EN 12020-1-2008 en Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1 Technical conditions for inspection and delivery《铝及铝合金 .pdf

《EN 12020-1-2008 en Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1 Technical conditions for inspection and delivery《铝及铝合金 .pdf》由会员分享，可在线阅读，更多相关《EN 12020-1-2008 en Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1 Technical conditions for inspection and delivery《铝及铝合金 .pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 12020-1:2008Aluminium and aluminium alloys Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 Part 1: Technical conditions for inspection and deliveryICS 77.150.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g5

2、9g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIBS EN 12020-1:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2008 BSI

3、2008ISBN 978 0 580 55565 7National forewordThis British Standard is the UK implementation of EN 12020-1:2008. It supersedes BS EN 12020-1:2001 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations

4、 represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. Amen

5、dments/corrigenda issued since publicationDate CommentsLicensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 12020-1March 2008ICS 77.150.10 Supersedes EN 12020-1:2001 English VersionAluminium and aluminium alloys - Extruded precision profiles i

6、nalloys EN AW-6060 and EN AW-6063 - Part 1: Technicalconditions for inspection and deliveryAluminium et alliages daluminium - Profils de prcisionfils en alliages EN AW-6060 et EN AW-6063 - Partie 1:Conditions techniques de contrle et de livraisonAluminium und Aluminiumlegierungen - StranggepresstePr

7、zisionsprofile aus Legierungen EN AW-6060 und ENAW-6063 - Teil 1: Technische LieferbedingungenThis European Standard was approved by CEN on 10 February 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the s

8、tatus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German).

9、A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic,

10、 Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALIS

11、ATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12020-1:2008: ELicensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIEN 12020-1:2008

12、 (E) 2 Contents Page Foreword . 3 1 Scope 4 2 Normative references 5 3 Terms and definitions. 5 4 Ordering information 6 4.1 General . 6 4.2 Reference to a drawing. 7 5 Requirements 7 5.1 Production and manufacturing processes.7 5.2 Quality control . 8 5.3 Chemical composition limit . 8 5.4 Mechanic

13、al properties 8 5.5 Freedom from surface defects. 8 5.6 Tolerances on dimensions and form 8 5.7 Section mass . 8 6 Test procedures 8 6.1 Sampling 8 6.2 Test methods . 9 7 Inspection documents 9 8 Marking of products 9 9 Packaging 10 10 Arbitration 10 Bibliography 11 BS EN 12020-1:2008Licensed Copy:

14、:FULLNAME, : DATE, Uncontrolled Copy, (c) BSIEN 12020-1:2008 (E) 3 Foreword This document (EN 12020-1:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national

15、standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by September 2008. This document supersedes EN 12020-1:2001. Within its programme of work, Technical committee CEN/TC 132 entru

16、sted CEN/TC 132/WG 5 “Extruded and drawn products“ to revise EN 12020-1:2001 The following technical modifications have been introduced during the revision: Clause 3: Definition of “order document“ is included Subclause 4.2: An additional Figure 3 is included identifying visible surfaces and weld li

17、nes Subclause 5.5: Requirements to streaks and surface texture appearance on visible surfaces in mill finish are included Subclause 5.7: Requirements to tolerance on mass are included EN 12020 comprises the following parts under the general title “Aluminium and aluminium alloys Extruded precision pr

18、ofiles in alloys EN AW-6060 and EN AW-6063“: Part 1: Technical conditions for inspection and delivery Part 2: Tolerances on dimensions and form Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held r

19、esponsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardized standards products under reasonable and not discriminatory conditions then this product shall be removed from the corresponding sta

20、ndard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,

21、Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 12020-1:2008Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIEN 12020-1:2008 (E) 4 1 Scope This document specifies tech

22、nical conditions for inspection and delivery of alloys EN AW-6060 and EN AW-6063 extruded precision profiles manufactured with and without a thermal barrier (see Figures 1 and 2) and without further surface treatment. Precision profiles covered in this document are distinguished from extruded profil

23、es for general applications covered in EN 755-9 by the following characteristics: they are mainly for architectural applications; they meet more stringent requirements regarding the surface condition of visible surfaces; the maximum diameter of the circumscribing circle CD is 350 mm; they are made t

24、o closer tolerances on dimensions and form. In the case of profiles, which, due to the complexity of their design are difficult to manufacture and specify, then special agreements between supplier and purchaser may need to be reached. NOTE The effect of the thermal barrier material on the dimensiona

25、l tolerances is covered by EN 12020-2 although the actual thermal barrier material itself is not (see EN 14024). Key 1 CD maximum 350 mm Key 1 CD maximum 350 mm 2 thermal barriers Figure 1 Profile without thermal barrier Figure 2 Profile containing thermal barrier BS EN 12020-1:2008Licensed Copy: :F

26、ULLNAME, : DATE, Uncontrolled Copy, (c) BSIEN 12020-1:2008 (E) 5 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references only the edition cited applies. For undated references the latest edition of the referenced document

27、 (including any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought products Temper designations EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products EN 755-1, Aluminium and aluminium alloys E

28、xtruded rod/bar, tube and profiles Part 1: Technical conditions for inspection and delivery EN 755-2, Aluminium and aluminium alloys Extruded rod/bar, tube and profiles Part 2: Mechanical properties EN 10002-1, Metallic materials Tensile testing Part 1: Method of test at ambient temperature EN 10204

29、, Metallic products Types of inspection documents EN 12020-2, Aluminium and aluminium alloys Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 Part 2: Tolerances on dimensions and form EN 12206-1, Paints and varnishes Coating of aluminium and aluminium alloys for architectural purposes

30、 Part 1: Coatings prepared from coating powder EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Part 1: General terms EN 12373-1, Aluminium and aluminium alloys Anodizing Part 1: Method for specifying decorative and protective anodic oxidation coatings on aluminium EN 14242, Alu

31、minium and aluminium alloys Chemical analysis Inductively coupled plasma optical emission spectral analysis EN 14361, Aluminium and Aluminium alloys Chemical analysis Sampling from metal melts EN ISO 4287, Geometrical product specifications (GPS) Surface texture: Profile method Terms, definitions an

32、d surface texture parameters (ISO 4287:1997) EN ISO 4288, Geometrical product specifications (GPS) Surface texture: Profile method Rules and procedures for the assessment of surface texture (ISO 4288:1996) EN ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method (ISO 6506-1:2005)

33、3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 order document document or set of documents agreed between supplier and purchaser at the time of ordering BS EN 12020-1:2008Licensed Copy: :FULLNAME, : DATE, Unc

34、ontrolled Copy, (c) BSIEN 12020-1:2008 (E) 6 4 Ordering information 4.1 General The order document shall contain the following: a) the designation of the aluminium alloy (EN AW-6060 or EN AW-6063); b) the temper of the material for delivery in accordance with EN 755-2 (The temper designations to be

35、used are according to EN 515); c) the application, in particular, when surface treatment is intended; this shall be expressly stated on the order document; d) reference to this document (EN 12020-1); e) reference to a drawing defining the product (see 4.2), cross sectional dimensions, mass per meter

36、 calculated on nominal section dimensions, surface requirements and any other relevant information; f) length: fixed or random, for random lengths minimum and maximum shall be specified, an allowance for process contact points of surface treatment may be necessary; g) quantity: mass or number of pie

37、ces or total length, tolerance on quantity; h) special requirements: any special requirements agreed between the supplier and purchaser, agreement on plane parallelism, any requirement for inspection documents, marking of products, reference to other standards, if tolerances on dimensions and form d

38、iffer from those specified in EN 12020-2, additional or special testing, installation length, surface protection; i) packaging information: pack mass/size. BS EN 12020-1:2008Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIEN 12020-1:2008 (E) 7 4.2 Reference to a drawing On the basis of t

39、he order document, the manufacturer shall prepare drawings, which are to be checked by the purchaser for accuracy, and approved, the profiles then being manufactured in strict accordance with the approved drawing. If for dimensions critical to function, tolerances other than those specified in this

40、document are to be used, they shall be entered in the drawing adjacent to the associated nominal size. This also applies to the tolerances on form. Where profiles are intended for later assembly, it is recommended that the manufacturer is provided with a drawing giving appropriate details. Where for

41、 manufacturing reasons weld lines are to be located on visible surfaces their position or approximate area of appearance should be indicated by the manufacturer on the drawing. Visible surfaces shall be identified, indicating main and, if necessary, secondary order visible surfaces. Key 1 visible su

42、rface 2 area of probable appearance of weld lines 3 area of probable appearance of T-joint streaks Figure 3 Marking of visible surfaces of approximate area of appearance of weld lines and T-joint streaks For profiles intended for surface treatment, surfaces and areas that are to be so treated should

43、 be indicated on the drawing. If the outline of a profile is modified by machining, it is recommended that the final shape is also indicated. 5 Requirements 5.1 Production and manufacturing processes Unless otherwise specified in the order document, the production and manufacturing processes shall b

44、e left to the discretion of the manufacturer. Unless it is explicitly stated in the order document, no obligation shall be placed on the manufacturer to use the same processes for subsequent or similar orders. BS EN 12020-1:2008Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIEN 12020-1:2

45、008 (E) 8 5.2 Quality control The supplier shall be responsible for the performance of all inspection and tests required by the relevant European Standard and/or the particular specification prior to shipment of the product. If the purchaser wishes to inspect the product at the manufacturers works,

46、he shall notify the supplier at the time of placing the order. 5.3 Chemical composition limit The chemical composition limit shall be in conformity with the requirements specified in EN 573-3. If the purchaser requires closer limits for elements than those specified in the above standard, these limi

47、ts shall be according to an agreement between supplier and purchaser and stated in the order document. 5.4 Mechanical properties The mechanical properties shall comply with the requirements of EN 755-2 or those agreed between supplier and purchaser and stated in the order document. Hardness testing

48、may be used for release purposes subject to agreement between supplier and purchaser. 5.5 Freedom from surface defects The extruded visible surface shall be free from defects prejudicial to its suitable and proper use. Slight scoring and other minor defects are permissible providing that values of R

49、z of 9 m or Ra of 2 m are not exceeded when determined according to EN ISO 4287 and EN ISO 4288. Any discoloration or minor blemishes that are likely to be eliminated by the intended pretreatment for anodizing according to EN 12373-1 or by painting according to EN 12206-1 shall be permitted. Requirements on streaks and surface texture appearance on visible surfaces in mill finish, anodized and painted conditions shall be agreed between supplier and purchaser.