DLA DSCC-DWG-09002-2009 RESISTOR FIXED FILM PRECISION HIGH OHMIC VALUES.pdf

《DLA DSCC-DWG-09002-2009 RESISTOR FIXED FILM PRECISION HIGH OHMIC VALUES.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-09002-2009 RESISTOR FIXED FILM PRECISION HIGH OHMIC VALUES.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LT DESCRIPTION DATE APPROVEDPrepared in accordance with ASME Y14.100 Source control drawing REV REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Andrew R. Ernst DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH CHECKED BY Andrew R. Ernst APPROVED BY Michael A. Radecki TITLE RESIS

2、TOR, FIXED, FILM, PRECISION, HIGH OHMIC VALUES SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09002 Original date of drawing 13 February 2009 REV PAGE 1 OF 8 AMSC N/A 5905-E679 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS

3、, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09002 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a precision, fixed, film, high ohmic value resistors. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 09002 C Y 121R010 B | | | | | Drawing Terminal Chara

4、cteristic and 10.0 ppm/oC from +125oC to +175oC. 300 volts maximum working voltage. S and Z - Nonhermetically sealed - Resistance temperature characteristic (referenced to +25oC) = 2.0 ppm/oC up to and including +175oC. 300 volts maximum working voltage. TABLE II. Terminal spacing. Characteristic Co

5、nfiguration Y and Z A T and S B 3.3.3 Resistance value designations. Resistance value designations shall be in accordance with MIL-PRF-55182/9. 3.3.3.1 Resistance. The resistance limits shall be as follows: 121,001 kilohms to and 200 kilohms. 3.3.4 Resistance tolerance. The resistance tolerance is i

6、dentified by a single letter in accordance with table III. TABLE III. Resistance tolerance. Symbol Resistance tolerance (percent) V T A B D F 0.005 0.01 0.05 0.1 0.5 1.0 3.4 Power rating. The power rating shall be 0.30 watt at +125C. For operation at temperature higher than +125C, derate in accordan

7、ce with figure 2. 3.5 Voltage rating. The maximum continuous working voltage shall not exceed 300 volts. 3.6 Thermal shock. When resistors are tested as specified in accordance with MIL-PRF-55182, there shall be no evidence of mechanical damage; the change in resistance shall not exceed 0.05 percent

8、 for thermal shock and overload tests combined. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09002 REV PAGE 5 NOTE: These curves indicate the percentage of nominal watta

9、ge to be applied at temperatures higher than +125C. However, at no time shall the applied voltage exceed the maximum for each style. FIGURE 2. Derating curve for high ambient temperatures. 3.7 Short time overload. When resistors are tested as specified in accordance with MIL-PRF-55182, with an overl

10、oad of 6.25 times rated power for 5 seconds, there shall be no evidence of arcing, burning, or charring; the change in resistance shall not exceed 0.05 percent for thermal shock and overload tests combined (see 3.6). The maximum voltage shall not exceed 450 volts. 3.8 Low temperature operation. When

11、 resistors are tested as specified in accordance with MIL-PRF-55182, there shall be no evidence of mechanical damage. The change in resistance shall not exceed 0.05 percent. 3.9 Terminal strength. When resistors are tested as specified in 4.5, there shall be no evidence of breaking or loosening of t

12、erminals from the resistor form, or chipping of coating, or other evidence of mechanical damage. The change in resistance shall not exceed 0.02 percent. 3.10 Dielectric withstanding voltage. When resistors are tested as specified in 4.6, there shall be no evidence of flashover, mechanical damage, ar

13、cing, or insulation breakdown. The change in resistance shall not exceed 0.02 percent. 3.11 Resistance to soldering heat. When resistors are tested as specified, there shall be no evidence of mechanical damage. The change in resistance shall be 0.02 percent. 3.12 Moisture resistance. When resistors

14、are tested as specified in 4.7, there shall be no evidence of mechanical damage. The change in resistance shall not exceed 0.05 percent. In addition, the dielectric withstanding voltage shall be specified in 3.10, and the insulation resistance shall be 100 megohms, minimum. 3.13 Shock (specified pul

15、se). When tested as specified in accordance with MIL-PRF-55182, there shall be no evidence of mechanical damage or electrical discontinuity. The change in resistance shall not exceed 0.01 percent. There shall be no electrical discontinuity during test. 3.14 Vibration, high frequency. When resistors

16、are tested as specified in accordance with MIL-PRF-55182, there shall be no evidence of mechanical damage or electrical discontinuity. The change in resistance shall not exceed 0.02 percent. There shall be no electrical discontinuity during test. Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENT

17、ER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09002 REV PAGE 6 3.15 High temperature exposure. When resistors are tested as specified in accordance with MIL-PRF-55182, there shall be no evidence of electrical or mechanical damage. The change in resistance shall not exceed 0.5 perce

18、nt. Following this test, the dielectric withstanding voltage shall be as specified in 3.10, and the insulation resistance shall be 1,000 megohms, minimum. 3.16 Low temperature storage. When resistors are tested as specified in accordance with MIL-PRF-55182, there shall be no evidence of electrical o

19、r mechanical damage. The change in resistance shall not exceed 0.05 percent. 3.17 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed wit

20、h a minimum of 3 percent lead, by mass (see 6.3). 3.18 Life. When resistors are tested as specified in accordance with MIL-PRF-55182, there shall be no evidence of mechanical damage to the resistance element or enclosure. The change in resistance between initial measurement and any of the succeeding

21、 measurements up to and including 2,000 hours shall not exceed 0.05 percent. 3.19 Voltage coefficient. When resistors are tested as specified in accordance with MIL-PRF-55182, the voltage coefficient shall not exceed 0.0005 percent. 3.20 Marking. Marking shall be in accordance with MIL-STD-1285, exc

22、ept the PIN shall be as specified in 1.2, with the manufacturers CAGE number or trade mark and date code. 3.21 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the ma

23、terials meet or exceed the operational and maintenance requirements, and promote economically advantageous life cycle costs. 3.22 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-55182/9 Qualified Product List for at

24、least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.22.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.23 Wor

25、kmanship. Resistors shall be processed in such a manner as to be uniform in quality and free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Reliability assurance program. The reliability assurance program specified in MIL-PRF-55182 and maintained in accordance

26、 with MIL-STD-790 are not applicable to this document. 4.2 Qualification inspection. Qualification inspection in accordance with MIL-PRF-55812 is not applicable to this document. 4.2.1 Failure rate qualification. Failure rate qualification in accordance with MIL-PRF-55182 and MIL-STD-690 is not appl

27、icable to this document. 4.3 Conformance inspection. 4.3.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A (ER level) and group B inspections. 4.3.1.1 Group A inspection. Group A inspection (ER level) shall be in accordance with MIL-PRF-55182. Part per

28、 million testing and verification as specified in MIL-PRF-55182 is not applicable to this document. 4.3.1.2 Group B inspection. Group B inspection shall be in accordance with MIL-PRF-55182. 4.3.1.2.1 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance wit

29、h group B requirements in lieu of performing group B tests (see 6.2d). 4.4 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-55182. Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09002 REV PAGE 7

30、 4.5 Terminal strength. Resistors shall be tested in accordance with MIL-PRF-55182, the following details and exceptions shall apply: a. The body be clamped and the lead pulled in a direction parallel and along the axis or the lead (see figure 3). b. Applied force: 2 pounds. FIGURE 3. Metal strap fo

31、r dielectric withstanding voltage, moisture resistance and insulation resistance. 4.6 Dielectric withstanding strength. Resistors shall be tested in accordance with MIL-PRF-55182, the following details and exceptions shall apply: a. Atmospheric pressure: 300 volts rms. b. Barometric pressure (reduce

32、d): 200 volts rms. The resistor body shall be held between metal straps (see figure 3). 4.7 Moisture resistance. Resistors shall be tested in accordance with MIL-PRF-55182, except the resistor body shall be held between metal strips during polarization (see figure 3). 5. PACKAGING 5.1 Packaging. For

33、 acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. P

34、ackaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packagin

35、g files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Resistor used in electronic circuits where the resistance temperature coefficie

36、nt must be tightly controlled. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery: One copy of the conformance inspection data or a certificate of compliance that parts have passed conformance inspection with each s

37、hipment of parts by the manufacturer. c. Requirements for packaging and packing (see 5.1). d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A

38、 CODE IDENT NO. 037Z3 DWG NO. 09002 REV PAGE 8 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical op

39、erating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refe

40、r to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Low tolerance resistors. In low tolerance resistors (.005 and .01), resistance shifts due to high humidity are normal to precision, fixed, resistors. Before being considered out of tolerance, resistors should be condit

41、ioned in a dry oven at +125oC for 1 hour, +15 minutes, -0 minutes followed by 2 hours, +30 minutes, -0 minutes stabilization at ambient temperature before measurement. Resistors which continue to be out of tolerance after the above conditioning process are considered rejects. 6.5 Electrostatic charg

42、e. Under several combinations of conditions, these resistors can be electrically damaged, by electrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 which specifi

43、es a preventive packaging procedure. 6.6 Pulse applications. Designers are CAUTIONED on using these resistors in high power pulse applications. Since they have not been qualified nor tested for such applications. These resistors only see a one time pulse (Overload) as part of the group B inspection

44、of this specification. These resistors are subject to damage and premature failures when they see excessive pulsing. 6.7 User of record. Coordination of this document for future revisions is coordinated only with the approved source of supply and the users of record of this document. Requests to be

45、added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. 6.8 Approved source of supply. Approved source of supply is listed herein. Additional sources w

46、ill be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing PIN 09002-* Vendors similar designation or type numbe

47、r 1/ Vendor CAGE Vendors name and address Terminal type: C and N. Characteristic: S, T, Y, and Z. Configuration: A and B. Resistance values: 121,001 ohms to 200 kilohms. Resistance tolerances: A, B, D, F, T and V. MAR*-13 MCR*-13 SB481 Vishay Precision Resistors 63 Lancaster Avenue Malvern, PA 19355 Plants: Alpha Electronics 238-1 Itaizawa Nakatashiro Yurihonjo Akita, 018-0901 Japan 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS