DLA MIL-S-8642 F-1994 SURVIVAL KIT INDIVIDUAL《个人急救装置》.pdf

《DLA MIL-S-8642 F-1994 SURVIVAL KIT INDIVIDUAL《个人急救装置》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-S-8642 F-1994 SURVIVAL KIT INDIVIDUAL《个人急救装置》.pdf（61页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-8642F 24 October 1994 SUPERSEDING 20 August 1979 MIL-S-8642E MILITARY SPECIFICATION SURVIVAL KIT, INDIVIDUAL This specification is approved for use by all departments and agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for two types of surv

2、ival kits. * 1.2 Classification. The survival kits shall be of the following types, as specified (see 6.2): Type I - ax (wood handle) and saw Type II - deleted (see 6.5) Type III - deleted (see 6.5) Type IV - ax with guard and leather grip Beneficial comments (recommendations, additions, deletions)

3、and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FQSD, 2809 South 20th Street, Philadelphia, PA 19145-0599, by using Standardization Document Improvement Proposal (DD Form 142

4、6) appearing at the end of this document or by letter. AMSC N/A FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-S-Bb42F 997990b 1794882 703 W MIL-S-8642F

5、2. APPLICABLE DOCUMENTS 2.1 Government Documents 2.1.1 Specifications, standards, and handbooks. The following 1 specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in th

6、e issue of the Department of Defense Index of Specifications and Standards (DODISS) and its supplement as cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL L-P-375 V-F-106 V-L-61 V-T-295 FF-N-845 FF-R-5 5 6 FF-W-84 KK-L- 16 5 A-A- 1 O 37 TT-P- 17 5 7 TT-L-32 ccc-c-419 CCC-D-950 PPP-B-636 P

7、PP-T-45 -Plastic Film, Flexible, Vinyl Chloride -Fastener, Slide, interlocking -Laces, Footwear, Nylon -Thread, Nylon -Nut, Plain, Wing -Rivets, Solid, Small; Rivets, Split Small; Rivets, Tubular, Small; and Caps, Rivets; General Purpose -Washers, Lock (Spring) -Leather, Cattlehide, Vegetable-Tanned

8、 and Chrome Retanned, Impregnated; and Soles -Wire Fabric,(Industrial) -Primer Coating, Zinc Chromate, Low Moisture-Sensitivity -Lacquer, Cellulose Nitrate, Gloss, for Aircraft Use -Cloth, Duck, Cotton, Unbleached, Plied- Yarns, Army and Numbered -Dyeing and Aftertreating Processes for Cotton Cloths

9、 -BOX, Fiberboard for Sealing and Securing -Tape, Gummed, Paper, Reinforced and Plain, for Sealing and Securing 2 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-Bb42F W 99999Ob 1994883 birT W MIL-S-8642F . M I L I TARY MIL-B-131 MIL-P-149 MI

10、L-F-495 MIL-W-530 MIL-C-5040 MIL-1-6903 MIL-C-8514 MIL-F-10884 MIL-C-13924 0 MIL-G-16491 MIL-T-43566 STANDARDS FEDERAL FED-STD-66 FED-STD-151 FED-STD-751 -Barrier, Material, Water Vaporproof, Flexible -Plastic Coating Compound, Strippable (Hot Dipping) -Finish, Chemical Black, for Copper Alloys -Web

11、bing and Tape, Textile, Cotton, General Purpose, Natural or in Colors -Corci, Nylon -Ink, Marking (For Parachutes And Other Textile Items) -Coating Compound, Metal Pretreatment, Resin-Acid -Fasteners, Snap -Coating, Oxide, Black, for Ferrous Metals -Grommet, Metallic -Tape, Textile, Cotton, General

12、Purpose, Natural or in Colors -Steel; Chemical Conipogition and Harden- ability -MetPls; Test Methods -Stitches, Seams, Stitchings 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-130 MS27980 MS27982 MIL-S-b4

13、2F 999990b L9944 5b MIL-S-8642F -Sampling Procedures and Table for Inspection by Attributes -Marking for Shipment and Storage -Identification Marking of U.S. Military Property -Fasteners, Snap, Style 2 (Regular Wire Spring Clamp Type) -Fasteners, Snap, Style 3 (Pronged Ring Head Type) (Unless otherw

14、ise indicated, copies of Federal and military specifications, standards and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government Publications. The following document forms a part of this document to the

15、extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the

16、 solicitation (see 6.2). COLOR ASSOCIATION OF THE UNITED STATES, INCORPORATED TCA Cable Numbers and Colors (TCA cable numbers and colors are published by the Color Association of the United States, Incorporated, 200 Madison Avenue, New York, NY 10016-0927.) 4 1 Provided by IHSNot for ResaleNo reprod

17、uction or networking permitted without license from IHS-,-,-MIL-S-BbqZF 9999906 1994885 412 MIL-S-8642F 3. REQUIREMENTS 3.1 First article. Unless otherwise specified, the survival tool kits furnished under this specification shall be products which have been inspected and have passed the first artic

18、le inspection specified in 4.3 through 4.3.2. e 3.2 Materials and components. The materials and components shall conform to the applicable specifications and standards as listed or required herein. 3.2.1 Blades 3.2.1.1 Saw kit, 1.25 IV 2.0 3.7 Performance inspections 3.7.1 Deformity of the blades la

19、x, wood saw, and hacksaw) and the scraper. Any concave or convex deviation of the ax, wood saw, and hacksaw blades and the scraper, as applicable, shall not exceed 1/16 inch, when inspected as specified in 4.5.3. 3.7.2 Saw cuttinq. * 3.7.2.1 Wood saw blade. When inspected as specified in 4.5.8.1, th

20、e wood saw blade shall be capable of making a minimum of four - one inch deep cuts without the breaking of the blade or teeth or any damage to the teeth or saw and scraper grip. The time required to make each one inch deep cut shall not exceed 5 minutes. 3.7.2.2 Hacksaw blade. When inspected as spec

21、ified in 4.5.8.2, the hacksaw blade shall be capable of cutting the steel tube into eight sections without the breaking of the blade or teeth or any damage to the teeth or the saw and scraper grip. No rivet shall become loose or break. 3.7.3 Stress of the scraper. When inspected as specified in 4.5.

22、9, the scraper shall not break, deform, or crack. 3.7.4 Sharpeninq of the ax blade. When inspected as specified in 4.5.10, the sharpening stone shall be capable of sharpening and honing the ax blade and sickle hook cutting edges without disintegrating or damaging the ax blade. * 3.7.5 Ax cuttinq. Wh

23、en tested as specified in 4.5.7, the ax shall be capable of cutting through vines, shrubbery, tree sprouts, saplings, etc. without damage to the ax. 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-8642F 3.8 Color 3.8.1 Ax and saw carrvina ca

24、ses. The color of the cotton cloth for the ax and saw carryinq cases shall be Olive Drab and - approximately match TCA Cable No. 66022, Shade S-1 (U.S. Army Olive Drab). 3.8.2 Tape, webbinq, cord, and les strap. The color of the tape, webbing, cord, and leg strap shall approximately match the color

25、of the cotton cloth used for the ax and saw carrying cases (see 3.8.1). 3.8.3 Sharpeninq stone carryinq. The color of the sharpening stone carrying case shall be bright red. 3.8.4 Ax handle and saw and scraper grip. The ax handle and the saw and scraper grip of the type I kit shall be finished in a

26、bright red color. The finish shall not crack, chip, or scale in normal usage. 3.9 Finish 3.9.1 Ax auard. The type IV ax guard shall be uniformly coated, first with the metal pretreatment coating compound conforming to MIL-C-8514, then with the zinc chromate primer conforming to TT-P-1757, color Y or

27、 T, and finally with the cellulose nitrate lacquer conforming to TT-L-32, color gloss black. Prior to the insertion of the leather washers, the upset portion of the side edges of the ax blade tang at the bottom slot of the guard shall be coated with the black cellulose nitrate lacquer. After the top

28、 of the tang has been upset on the top of the guard surface, the upset surface shall be uniformly coated, first with the metal pretreatment coating compound, then with zinc chromate primer, and finally with the black cellulose nitrate lacquer. 3.9.2 Ax, wood saw, and hacksaw blades and the scraper.

29、The entire surfaces of the ax, wood saw, and hacksaw blades and the scraper, as applicable, shall be uniformly coated with the black oxide coating compound conforming to MIL-C-13924, class 1 (see 4.5.4). After all the specified edges of the ax and saw blades and the scraper, as applicable, have been

30、 sharpened, the corrosion preventative compound Rust Proof X-700 as manufactured by E.G. Walters, Inc., Orwigsburg, Pennsylvania, or equivalent, shall be uniformly applied to all the exposed metal surfaces. After the application of the corrosion preventative compound, the forward portion of the wood

31、 saw blade shall be encased in a snug fitting bag fabricated from the vinyl plastic film. The bag shall be of sufficient length to fully cover the entire sharpened back edge and shall be of a reasonably snug fit. 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

32、 from IHS-,-,-MIL-S-8642F 3.10 Markinqs. All the identification markings shall be in accordance with MIL-STD-130 and shall be not less than 1/4 inch high. All markings shall be thoroughly dry prior to packing or packaging. * 3.10.1 Ax and saw carryinq cases. The underside of each ax and saw carrying

33、 case, as applicable, shall be marked with the marking ink, as follows: SURVIVAL KITS; INDIVIDUAL, TOOL NAME OF MANUFACTURER TYPE (AS APPLICABLE) CONTRACT NO. NSN MIL-S-8642F The carrying case for the type IV kit shall also contain the 1/2 inch high markings specified in Figure 17. * 3.10.2 Tools. E

34、ach tool shall be marked, in accordance with MIL-STD-130, as follows: NAME OF MANUFACTURER OR TRADE MARK NAME OF TOOL MIL-S-8642F * 3.11 Workmanship. After completion of the final assembly, the survival tool kits shall be thoroughly cleaned and all loose thread, lint, and foreign matter shall be rem

35、oved. Each grommet and snap fastener shall be clinched without distortion, damage, splitting, or cutting of the cloth, webbing, or tape, as applicable. The tool kits shall not contain any crack, nick, burr, unspecified sharp edge or hole, tear, needle chew, mend, patch, spot, stain corrosion or scal

36、e, pit, or dent. Because of the emergency use of these items, the importance of providing a product of uniform excellent quality cannot be overemphasized. The tool kits shall be uniform in quality and shall be free from irregularities or defects which could adversely affect performance, reliability,

37、 or durability. The survival tool kits shall conform to quality and grade of product established by this specification. The occurrence of defects shall not exceed the acceptance criteria established herein. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified

38、 in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requirem

39、ents specified herein, unless disapproved by the Government. 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-8642F The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are

40、deemed necePsary to assure supplies and services conform to prescribed requirements. 4.2 Classification of inspection. The examination and testing of the kits shall be classified as follows: a. First article inspection. First article inspection consists of examinations and tests performed on samples

41、 which are representative of the production item after award of a contract to determine that the production item conforms to the requirements of this specification (see 4.3 through 4.3.2). b. Quality conformance inspection. Quality conformance inspection consists of examinations and tests performed

42、on individual products or lots to determine conformance of the products or lots with the requirements set forth in this specification (see 4.4 through 4.4.1.2). 4.3 First article inspection. The first article inspection of the kits shall consist of examination and tests for all the requirements of t

43、his specification. 4.3.1 First article samples. Unless otherwise specified, as soon as practicable after the award of the contract or order, the manufacturer shall submit five kits of each type specified in the contract or order. The samples shall be representative of construction, workmanship, comp

44、onents, and materials to be used during production. When a contractor is in continuous production of these kits from contract to contract, submission of further first article inspection samples on the new contract may be waived at the discretion of procuring activity (see 6.2). waiving of the first

45、article inspection does not preclude the requirements for performing the quality conformance inspection. The first article inspection samples shall be furnished to-the Government as directed by the Contracting Officer (see 6.2.). 4.3.2 Upon completion of the first article inspection, all the applica

46、ble inspection reports and when applicable, recommendations and comments pertinent for use in monitoring production wiIl be forwarded to the cognizant Government activity. One of the approved first article inspection sample kits of each type, as applicable, will be returned to the manufacturer for u

47、se in monitoring production. The other four kits of each type, as applicable, wil be destroyed in the first article inspection an shall not be considered as part of the quantity to be delivered under the contract. Approval of the first article inspection samples or the I 18 1 Provided by IHSNot for

48、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-BbYZF = 9999906 L948 TO7 m MIL-S-8642F 4.4 Quality conformance inspection. The sampling and inspection levels shall conform to MIL-STD-105. The quality conformance inspection shall consist of the following: Visual exami

49、nation of the kits Dimensional check of the kits Weight of the kits Deformity of the ax, wood saw, and hacksaw blades and the Finish of the ax, wood saw, and hacksaw blades and scraper, Thickness of the ax, wood saw, and hacksaw blades, hacksaw Rockwell hardness of the ax, wood saw, and hacksaw blades Cutting the ax, wood saw, and hacksaw blades, as applicable Stress of the scraper Sharpening of the ax blade Packaging