instructions supplied with them. The most adverse configuration shall be used and the mounting or assembly method shall be recorded in t

32、he test report. If mounting or assembly instructions are not supplied, the most adverse configuration shall be used and the mounting or assembly method shall be recorded in the test report. The fixing to the wall shall be of such strength that the test result is not influenced. Fittings shall be tig

33、htened before testing and shall not be re-tightened unless specifically required in the manufacturers instructions. If the configuration is to be changed to produce the worst-case conditions, this shall be recorded in the test report. For testing a range of related wall attachment devices, only wors

34、t case(s) need to be tested. The tests shall be carried out in indoor ambient conditions at a temperature between 15 C and 25 C. If during a test the temperature is outside of the range of 15 C to 25 C, the maximum and/or minimum temperature shall be recorded in the test report. Wall attachment devi

35、ces which include structural hardware parts made of hygroscopic plastic materials, e.g. polyamide shall be conditioned at (23 5) C and a relative humidity of (50 5) % for at least seven days before testing. Before beginning the testing, visually inspect the wall hanging device(s) thoroughly. Record

36、any defects so that they are not assumed to have been caused by the tests. Carry out measurements when specified. 4.2 Test equipment 4.2.1 Test wall A rigid, vertical and flat surface which is so constructed that the deformation under the applied load is no more than 1 mm. BS EN 15939:2011+A1:2014 E

37、N 15939:2011+A1:2014 (E)6 4.2.2 Particle board properties The properties of the particle board shall be as specified in Table 1. The thickness tolerance shall be 0,3 mm. Table 1 Particle board properties Property Referenced standard Requirement Axial withdrawal of screws EN 320 (1 100 100) N Density

38、 EN 323 (0,65 0,05) g/cm3 4.2.3 Fibre board properties The properties of the fibre board shall be as specified in Table 2. The thickness shall be 3,2 mm 0,3 mm. Table 2 Fibreboard properties Property Reference standard Requirement Cross tensile strength EN 319 0,5 N/mm2Bending strength EN 310 30 N/m

39、m24.2.4 Steel impact plate A 1,7 kg steel impact plate 200 mm 109 mm 10 mm faced with a 3 mm thick layer of rubber with a hardness of (85 10) IRHD according to ISO 7619-2. 4.2.5 Dowels Round dowels with a diameter of (8 0,1) mm, 30 mm in length, made of beech without any grooves. 4.2.6 Nails 2 mm 30

40、 mm steel wire nails according to EN 10230-1. 4.2.7 Distance devices 50 mm 50 mm with a smooth melamine surface. NOTE Usually a piece of melamine faced particleboard is used. 4.2.8 Non-commercial wall part The non-commercial wall part (see Figure 1) shall be milled out of steel EN 10025-2:2004 S235J

41、R. BS EN 15939:2011+A1:2014 EN 15939:2011+A1:2014 (E)7 Dimensions in millimetres Tolerances: 0,5 mm of the nominal dimensions, unless otherwise stated ! Figure 1 Non-commercial wall part “ 4.3 Application of forces The forces in the load tests shall be applied sufficiently slowly to ensure that negl

42、igible dynamic force is applied. The forces may be replaced by masses. The relation 10 N = 1 kg shall be used for this purpose. 4.4 Tolerances Unless otherwise stated, the following tolerances are applicable: Forces: 5 % of the nominal force; Masses: 1 % of the nominal mass; Dimensions: 1 mm of the

43、nominal dimension; Angles: 2 of the nominal angle. NOTE For the purposes of uncertainty measurement, test results are not considered to be adversely affected when the above tolerances are met. 5 Test frame Depending on the type of wall attachment device to be tested, there are two different test fra

44、mes (A and B), see Figure 2. The test frames (see Figure 2) shall be made as follows: a) the steel frame shall be made of square, hollow components (30 mm 30 mm 1,5 mm) according to EN 10305-5; BS EN 15939:2011+A1:2014 EN 15939:2011+A1:2014 (E)8 b) the pivoting arm, 600 mm in length, shall be a squa

45、re, hollow component (30 mm 30 mm 1,5 mm) according to EN 10305-5; c) !the bottom panel shall be reference particle board, thickness 22 mm 0,3 mm (see Table 1); for test frame B, the bottom panel consists of two parts“; d) the side panels for frame A and B shall be manufactured according to Figure 4

46、 out of reference particle board (see Table 1), thickness 16 mm 0,3 mm; they shall be with a groove for the back panel; e) the top panels for frame A and B shall be manufactured according to Figure 3 out of reference particle board (see Table 1), thickness 16 mm 0,3 mm; f) the back panel, 250 mm 517

47、 mm, shall be out of reference fibreboard (see Table 2), thickness 3,2 mm 0,3 mm. The steel frame shall be welded together all around all cross sections. The top panel (see Figure 3) shall be jointed to the sides using wooden dowels (4.2.5) without the use of glue. The side panels (see Figure 4) sha

48、ll be fixed to the steel frame in a manner so that the deformation of the side panels in relation to the steel frame under the applied load is no more than 1 mm. The back panel shall be nailed with nails (4.2.6) every 100 mm (see Figure 2). Dimensions in millimetres a) Test frame A (with dimensions

49、600 mm 300 mm 1 000 mm) BS EN 15939:2011+A1:2014 EN 15939:2011+A1:2014 (E)9 Dimensions in millimetres Dimensions, keys and witness lines as in Figure 2 a), unless otherwise stated b) Test frame B (with dimensions 600 mm 600 mm 300 mm) Key 1 wall attachment devices 2 top panel 3 pivoting arm 4 side panel 5 bottom panel 6 test frame according to 5 a) 7 back panel 8 nail positions NOTE Test frame type A vertical load is dominating; test frame type B horizontal load is