EN 1034-26-2012 en Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 26 Roll packaging machines《机械安全-安全要求造纸完成机.pdf

《EN 1034-26-2012 en Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 26 Roll packaging machines《机械安全-安全要求造纸完成机.pdf》由会员分享，可在线阅读，更多相关《EN 1034-26-2012 en Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 26 Roll packaging machines《机械安全-安全要求造纸完成机.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 1034-26:2012Safety of machinery Safety requirements for the design and construction of paper making and finishing machinesPart 26: Roll packaging machinesBS EN 1034-26:2012

2、 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 1034-26:2012. The UK participation in its preparation was entrusted to TechnicalCommittee MCE/3/9, Paper and printing machines - Safety.A list of organizations represented on this committee can be obtained on requ

3、est to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 70178 8 ICS 85.100 Compliance with a British St

4、andard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 1034-26:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE N

5、ORM EN 1034-26 April 2012 ICS 85.100 English Version Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 26: Roll packaging machines Scurit des machines - Prescriptions de scurit pour la conception et la construction de machines de

6、fabrication et de finition du papier - Partie 26: Machines emballer les bobines Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrstung - Teil 26: Rollenpackmaschinen This European Standard was approved by CEN on 19 Feb

7、ruary 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be o

8、btained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the

9、 CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembou

10、rg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All

11、 rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1034-26:2012: EBS EN 1034-26:2012EN 1034-26:2012 (E) 2 Contents Page Foreword 41 Scope 62 Normative references 63 Terms and definitions . 74 List of significant hazards 95 Safety requirement

12、s and/or measures 105.1 General 105.2 Workplaces, access stairs, catwalks, passageways 105.3 Emergency stop device . 105.4 Control systems and actuators 115.5 Isolation and energy dissipation, prevention of unexpected start-up . 115.6 Make-ready and maintenance . 115.7 Noise . 125.8 Integrated light

13、ing 125.9 Electrical equipment 125.10 Hydraulic equipment . 125.11 Pneumatic equipment . 125.12 Ergonomic principles 125.13 Power transmission elements 125.14 Hot surfaces . 125.15 Fire 125.16 Packaging unit, folding device, head disc press, traversing packaging material unwind, integrated conveyors

14、, roll pushers, rolling deck, roll stoppers and robots 135.17 Centring station . 145.18 Packaging material unwinds 145.19 Threading the packaging material . 145.20 Device for cross cutting the packaging material 145.21 Edge trimming of packaging material . 155.22 Automatic roll labelling . 156 Verif

15、ication of safety requirements and/or measures 157 Information for use 167.1 General information . 167.2 Instruction handbook 167.3 Marking . 17Annex A (informative) Figures . 18Annex B (informative) Muting of electrosensitive protective devices on paper making and paper finishing machines 22BS EN 1

16、034-26:2012EN 1034-26:2012 (E) 3 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC 24FiguresFigure A.1 Example of a roll packaging machine with robots . 18Figure A.2 Example of a roll packaging machine with robots. 19Figure A

17、.3 Principle of a roll packaging machine with a traversing unwind for spiral winding of the packaging material web 20Figure A.4 Example of a roll packaging machine with four wrapping paper unwinds . 21Figure B.1 Equipment (paper roll turner) provided with electrosensitive protective devices (ESPDs)

18、which are muted for letting pass a paper roll . 23Figure B.2 Muting principle of an ESPD with a laser scanner. 23Tables Table 1 List of significant hazards (1 of 2) 9Table 1 (2 of 2) . 10Table 2 List of safety functions, Performance Level and Safety Integrity Level specified in this standard. 11Tabl

19、e 3 Methods used to verify safety requirements and/or protective measures . 16BS EN 1034-26:2012EN 1034-26:2012 (E) 4 Foreword This document (EN 1034-26:2012) has been prepared by Technical Committee CEN/TC 198 “Printing and Paper Machinery - Safety”, the secretariat of which is held by DIN. This Eu

20、ropean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2012, and conflicting national standards shall be withdrawn at the latest by October 2012. Attention is drawn to the possibility that some of the e

21、lements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports

22、essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europ

23、ean Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turke

24、y and the United Kingdom. BS EN 1034-26:2012EN 1034-26:2012 (E) 5 Introduction This document is a type C standard as stated in EN ISO 12100:2010. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. For mach

25、ines that have been designed and built according to the provisions of this C standard, the following stipulation applies: Where provisions of this type C standard are different from those which are stated in type A or B standards or from provisions made in EN 1034-1:2000+A1:2010, the provisions of t

26、his type C standard take precedence over the provisions of the other standards. BS EN 1034-26:2012EN 1034-26:2012 (E) 6 1 Scope This European Standard applies to roll packaging machines for use in papermaking and applies together with EN 1034-1:2000+A1:2010. It deals with all significant hazards, ha

27、zardous situations and hazardous events relevant to roll packaging machines, when used as intended and under the conditions foreseen by the manufacturer (see Clause 4). This document is not applicable to roll packaging machines which are manufactured before the date of publication as an EN. 2 Normat

28、ive references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) a

29、pplies. EN 349:1993+A1:2008, Safety of machinery Minimum gaps to avoid crushing of parts of the human body EN 614-1:2006+A1:2009, Safety of machinery Ergonomic design principles Part 1: Terminology and general principles EN 614-2:2000+A1:2008, Safety of machinery Ergonomic design principles Part 2:

30、Interactions between the design of machinery and work tasks EN 619:2002+A1:2010, Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of unit loads EN 894-1:1997+A1:2008, Safety of machinery Ergonomic requirements for the design of displays an

31、d control actuators Part 1: General principles for human interactions with displays and control actuators EN 894-2:1997+A1:2008, Safety of machinery Ergonomic requirements for the design of displays and control actuators Part 2: Displays EN 953:1997+A1:2009, Safety of machinery Guards General requir

32、ements for the design and construction of fixed and movable guards EN 1034-1:2000+A1:2010, Safety of machinery Safety requirements for the design and construction of paper making and finishing machines Part 1: Common requirements EN 1037:1995+A1:2008, Safety of machinery Prevention of unexpected sta

33、rt-up EN 1088:1995+A2:2008, Safety of machinery Interlocking devices associated with guards Principles for design and selection EN 1760-1:1997+A1:2009, Safety of machinery Pressure sensitive protective devices Part 1: General principles for the design and testing of pressure sensitive mats and press

34、ure sensitive floors EN 1760-2:2001+A1:2009, Safety of machinery Pressure sensitive protective devices Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars EN 1837:1999+A1:2009, Safety of machinery Integral lighting of machines EN 13023:2003+A

35、1:2010, Noise measurement methods for printing, paper converting, paper making machines and auxiliary equipment Accuracy grades 2 and 3 EN 13478:2001+A1:2008, Safety of machinery Fire prevention and protection EN 60204-1:2006, Safety of machinery Electrical equipment of machines Part 1: General requ

36、irements BS EN 1034-26:2012EN 1034-26:2012 (E) 7 EN 61000-6-2:2005, Electromagnetic compatibility (EMC) Part 6-2: Generic standards Immunity for industrial environments EN 61496-1:2004, Safety of machinery Electro-sensitive protective equipment Part 1: General requirements and tests EN 62061:2005, S

37、afety of machinery Functional safety of safety-related electrical, electronic and programmable electronic control systems EN ISO 4413:2010, Hydraulic fluid power General rules and safety requirements for systems and their components (ISO 4413:2010) EN ISO 4414:2010, Pneumatic fluid power General rul

38、es and safety requirements for systems and their components (ISO 4414:2010) EN ISO 10218-1:2011, Robots for industrial environments Safety requirements Part 1: Robot (ISO 10218-1:2011) EN ISO 10218-2, Robots for industrial environments Safety requirements Part 2: Robot system and integration (ISO 10

39、218-2) EN ISO 12100:2010, Safety of machinery General principles for design Risk assessment and risk reduction (ISO 12100:2010) EN ISO 13732-1:2008, Ergonomics of the the thermal environment Methods for the assessment of human responses to contact with surfaces Part 1: Hot surfaces (ISO 13732-1:2006

40、) EN ISO 13849-1:2008, Safety of machinery Safety-related parts of control systems Part 1: General principles for design (ISO 13849-1:2006) EN ISO 13849-2:2008, Safety of machinery Safety-related parts of control systems Part 2: Validation (ISO 13849-2:2003) EN ISO 13850:2008, Safety of machinery Em

41、ergency stop Principles for design (ISO 13850:2006) EN ISO 13855:2010, Safety of machinery Positioning of safeguards with respect to the approach speeds of parts of the human body (ISO 13855:2010) EN ISO 13857:2008, Safety of machinery Safety distances to prevent hazard zones being reached by the up

42、per and lower limbs (ISO 13857:2008) EN ISO 14122-2:2001, Safety of machinery Permanent means of access to machinery Part 2: Working platforms and walkways (ISO 14122-2:2001) EN ISO 14122-3:2001, Safety of machinery Permanent means of access to machinery Part 3: Stairs, stepladders and guard-rails (

43、ISO 14122-3:2001) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1034-1:2000+A1:2010, EN ISO 12100:2010 and the following apply: 3.1 roll packaging machine machine used for packaging paper rolls; the rolls are mounted on supporting drums and their ax

44、ial rotational movement causes them to be wrapped with a paper or plastic web and, where applicable, head discs (cardboard discs) are finally applied to the ends of the rolls by pressing and gluing, consisting of several machine sections/functional units including packaging material unwind(s), packa

45、ging unit, folding device, head disc press, rolls for pulling the packaging material, integrated conveyors, robots, roll pusher, roll stopper, drives and control system BS EN 1034-26:2012EN 1034-26:2012 (E) 8 Note 1 to entry: Figures in Annex A illustrate the principles of roll packaging machines. 3

46、.2 roll paper roll 3.3 packaging material unwind unwind for rolls of packaging paper or plastic film 3.4 packaging unit unit with supporting drums allowing rotation of the roll for packaging 3.5 folding device device usually with rotating and pivoted paddles for folding packaging paper side laps ove

47、r rolls 3.6 centring station unit for moving the rolls in the direction of the axle for centring them before the packaging process 3.7 head disc press device for pressing and affixing the head discs provided with for example, glue or hotmelt glue onto the roll ends 3.8 head disc round disc cut from

48、paper or cardboard 3.9 roll pusher device for pushing rolls so that they roll to another position 3.10 roll stopper device for catching and retaining the rolling roll so that it stops in a specified position 3.11 rolling deck area where the rolls roll by impact from a roll pusher or by gravity to a

49、roll stopper 3.12 roll-in-area area where the rolls are transported e.g. by a conveyor into the roll packaging machine 3.13 roll-out-area area where the rolls are transported e.g. by a conveyor out of the roll packaging machine 3.14 integrated conveyor conveyor for roll handling in the area of the ro