DLA MIL-S-3788 G-1991 SHAPER WOODWORKING《木工艺模型》.pdf

《DLA MIL-S-3788 G-1991 SHAPER WOODWORKING《木工艺模型》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-S-3788 G-1991 SHAPER WOODWORKING《木工艺模型》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、)c i MIL-S-37G 32 M 9999906 O469076 LI W I INCH- POUND I MIL-S-3788G 8 Februarv 1991 SUPERSEDING 23 January 1986 MIL-S-3788F MILITARY SPECIFICATION SHAPER, WOODWORKING This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specif

2、ication covers single and double spindle woodworking shapers of the floor-mounted type with equipment and accessories specified herein. Requirements set forth in this specification and the completed ordering data (see paragraph 6.2) establish the Governments minimum requirements for each procurement

3、. 1.2 Classification. The shapers shall be of the following types and sizes. The types and sizes to be furnished shall be as specified (see 3.5 and 6.2). Type I - Single Spindle Size 1 - 1 hp - 20-inch by 26-inch table Size 2 - 2 hp - 24-inch by 36-inch table Size 3 - 5 hp - 35-inch by 42-inch table

4、 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Industrial Plant Equipment Center, ATTN: DIPEC-SSM, 2163 Airways Boulevard, Memphis, Tennessee 38114-5051, by using the Standardization D

5、ocument Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 3220 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-S

6、-3788G 32 9999906 0469077 6 = MIL-S-3788G Type II - Double Spindle Size 1 - 2 hp (each spindle) - 12-inch, center-to-center, between Size 2 - 2 hp (each spindle) - 18-inch, center-to-center, between Size 3 - 3 hp (each spindle) - 24-inch, center-to-center, between Size 4 - 3 hp (each spindle) - 30-i

7、nch, center-to-center, between spindles, 26-inch by 36-inch table spindles, 30-inch by 48-inch table spindles, 30-inch by 60-inch table spindles, 30-inch by 66-inch table 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 SDecifications, standards, and handbooks. The following speci- cations, a

8、nd handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). s

9、tandards, SPECIFICATIONS MI L ITARY MIL-M-18058 - Machinery, Metal and Woodworking, Packaging of. STANDARDS FEDERAL FED-STD-H28 - Screw-Thread Standards for Federal Services. MI L ITARY MIL-STD-461 - Electromagnetic Emission and Susceptibility Requirements for the Control of Electromagnetic Interfer

10、ence. MIL-STD-462 - Electromagnetic Interference Characteristics, Measurement of. (Unless otherwise indicated, copies of Federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-

11、 5094.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-S-3788G 32 m 9999906 04b9078 8 m MIL-S-3788G 2.1.2 Other Government documents, drawinqs, and Dub1 ications. The follow- ing other Government documents, drawings, and publications form a

12、part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. CODE OF FEDERAL REGULATIONS (CFR) U. S. DEPARTMENT OF LABOR, OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) 29 CFR 1910 - Occupational Safety and Health Standards.

13、(Application for copies should be addressed to the Superintendent of Documents, U. S. Government Printing Office, Washington, DC 20402-0001.) (Copies of specifications, standards, handbooks, drawings, publications, and other Government documents required by contractors in connection with specific ac

14、quisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Non-Government Dublications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DO

15、D adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI O1 .la - Safety Require

16、ments for Woodworking Machinery. (DOD adopted) (Application for copies should be addressed to the American National Standards Insti tute, ATTN: Sal es Department, 1430 Broadway, New York, NY 10018-3363.) NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA) NEMA ICs 1 - Industrial Controls and System

17、s. (DOD adopted) NEMA ICs 6 - Enclosures for Industri al Control s and Systems. (DOD adopted) NEMA MG 1 - Motors and Generators. (DOD adopted) (Application for copies should be addressed to the Nation.al Electrical Manufacturers Association, 2101 L Street, N.W., Washington, DC 20037-1580.) 3 Provide

18、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-S-3788G 32 m 9999906 0469079 T m MIL-S-3788G (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also m

19、ay be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws a

20、nd regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), one complete shaper shall be subjected to first article inspection (see 6.4) in accordance with 4.4. 3.2 Design. The shaper shall be new (not a prototype) and one of the manufac

21、turers current production models capable of operations in accordance with the requirements herein. The shaper shall include all components, parts, and features necessary to meet the performance requirements specified herein. All parts subject to wear, breakage, or distortion shall be readily accessi

22、ble for adjustment, replacement, or repair. 3.2.1 Measurinq and indicatinq device calibrations. Measuring and indicating devices shall be graduated in inch-pound (see 6.5.1), metric (see 6.5.2), or dual (inch-pound and metric) units as specified by the procuring activity (see 6.2). Regardless of the

23、 measurement system used, all measuring and indicating devices on the shapers shall be graduated in the same system. 3.2.1.1 Dials. All dials used to indicate machine axes position or tool movement shall be graduated in increments not larger than 0.001 inch. Dial and handwheel circumferences shall b

24、e permanently and legibly engraved or etched on a nonglare background with graduations that can be read from the operators normal position. All feed dials shall have independent zero adjustments and shall be calibrated in such a manner that the last dial graduation progresses into and is continuous

25、with the first dial graduation as the dial is rotated through the zero position. 3.2.2 Reclaimed materials. The machine may contain reclaimed materials to the maximum extent possible provided such materials will not jeopardize the intended use, performance, or design life of the machine. Reclaimed m

26、aterials shall have been collected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw materials. None of the above shall be interpreted to mean that the use of used, rebuilt, or remanufactured end products are allowed under this specification.

27、 3.2.3 Enerqy efficiency. The shapers and their components that directly consume energy in normal operation shall be designed and constructed for 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-T MIL-S-3788G 32 m 9999906 0469080 b m MIL-S-3788G ene

28、rgy efficiency in accordance with the latest developments available within the industry. 3.2.4 Control s. Al 1 mechani cal , hydraul i c , and pneumat i c operat i ng controls shall be located convenient to the operators work station(s). 3.2.5 Safetv and health reauirements. All parts, components, m

29、echanisms, and assemblies furnished on the shapers, whether or not specifically required herein, shall conform to all requirements of OSHA 29 CFR 1910 and ANSI 01.1. If a conflict arises between 29 CFR 1910 and ANSI 01.1, 29 CFR 1910 shall apply. Additional safety and health requirements shall be as

30、 specified (see 6.2). Covers, guards, or other safety devices normally furnished as standard on the manufacturers commercial shapers suppl ied to the commercial market shall be provided for the point of operation and all other parts of the shapers that present safety hazards. If point-of-operation g

31、uarding is influenced by workpiece size and configuration, the procuring activity shall provide part design data to the supplier of the machine (see 6.2). The supplier of the machine shall provide the special guarding which shall meet OSHA 29 CFR 1910. 3.2.6 Mercurv restriction. The shapers shall no

32、t contain mercury or mercury compounds nor be exposed to free mercury during manufacture. 3.2.7 Asbestos restriction. Asbestos and materials containing asbestos shall not be used on or in the shapers. 3.2.8 Environmental Drotecti on. During the manufacture, operati on , service, transportation, or s

33、torage of the machine and its components, materi al s hazardous to the ecological system as prohibited by appl icabl e Federal, state, or local statutes in effect on the date of the contract shall not be used or emitted. O 3.2.9 Lubrication. Means shall be provided to ensure adequate lubrication for

34、 all moving parts. Recirculating lubrication systems shall include a cleanable or replaceable filter. Means for determining oil level in each reservoir shall be by an oil level sight gauge, a low oil level warning light, or similar device and shall be in clear view of the operators normal work stati

35、on. An automatic lubrication system shall be provided for all ways and axis screws. Each lubricant reservoir shall have at least a 24-hour capacity and means for determining fluid level. All oil holes, grease fittings, and filler caps shall be readily accessible. 3.2.10 Interchanseabilitv. All parts

36、 of the end item shall be manufactured to definite standards and tolerances that will provide for the interchangeability of respective replacement parts between end items of the same model. All replacement parts shall be interchangeable with their respective original parts and fit/function with mati

37、ng components. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-3788G 3.3 Construction. The shapers shall be constructed of parts which are new, without defects, and free of repairs. The structure shall withstand all forces encountered during

38、operation of the shqper to its maximum rating and capacity without permanent distortion or failure. 3.3.1 Castinss and forsinss. All castings and forgings shall be free of defects, scale, and mismatching. No processes such as welding, peening, plugging, or filling with solder or paste shall be used

39、for reclaiming any defective part. Such processes may be used only for enhancing surface finish and appearance. 3.3.2 Fasteninq devices. All screws, pins, bolts, and similar parts shall be installed in such a manner as to prevent unintentional change of tightness. Those subject to removal or adjust

40、shall not be swaged, peened, welded, staked, or otherwise permanently deformed. 3.3.3 Surfaces. All surfaces shall be clean and free of harmful or extraneous materials. All edges shall be either rounded or beveled unless sharpness is required to perform a necessary function. Except as otherwise spec

41、ified herein, the condition and finish of all surfaces shall be in accordance with the manufacturers commercial practice. 3.3.4 Weldinq, brazing, or solderinq. Welding, brazing, or soldering shall be employed only where specified in the original design. Any excess material used for such operations s

42、hall be thoroughly removed from the part(s) upon completion of the operations. None of these operations shall be employed as a repair measure for defective parts. 3.3.5 Paintinq. Unless otherwise specified (see 6.2), the paint color and application shall be in accordance with the manufacturers comme

43、rcial pract i ce. 3.3.6 Threads. All threaded parts used on the shapers and their related attachments and accessories shall conform to FED-STD-H28 and the applicable “Detailed Standard“ section referenced therein. 3.3.7 Gears. All gears shall be constructed from a material suitable for the intended

44、purpose. All gears shall be machined and heat treated by a process that will impart the hardness, surface finish, and toughness that will enable the gear train to transmit full rated torque of the drive motor without gear damage, failure, or premature deterioration and wear. 3.3.8 Electromasnetic in

45、terference control. When specified (see 6.2), equipment furnished under this specification shall comply with MIL-STD-461. The equipment and subsystem(s) class and the emission and susceptibility requirements shall be as specified. 6 Provided by IHSNot for ResaleNo reproduction or networking permitte

46、d without license from IHS-,-,- however, this does not authorize submissions of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.2 Classification of inspections. The inspection requirements specified herein are classified as foll

47、ows: a. First article inspection (see 4.4). b. Qual i ty conformance inspect i on (see 4.5) . 4.3 Inspection conditions. Unless otherwise specified (see 6.2), all inspections shall be performed in accordance with the test conditions specified in 4.7.1. 4.4 First article inspection. When a first arti

48、cle inspection is required, it shall be applied to the first article submitted in accordance with 3.1. Unless otherwise specified (see 6.2), first article inspection shall consist of the examination in 4.6 and all tests in 4.7. The machine shall pass the examination and all tests to be accepted. 10

49、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-3788G 4.5 Oualitv conformance inwection. Quality conformance inspection shall be applied to each shaper prior to being offered for acceptance under the contract. Unless otherwise specified (see 6.2), quality conformance inspection shall consist of the examination in 4.6, the tests in 4.7, and the inspection in 4.8. The ma