DLA MS28774 REV M-2009 RETAINER PACKING BACKUP SINGLE TURN POLYTETRAFLUOROETHYLENE.pdf

《DLA MS28774 REV M-2009 RETAINER PACKING BACKUP SINGLE TURN POLYTETRAFLUOROETHYLENE.pdf》由会员分享，可在线阅读，更多相关《DLA MS28774 REV M-2009 RETAINER PACKING BACKUP SINGLE TURN POLYTETRAFLUOROETHYLENE.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5330 MS28774M 23 APRIL 2009 SUPERSEDING MS28774L 19 NOVEMBER 1990 DETAIL SPECIFICATION SHEET RETAINER, PACKING BACKUP, SINGLE TURN, POLYTETRAFLUOROETHYLENE This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acq

2、uiring the product described herein shall consist of this specification sheet and procurement specification SAE AS8791. TM(SEE NOTE 4)WENDS TO BEPARALLEL TOCENTER LINE 5G GAP(SEE NOTE 5)THE DIRECTION OF THE SCARFCUT FROM THE LOWER LEFT TOTHE UPPER RIGHT OR FROM UPPERLEFT TO LOWER RIGHT IS OPTIONAL.A

3、FIGURE I. Retainer. INCH-POUNDInactive for new design after 25 MARCH 1989.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28774M 2TABLE I. Part Numbers and Dimensions. PART NUMBER M .001 T W G A MS28774-004 .109 .052 .054 .005 39 +0 -4 MS28774-005

4、.124 .045 .052 .000 33 +0 -3 MS28774-006 .140 30 +0 -3MS28774-007 .171 26 +0 -3 MS28774-008 .202 22 +0 -3MS28774-009 .234 MS28774-010 .265MS28774-011 .327 MS28774-012 .390MS28774-013 .455 MS28774-014 .518MS28774-015 .580 MS28774-016 .643MS28774-017 .705 MS28774-018 .768MS28774-019 .830 MS28774-020 .

5、898MS28774-021 .960 MS28774-022 1.023MS28774-023 1.085 MS28774-024 1.148MS28774-025 1.210 MS28774-026 1.273MS28774-027 1.335 MS28774-028 1.398MS28774-110 .390 .087 .006 MS28774-111 .452 .085 .000 MS28774-112 .515 MS28774-113 .577 MS28774-114 .640 MS28774-115 .702 MS28774-116 .765 MS28774-117 .832 MS

6、28774-118 .895 MS28774-119 .957 MS28774-120 1.020 MS28774-121 1.082 MS28774-122 1.145 MS28774-123 1.207 MS28774-124 1.270 MS28774-125 1.332 MS28774-126 1.397 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28774M 3TABLE I. Part Numbers and Dimensio

7、ns. - continued PART NUMBER M .001 T W G A MS28774-127 1.459 .052 .087 .006 22 +0 -3 MS28774-128 1.522 .045 .085 .000 MS28774-129 1.584 MS28774-130 1.647 MS28774-131 1.709 MS28774-132 1.772 MS28774-133 1.834 MS28774-134 1.897 MS28774-135 1.959 MS28774-136 2.022 MS28774-137 2.084 MS28774-138 2.147 MS

8、28774-139 2.209 MS28774-140 2.258 MS28774-141 2.320 MS28774-142 2.383 MS28774-143 2.445 MS28774-144 2.508 MS28774-145 2.570 MS28774-146 2.633 MS28774-147 2.695 MS28774-148 2.758 MS28774-149 2.820 MS28774-210 .766 .120 MS28774-211 .828 .118MS28774-212 .891 MS28774-213 .953 MS28774-214 1.016 MS28774-2

9、15 1.078 MS28774-216 1.141 MS28774-217 1.203 MS28774-218 1.266 MS28774-219 1.334 MS28774-220 1.397 MS28774-221 1.459 MS28774-222 1.522 MS28774-223 1.647 .007 MS28774-224 1.772 .000MS28774-225 1.897 MS28774-226 2.022 MS28774-227 2.147 MS28774-228 2.272 MS28774-229 2.397 MS28774-230 2.522 Provided by

10、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28774M 4TABLE I. Part Numbers and Dimensions. - continued PART NUMBER M .001 T W G A MS28774-231 2.631 .052 .120 .007 22 +0 -3 MS28774-232 2.756 .045 .118 .000 MS28774-233 2.881 MS28774-234 3.006 MS28774-235 3.13

11、1 MS28774-236 3.256 MS28774-237 3.381 MS28774-238 3.506 MS28774-239 3.631 MS28774-240 3.756 MS28774-241 3.881 MS28774-242 4.006 MS28774-243 4.131 MS28774-244 4.256 MS28774-245 4.381 MS28774-246 4.506 MS28774-247 4.631 MS28774-325 1.513 .075 .184 MS28774-326 1.638 .065 .182 MS28774-327 1.763 MS28774-

12、328 1.888 MS28774-329 2.013 MS28774-330 2.138 MS28774-331 2.268 MS28774-332 2.393 MS28774-333 2.518 MS28774-334 2.643 MS28774-335 2.768 MS28774-336 2.893 MS28774-337 3.018 MS28774-338 3.143 MS28774-339 3.273 MS28774-340 3.398 MS28774-341 3.523 MS28774-342 3.648 MS28774-343 3.773 MS28774-344 3.898 MS

13、28774-345 4.028 MS28774-346 4.153 MS28774-347 4.278 MS28774-348 4.403 MS28774-349 4.528 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28774M 5TABLE I. Part Numbers and Dimensions. - continued PART NUMBER M .001 T W G A MS28774-425 4.551 .110 .237

14、 .008 22 +0 -3 MS28774-426 4.676 .100 .235 .000 MS28774-427 4.801 MS28774-428 4.926 MS28774-429 5.051 MS28774-430 5.176 MS28774-431 5.301 MS28774-432 5.426 MS28774-433 5.551 MS28774-434 5.676 MS28774-435 5.801 MS28774-436 5.926 MS28774-437 6.051 MS28774-438 6.274 MS28774-439 6.524 MS28774-440 6.774

15、MS28774-441 7.024 MS28774-442 7.274 MS28774-443 7.524 MS28774-444 7.774 MS28774-445 8.024 MS28774-446 8.524 MS28774-447 9.024 MS28774-448 9.524 MS28774-449 10.024 MS28774-450 10.524 .010 MS28774-451 11.024 .000MS28774-452 11.524 MS28774-453 12.024MS28774-454 12.524 MS28774-455 13.024MS28774-456 13.5

16、24 MS28774-457 14.024MS28774-458 14.524 MS28774-459 15.024MS28774-460 15.524 Notes: 1. Material shall be in accordance with procurement specification: SAE AS8791. 2. Surfaces must be smooth and free from irregularities. Edges must be clean and sharp. 3. Dimension “A” in degrees, all other in inches.

17、 4. For use in packing grooves conforming to MIL-G-5514. 5. In measuring dimensions M over a mandrel, the scarf cut shall not exceed dimension “G” and no overlap permitted beyond the full scarf. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS28774

18、M 66. For parts 140-149, 231-247, 438-460, it is recommended that the respective dash sizes under MS27595 (not cut) be used when possible. 7. For design purposes, this standard takes precedence over procurement specification referenced here-in. 8. Changes from previous issue. Marginal notations are

19、not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Army -MR DLA -IS Navy - AS Air Force 99 (Project 5330-2009-009) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-