EN 3094-2017 en Aerospace series - Sealants - Test method - determination of the application time.pdf

《EN 3094-2017 en Aerospace series - Sealants - Test method - determination of the application time.pdf》由会员分享，可在线阅读，更多相关《EN 3094-2017 en Aerospace series - Sealants - Test method - determination of the application time.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Aerospace series - Sealants - Test method - determination of the application timeBS EN 3094:2017EUROPEANSTANDARDNORME EUROPENNE EUROPISCHE NORMEN 3094 October 2017ICS 49.025.99EnglishVersionAerospace series - Sealants -

2、 Test method - determination of the application time Srie arospatiale - Produits dtanchit - Mthode dessai - Dtermination du temps dapplicationLuft- und Raumfahrt - Dichtmassen - Prfverfahren -Bestimmung der VerarbeitungszeitThis European Standard was approved by CEN on 26 June 2017.CEN members are b

3、ound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thisEuropean Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical referencesconcerning such national standards may be obtained on application to the CE

4、N-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made bytranslation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC ManagementCentre has

5、 the same status as the officialversions.CEN members are the nationalstandards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb

6、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Bru

7、ssels 2017 CEN All rights of exploitation in any form and by any means reservedworldwide for CENnational Members.Ref. No. EN 3094:2017 ENational forewordThis British Standard is the UK implementation of EN 3094:2017.The UK participation in its preparation was entrusted to Technical Committee ACE/61/

8、-/6, Mechanical Testing of Metallic Materials for Aerospace Purposes.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applic

9、ation. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 98818 9ICS 49.025.99Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Commit

10、tee on 30 November 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 3094:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3094 October 2017 ICS 49.025.99 English Version Aerospace series - Sealants - Test method - determination of the application tim

11、e Srie arospatiale - Produits dtanchit - Mthode dessai - Dtermination du temps dapplication Luft- und Raumfahrt - Dichtmassen - Prfverfahren - Bestimmung der Verarbeitungszeit This European Standard was approved by CEN on 26 June 2017. CEN members are bound to comply with the CEN/CENELEC Internal Re

12、gulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN me

13、mber. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

14、 CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Polan

15、d, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploi

16、tation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3094:2017 EBS EN 3094:2017EN 3094:2017 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Principle of the test method 4 5 Method A (viscosity) 4 6 Metho

17、d B (extrusion). 5 7 Designation . 6 8 Test report . 6 BS EN 3094:2017EN 3094:2017 (E) 3 European foreword This document (EN 3094:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance wi

18、th the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an iden

19、tical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be withdrawn at the latest by April 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for id

20、entifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yu

21、goslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 3094:2017EN 3094:2017 (E) 4 1 Sc

22、ope This European Standard specifies two methods for the determination of the application time of sealants. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the editi

23、on cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2555:1989, Plastics Resins in the liquid state or as emulsions or dispersions Determination of apparent viscosity by the Brookfield Test method 3 Terms and definitions For

24、the purposes of this document, the following terms and definitions apply. 3.1 application time application time is the time interval, at a specified temperature and humidity, between the mixing of the base material with the curing system and the point where the sealant has cured to a state where app

25、lication by normal methods is no longer possible 4 Principle of the test method The application time is determined by two different methods, depending on the viscosity of the sealant. 4.1 Method A (viscosity) For sealants with a viscosity lower than 75 Pa.s, the viscosity is measured with a BROOKFIE

26、LD viscometer or equivalent at the end of the specified application time according to ISO 2555. 4.2 Method B (extrusion) For sealants with a viscosity higher than 75 Pa.s, the mass extruded through a nozzle under specified conditions is measured at the end of the stated application time. 5 Method A

27、(viscosity) 5.1 Conditioning The base compound and the curing system shall be stabilized at (23 2) C in closed containers for at least 8 h before testing. 5.2 Procedure The base compound shall be mixed with the proper amount of the curing system and filled into a can. The can shall be kept at (23 2)

28、 C and tightly covered until the testing of the viscosity. At the end of the specified application time, measured from the beginning of the mixing period, the viscosity of the sealant shall be determined according to ISO 2555 using spindle, rotation speed and stirring procedures as defined in the ma

29、terial specification. BS EN 3094:2017EN 3094:2017 (E) 5 5.3 Calculation and expression of results The reading taken on the viscometer shall be converted into a viscosity value using the procedure stated for the viscometer, spindle and speed. 6 Method B (extrusion) 6.1 Apparatus 6.1.1 Sealant applica

30、tion gun 6.1.2 Sealant cartridge See Figure 1. Dimensions in millimetres Key 1 Piston 2 Cartridge 3 Nozzle 4 Diameter 40 0,1 Figure 1 Sealant cartridge 6.1.3 Nozzle See Figure 2. Dimensions in millimetres Key 1 Nozzle Figure 2 Nozzle BS EN 3094:2017EN 3094:2017 (E) 6 6.1.4 Air supply with a pressure

31、 of (620 35) kPa 6.1.5 Balance with an accuracy of 0,1 g. 6.2 Conditioning The base compound and the curing system shall be stabilized at (23 2) C in closed containers for at least 8 h before testing. 6.3 Procedure At least 250 g of the base compound shall be mixed with the proper amount of the curi

32、ng system. The mixed sealant shall promptly be filled into a cartridge (see 7.1.2) with a nozzle (see 7.1.3) and placed in a gun. The gun and sealant shall be maintained at (23 2) C throughout the test. The gun shall be attached to a constant air supply of (620 35) kPa. Initially 50 mm to 80 mm of s

33、ealant shall be extruded to clear trapped air. At the end of the specified application time, measured from the beginning of the mixing period, the sealant shall be extruded into a suitable receptacle for (60 2) s and the amount of extruded sealant determined by weighing. 6.4 Calculation and expressi

34、on of results The amount of extruded sealant shall be expressed in g.min1. 7 Designation EXAMPLE EN3094A Number of this standard Type of method (A or B) 8 Test report The test report shall include the following information: identification of the sample, batch number, number of this standard and test

35、 method (A or B), viscometer, spindle, rotating speed used, time for rotating (if more than 1 min) and stirring procedures, when testing according to method A, temperature and humidity, number of test specimens, test results, whether or not the results are within the limits of the material specifica

36、tion, date of testing. BS EN 3094:2017This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and

37、other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied

38、in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organiza

39、tion needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through

40、 our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Stan

41、dards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not tra

42、nsfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft

43、 copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A s

44、ingle paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This include

45、s scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BS

46、I Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and inte

47、rnational standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscr

48、ibing Member.PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Net

49、work Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually imp