DLA MIL-PRF-22885 102 D-2010 SWITCH PUSHBUTTON 4-LAMP PUSHBUTTON AND LENS ASSEMBLIES FOR 610 SQUARE (DRIPPROOF SUNLIGHT READABLE EMI RFI SHIELDED).pdf

《DLA MIL-PRF-22885 102 D-2010 SWITCH PUSHBUTTON 4-LAMP PUSHBUTTON AND LENS ASSEMBLIES FOR 610 SQUARE (DRIPPROOF SUNLIGHT READABLE EMI RFI SHIELDED).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-22885 102 D-2010 SWITCH PUSHBUTTON 4-LAMP PUSHBUTTON AND LENS ASSEMBLIES FOR 610 SQUARE (DRIPPROOF SUNLIGHT READABLE EMI RFI SHIELDED).pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5930 INCH-POUND MIL-PRF-22885/102D 4 June 2010 SUPERSEDING MIL-PRF-22885/102C 2 April 2004 PERFORMANCE SPECIFICATION SHEET SWITCH, PUSHBUTTON, 4-LAMP, PUSHBUTTON AND LENS ASSEMBLIES FOR, .610 SQUARE (DRIPPROOF, SUNLIGHT READABLE, EMI/RFI SHIELDED) This specification is approved for use

2、by all Departments and Agencies of the Department of Defense. The requirements for acquiring the switches described herein shall consist of this specification sheet and MIL-PRF-22885. FIGURE 1. PUSHBUTTON STYLES, (UNSEALED) A, B, E, F NOTES: 1. Dimensions are in inches. 2. Unless otherwise stated, t

3、olerances are .010 (0.25 mm) for three place decimals and .03 (0.8 mm) for two place decimals. 3. Lamps shown for reference only. 4. The design configuration is optional within the envelope dimensions shown. INCHES MM .52 13.2 .61 15.5 .71 18.0 1.01 25.6 DIM A SHORT VERSION .71 EXTENDED VERSION 1.01

4、 Lamp Circuit 1 and 4 Style A Without EMI/RFI Shielding Style E With EMI/RFI Shielding Lamp Circuit 3 Style B Without EMI/RFI Shielding Style F With EMI/RFI Shielding Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 2 FIGURE 2. PUSH

5、BUTTON STYLES, (SEALED) C, D, G, H NOTES: 1. Dimensions are in inches. 2. Unless otherwise stated, tolerances are .010 (0.25 mm) for three place decimals and .03 (0.8 mm) for two place decimals. 3. Lamps shown for reference only. 4. The design configuration is optional within the envelope dimensions

6、 shown. INCHES MM .52 13.2 .61 15.5 .66 16.7 .71 18.0 1.01 25.6 DIM A SHORT VERSION .71 EXTENDED VERSION 1.01 Lamp Circuit 1 and 4 Style C Integral Seal Style G Integral Seal/EMI/RFI Shielding Lamp Circuit 3 Style D Integral Seal Style H Integral Seal/EMI/RFI Shielding Provided by IHSNot for ResaleN

7、o reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 3 FIGURE 3. SPARE PART, PUSHBUTTON STYLES, (UNSEALED) A, B, E, F NOTES: 1. Dimensions are in inches. 2. Unless otherwise stated, tolerances are .010 (0.25 mm) for three place decimals and .03 (0.8 mm) for two plac

8、e decimals. 3. The design configuration is optional within the envelope dimensions shown. 4. EMI/RFI screen not shown for clarity. INCHES MM .63 16.0 .69 17.5 .99 25.1 DIM B SHORT VERSION .69 EXTENDED VERSION .99 A Lamp Circuit 1 and 4 Style A Without EMI/RFI Shielding Style E With EMI/RFI Shielding

9、 4/ Lamp Circuit 3 Style B Without EMI/RFI Shielding Style F With EMI/RFI Shielding 4/ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 4 LENS STYLE 3: FRONT LENS PLATE, LAMINATED, TYPE S 3/ FIGURE 4. SPARE PART, FRONT LENS PLATE NO

10、TES: 1. Dimensions are in inches. 2. Unless otherwise stated, tolerances are .010 (0.25 mm) for three place decimals and .03 (0.8 mm) for two place decimals. 3/ For reference only. Lens Style 3 must be procured as total laminated assembly of lens Type S. INCHES MM .030 .76 .047 1.19 .544 13.82 LENS

11、STYLE 1: FRONT LENS PLATE, TYPE N LENS STYLE 2: FRONT LENS PLATE, TYPE W AND C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 5 FIGURE 5. SPARE PART, LAMINATED FILTER, TYPE N AND TYPE W NOTES: 1. Dimensions are in inches. 2. Unles

12、s otherwise stated, tolerances are .010 for three place decimals and .03 for two place decimals. INCHES MM .085 2.16 .262 6.66 .544 13.82 LENS STYLE 4: LAMINATED FILTER LENS STYLE 5: LAMINATED FILTER LENS STYLE 6: LAMINATED FILTER Provided by IHSNot for ResaleNo reproduction or networking permitted

13、without license from IHS-,-,-MIL-PRF-22885/102D 6 FIGURE 6. SPARE PART, LAMINATED FILTER, TYPE C NOTES: 1. Dimensions are in inches. 2. Unless otherwise stated, tolerances are .010 for three place decimals and .03 for two place decimals. INCHES MM .085 2.16 .262 6.66 .544 13.82 LENS STYLE 7: LAMINAT

14、ED FILTER LENS STYLE 8: LAMINATED FILTER LENS STYLE 9: LAMINATED FILTER Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 7 FIGURE 7. SPARE PART, LAMINATED FILTER, TYPE S 3/ NOTES: 1. Dimensions are in inches. 2. Unless otherwise sta

15、ted, tolerances are .010 for three place decimals and .03 for two place decimals. 3/ For reference only. Lens Style 10, 11, and 12 must be procured as total laminated assembly of lens Type S. INCHES MM .065 1.65 .262 6.65 .544 13.82 LENS STYLE 10: LAMINATED FILTER LENS STYLE 11: LAMINATED FILTER LEN

16、S STYLE 12: LAMINATED FILTER Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 8 NOTES: 1. Dimensions are in inches. 2. Unless otherwise stated, tolerances are .010 for three place decimals and .03 for two place decimals. 3. Type S d

17、ividers cannot be ordered separately. 4. Design of lens support optional within envelope dimensions shown. FIGURE 8. Spare part, divider, type W, N and C. (See note 3) INCHES MM .040 1.02 .252 5.40 .545 13.84 .552 14.02 DIM C SHORT VERSION .252 EXTENDED VERSION .552 2-WAY DIVIDER 3-WAY DIVIDER 4-WAY

18、 DIVIDER Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 9 FIGURE 9. SPARE PART, LENS RETAINER NOTES: 1. Dimensions are in inches. 2. Unless otherwise stated, tolerances are .010 for three place decimals and .03 for two place decim

19、als. INCHES MM .19 4.8 .52 13.2 .61 15.5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 10 FIGURE 10. LENS ASSEMBLY DIAGRAM, TYPE N Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

20、MIL-PRF-22885/102D 11 FIGURE 11. LENS ASSEMBLY DIAGRAM, TYPE W Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 12 FIGURE 11. LENS ASSEMBLY DIAGRAM, TYPE C Provided by IHSNot for ResaleNo reproduction or networking permitted without

21、 license from IHS-,-,-MIL-PRF-22885/102D 13 FIGURE 13. LENS ASSEMBLY DIAGRAM, TYPE S 1/ 1/ Lens assembly diagram for Type S displays for reference only. Type S displays shall be procured as complete laminated assemblies. Provided by IHSNot for ResaleNo reproduction or networking permitted without li

22、cense from IHS-,-,-MIL-PRF-22885/102D 14 TABLE I. Illuminated color limits. 3/ Color X 1/ Y 1/ Red (R) .665 SL 2/ .663 .335 .711 .287 .713 SL 2/ Green (G) .300 .560 .300 SL 2/ .365 .560 .365 SL 2/ Yellow (Y) .568 .425 .575 SL 2/ .630 SL 2/ .623 .370 Blue (B) 4/ .250 .330 .250 .420 .330 .330 .330 .42

23、0 White (W) .480 .395 .480 .435 .540 .431 .540 .391 1/ The chromaticities of the colors are expressed as “X“ and “Y“ coordinates on the CIE chromaticity diagram and are within the limits bound by the coordinates listed for each color. 2/ Where intersection occurs with the spectrum locus on the CIE c

24、hromaticity diagram. 3/ Chromaticity values are obtained when switch is illuminated by 4 (T-1 midget-flange base) subminiature lamps of .15 .01 mean spherical candlepower (MSCP) at 5 V dc, 2400K. 4/ Not available on type S with EMI/RFI screen. Provided by IHSNot for ResaleNo reproduction or networki

25、ng permitted without license from IHS-,-,-MIL-PRF-22885/102D 15 REQUIREMENTS: Intended use: As pushbutton and lens assemblies for 4-lamp illuminated pushbutton switches, MIL-S-22885/100 and MIL-PRF-22885/101. Dimensions and configurations: See figures 1 through 13. Pushbutton: Complete pushbutton sh

26、all consist of: 1 - Pushbutton: Includes integral seal and EMI/RFI screen when specified. 1 - Front lens and color filter assembly, lens retainer and divider, as specified. 4 - Lamps: (T-1 submidget-flange base) not included, order separately. Industry Lamp No. 6180 is recommended (5 volt, .060 amps

27、, .15 MSCP). Other lamps are available with various power requirements and illumination results. When using higher wattage lamps, additional heat sinking and air flow must be provided (use extended version of switch), and matrix mounting is not recommended. Lens assemblies: Code 1 consists of: 1 - R

28、etainer 1 - Front lens plate 1 - Laminated filter Code 2 and 3 consist of: 1 - Retainer 1 - Front lens plate 2 - Laminated filters 1 - Divider, 2-way split Code 4, 5, 6, and 7 consist of: 1 - Retainer 1 - Front lens plate 3 - Laminated filters 1 - Divider, 3-way split Code 8 consists of: 1 - Retaine

29、r 1 - Front lens plate 4 - Laminated filters 1 - Divider, 4-way split Materials and finishes: Lens retainer: Lens retainer shall be of a material, which will allow the switch to meet the performance requirements, black paint. Front lens plate and laminated filter: High temperature heat resistant pla

30、stic. Thermal shock test is performed in accordance with MIL-PRF-22885, the maximum temperature shall be +85C. Characteristics: See table IV. Color: See table I. For brightness and chromaticity values, see MIL-S-22885/100 and MIL-PRF-22885/101. Provided by IHSNot for ResaleNo reproduction or network

31、ing permitted without license from IHS-,-,-MIL-PRF-22885/102D 16 Qualification inspection: Required as part of the 4-lamp illuminated pushbutton switch, M22885/100 or /101. Group A inspection: Shall be in accordance with MIL-PRF-22885, visual and mechanical only. Part number: Short version: M22885/1

32、02- (dash number from table II). Extended version: M22885/102E (dash number from table II). For acquisition of government spares, M22885/102 or M22885/102E (dash numbers from tables II and III) shall be used. Part numbers: Part numbers for complete pushbutton are assigned as follows: Extended versio

33、n: M22885/102E 25 S 2GR Short version: M22885/102- 25 S 2GR These part numbers are for the convenience of users only and do not include legends. Acquire legend portion of assembly separately from QPL source. For acquisition of government spares, use dash numbers shown in tables II and III. TABLE II.

34、 Pushbutton configuration and dash numbers. Display type Pushbutton style Lamp 4/ circuit N W C S 1/ Standard pushbutton no seal, no EMI/RFI shielding 01 09 17 25 33 A 1 and 4 02 10 18 26 34 B 3 Standard pushbutton with seal, no EMI/RFI shielding 03 11 19 27 3/ C 1 and 4 04 12 20 28 D 3 Standard pus

35、hbutton with EMI/RFI shielding, no seal 05 13 21 29 35 E 1 and 4 06 14 22 30 36 F 3 Standard pushbutton with seal and EMI/RFI shielding 07 15 23 31 3/ G 1 and 4 08 16 24 32 H 3 1/ For pushbutton spare parts, order 33 through 36, as required. Does not include lens retainer, lens assemblies, or divide

36、rs. 2/ Reference letter code for display type. Must be used in conjunction with appropriate dash numbers; i.e., -25S, -01N, -09W, etc. 3/ Spare pushbutton styles C, D, G, and H not available. 4/ Lamps circuits per MIL-S-22885/100 and MIL-PRF-22885/101, for reference only. Specification number Sunlig

37、ht readable Display Display code 2: Horiz. split, green color filter top half, red color filter bottom half Display config. (see table V) Display type (see table IV) 2/ Pushbutton config. (see table II) Standard pushbutton, no seal, no EMI/RFI shielding, Lamp Ckt. 1 and 4, Display Type S Provided by

38、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 17 TABLE III. Spare part configuration part number. Part no. M22885/102- Display type Lens 3/ code Style 4/ number Color Description 37 N All 1 Clear Front lens plate Painted black 38 W, C All 2

39、 Clear Front lens plate 39 N, W 1 4 White Filter, full display 40 “ “ “ Red “ 41 “ “ “ Green “ 42 “ “ “ Yellow “ 43 “ “ “ Blue “ 44 “ 2, 3, 4, 5, 6, 7 5 White Filter, half display 45 “ “ “ Red “ 46 “ “ “ Green “ 47 “ “ “ Yellow “ 48 “ “ “ Blue “ 49 “ 4, 5, 6, 7, 8 6 White Filter, qtr. display 50 “ “

40、 “ Red “ 51 “ “ “ Green “ 52 “ “ “ Yellow “ 53 “ “ “ Blue “ 54 C 1 7 White Filter, full display 55 “ “ “ Red “ 56 “ “ “ Green “ 57 “ “ “ Yellow “ 58 “ “ “ Blue “ 59 “ 2, 3, 4, 5, 6, 7 8 White Filter, half display 60 “ “ “ Red “ 61 “ “ “ Green “ 62 “ “ “ Yellow “ 63 “ “ “ Blue “ See footnotes at end

41、of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 18 TABLE III. Spare part configuration part number - Continued. Part no. M22885/102- Display type Lens 3/ code Style 4/ number Color Description 64 C 4, 5, 6, 7, 8 9 White F

42、ilter, qtr. display 65 “ “ “ Red “ 66 “ “ “ Green “ 67 “ “ “ Yellow “ 68 “ “ “ Blue “ 69 All 2, 3 - - - - - - Divider, 2-way 70 All 4, 5, 6, 7 - - - - - - Divider, 3-way 71 All 8 - - - - - - Divider, 4-way 72 All All - - - - - - Lens retainer 73 S All All All Lens assembly 1/ S All 3 2/ - - - Front

43、lens plate 1/ S 1 10 2/ All Filter, full display 1/ S 2, 3, 4, 5, 6, 7 11 2/ All Filter, half display 1/ S 4, 5, 6, 7, 8 12 2/ All Filter, qtr. display 1/ Type S displays shall be procured as complete assemblies only, that consist of front lens plate, filters, and dividers. To order, specify: M22885

44、/102-73S or M22885/102E73S (plus display configuration and color(s) as required. 2/ Lens style 3, 10, 11, and 12 are shown for reference only. 3/ see table V and figures 10, 11, 12, and 13. 4/ See figures 4, 5, 6 and 7. 5/ When ordering extended dividers, specify M22885/102E (dash number 69, 70, or

45、71, as required). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/102D 19 TABLE IV. Display type. Display type Description N LIGHTER LETTERS: Letters appear white on a black background until illuminated and then letters appear in color,

46、 background remains black. W LIGHTED BACKGROUND: Letters appear black on a white background until illuminated and then background appears in color, letters remain black. S SUNLIGHT READABLE: Letters are not legible until illuminated and then letters appear in color, background remains black. When il

47、luminated, lighted letters are readable in direct sunlight. C COLORED BACKGROUND: Letters appear black against a colored background until illuminated and then background appear in lighted color, letters remain black. TABLE V. Display configuration. 2/ Display code 1/ 3/ Display 1X 2XX 3XX 4XXX 5XXX

48、6XXX 7XXX 8XXXX 1/ Display codes shown are for pushbuttons without color filters. Replace Xs with the color symbols of table I in sequence shown. 2/ Legends shall be procured separately from a source listed on the qualified products lists. 3/ Display codes 3XX through 8XXXX not available with pushbutton styles B, D, F, an