DLA A-A-59213 A-2009 SPLICE CONNECTORS.pdf

《DLA A-A-59213 A-2009 SPLICE CONNECTORS.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59213 A-2009 SPLICE CONNECTORS.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. FSC 5940 INCH-POUND A-A-592

2、13A 28 May 2009 SUPERSEDING A-A-59213 18 May 1998 COMMERCIAL ITEM DESCRIPTION SPLICE CONNECTORS The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers splice connectors, referred

3、 to herein as connectors, for providing pressure contact between current carrying conductors of an electrical wiring system. Connectors are for use as electrical connectors in dry locations and are not for grounding purposes in wet or damp locations. 2. CLASSIFICATION. The splice connectors covered

4、by this CID shall be of the following types, classes, kinds, and styles: 2.1 Type. The connector shall be one of the following types (see 7.3(b): Type I - Twist-on Type II - Crimp or compression Type III - Threaded or bearing 2.2 Class. The connector shall be one of the following classes (see 7.3(c)

5、: Class 1 - Insulated Class 2 - Uninsulated 2.3 Kind. The connector shall be one of the following kinds (see 7.3(d): Kind AL - Aluminum to aluminum Kind CU - Copper to copper Kind AL-CU - Aluminum to copper Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

6、-,-,-A-A-59213A 2 2.4 Style. The connector shall be one of the following styles (see 7.3(e): Style A - Butt connection Style C - Combined “T“ and straight connection Style D - “T“ connection Style E - Parallel connection Style F - Tap connection Style G - Pigtail connection 3. SALIENT CHARACTERISTIC

7、S 3.1 Description. The connectors shall provide contact between current carrying parts of an electrical wiring system. Unless otherwise specified herein, the connectors shall conform to standard manufacturing requirements for pressure type wire connectors. 3.1.1 Types. The types of connectors shall

8、be as follows: 3.1.1.1 Type I. Type I connectors shall be class 1, kind CU, style G twist-on type connectors in which the pressure to provide contact between the current carrying conductors is applied by twist-on spring or equivalent device. Typical conductor capacities of type I connectors are prov

9、ided in table I. TABLE I. Size of type I connectors (reference). Typical conductor capacities - AWG # Minimum Maximum 2 - #18 2 - #12, 3 - #14 2 - #14 4 - #12, 2 - #10 2 - #12 4 - #10, 2 - #8 Common sizes 2 - #10 3 - #8, 2 - #6 3.1.1.2 Type II. Type II connectors shall be crimp or compression type c

10、onnectors in which the pressure to provide contact between the current carrying conductors is applied by crimp(s), or other means of deformation of the connector and conductors junction interface and shall be class 1 or class 2. Type II, style E connectors shall be of the compression type only. 3.1.

11、1.3 Type III. Type III connectors shall be slip-on type connectors in which the pressure to provide contact between the current carrying conductors is applied by a set screw, split bolt, or insulation piercing device and shall be class 1 or class 2. 3.1.2 Classes. The classes of connectors shall be

12、as follows: 3.1.2.1 Class 1. Class 1 connectors shall be insulated connectors which, when applied to conductors, shall provide a fully insulated joint. An insulated connector shall be rated for either 300 volts or 600 volts (1,000 volts in signs and fixtures), as specified (see 7.3(f). Provided by I

13、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59213A 3 3.1.2.2 Class 2. Class 2 connectors shall be uninsulated connectors. 3.1.3 Kinds. Connector kinds shall be suitable for joining the conductor material combinations as follows: 3.1.3.1 Kind AL. Kind AL c

14、onnectors shall be suitable for use in connecting aluminum to aluminum conductors or copper clad aluminum to copper or copper clad aluminum conductors. 3.1.3.2 Kind CU. Kind CU connectors shall be suitable for use in connecting copper to copper conductors. 3.1.3.3 Kind AL-CU. Kind AL-CU connectors s

15、hall be suitable for use in connecting aluminum to copper or copper clad aluminum conductors or copper clad aluminum to copper or copper clad aluminum conductors for dry locations only. 3.1.3.4 Oxide inhibitor. When specified (see 7.3(g), an oxide inhibitor shall be provided with kind AL and kind AL

16、-CU connectors to inhibit corrosion of aluminum conductor surfaces. 3.1.4 Styles. Styles shall be as described herein. 3.1.4.1 Style A. Style A connectors shall be suitable for use in providing a butt connection between conductors. 3.1.4.2 Style C. Style C connectors shall be suitable for use in pro

17、viding a combined “T“ connection and a straight (butt) connection between conductors. 3.1.4.3 Style D. Style D connectors shall be suitable for use in providing a “T“ connection to a straight through conductor. 3.1.4.4 Style E. Style E connectors shall be suitable for making a connection between par

18、allel conductors. 3.1.4.5 Style F. Style F connectors shall by suitable for use in providing a parallel or Y-type connection to a straight through conductor. 3.1.4.6 Style G. Style G connectors shall be suitable for use in providing a pigtailed type connection between ends of conductors. 3.1.5 Alumi

19、num conductor connections. Aluminum conductor connections shall have the following conductor size and use limitations: Style A, C, D, E, F - AWG #12 and larger aluminum Style G Types II and III - AWG #12 through AWG #6 Type I - Not applicable Provided by IHSNot for ResaleNo reproduction or networkin

20、g permitted without license from IHS-,-,-A-A-59213A 4 3.1.6 Copper conductor connections. Copper conductor connections shall have conductor size and use limitations in accordance with UL 486A-486B, “Wire Connectors“, and UL 486C, “Splicing Wire Connectors“, unless otherwise specified herein. 3.2 Sta

21、ndard commercial product. The connectors shall, as a minimum, be in accordance with the requirements of this CID and shall be the manufacturers standard commercial product. Additional or better features which are not specifically prohibited by this CID but which are a part of the manufacturers stand

22、ard commercial product, shall be included in the connectors being furnished. A standard commercial product is a product which has been sold or is being currently offered for sale on the commercial market through advertisements or manufacturers catalogs, or brochures, and represents the latest produc

23、tion model. 3.3 Design and construction. The design and construction of the connectors shall be such as to prevent conditions which may be hazardous to personnel or deleterious to electrical circuitry and equipment. 3.3.1 Style G twist-on design. Style G twist-on connectors shall contain a tapered c

24、oil insert secured inside a closed end insulator. The coil shall be so designed that increasing pressure is exerted upon joining conductor surfaces as the insulator cap is tightened. The coil diameter and cap shall be designed so that the coil is free to expand or contract during or after wire inser

25、tion and during operation at rated loads. The coil shall be of a hard drawn, square cross section, spring steel wire with a corrosion-resistant finish. The insulator cap shall be of a flame-retardant material with a temperature rating of not less than 221 F (105 C). Type I connectors shall be restri

26、cted to use with copper (kind CU). 3.3.2 Connector size. Connector sizes shall be of adequate size and kind to accommodate the junction wire kinds and sizes specified (see 7.3(h) and table I). Solid wire sizes shall be limited to AWG #8 and smaller. Minimum conductor size shall be AWG #22. 4. REGULA

27、TORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). Unless otherwise specified herein, all equipment, material, and articles inco

28、rporated in the work covered by this CID are to be new and fabricated using materials produced from recovered materials to the maximum extent possible without jeopardizing the intended use. The term “recovered materials“ means materials which have been collected or recovered from solid waste and rep

29、rocessed to become a source of raw materials, as opposed to virgin raw materials. Unless otherwise specified, none of the above shall be interpreted to mean that the use of used or rebuilt products are allowed under this CID. 4.2 Metric products. Products manufactured to metric dimensions will be co

30、nsidered on an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest version of IEEE/ASTM SI 10, “American National Standard for Use of the International Systems of Units (SI): The Modern Metric Syst

31、em“, and all other requirements of this CID including form, fit and function are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59213A 5 If a product is manufactured to metric dimensions and these dimensions exceed the tolerances specified

32、in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salien

33、t characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability.

34、The product offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. Preservation, packing, and marking shall be as specified in the acquisition order (see 7.3(i). 7. NOTES 7.1 Part or identification number (PIN

35、). The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. Example of reference part number: AA59213 - 11BG CID number Kind: A - Kind AL - Aluminum to aluminum B - Kind CU - Copper to copper C - Kind AL-CU - Aluminum to copper Class: 1 - Class

36、 1 - Insulated 2 - Class 2 - Uninsulated Type: 1 - Type I - Twist-on 2 - Type II - Crimp or compression 3 - Type III - Threaded or bearing AA59213 - X X X X Style: A - Style A - Butt connection C - Style C - Combined “T“ and straight connection D - Style D - “T“ connection E - Style E - Parallel con

37、nection F - Style F - Tap connection G - Style G - Pigtail connection Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59213A 6 7.2 Sources of documents. 7.2.1 FAR. The FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pit

38、tsburgh, PA 15250-7954. Electronic copies of FAR documents may be obtained from http:/www.arnet.gov/far/. 7.2.2 ASTM standards. Copies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies of ASTM standard

39、s may be obtained from http:/www.astm.org/. 7.2.3 IEEE standards. Copies of IEEE standards may be obtained from IEEE, 445 Hoes Lane, Piscataway, NJ 08854-1331. Electronic copies of IEEE standards may be obtained from http:/www.ieee.org/. 7.2.4 UL standards. Copies of UL standards may be obtained fro

40、m Underwriter Laboratories Inc., 333 Pfingsten Road, Northbrook, IL 60062-2096. Electronic copies of UL standards may be obtained from http:/ 7.3 Ordering data. The acquisition order should specify the following information: a. CID document number, revision, and CID PIN. b. Type of connector (see 2.

41、1). c. Class of connector (see 2.2). d. Kind of connector (see 2.3). e. Style of connector (see 2.4). f. Voltage rating required (see 3.1.2.1). g. When an oxide inhibitor is provided (see 3.1.3.4). h. Conductor wire kinds and sizes and combination (see 3.3.2). i. Preservation, packing, and marking (

42、see 6.1). 7.4 Metric units. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system should be used independently of the

43、other. Combining values from the two systems may result in non-conformance with the standard. 7.5 Subject term (key word) listing. current electrical pressure contact wiring Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59213A 7 MILITARY INTERE

44、STS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: Army - CR Navy - YD Air Force - 85 DLA - GS GSA - FAS Review Activities: Navy - AS Air Force - 03, 99 Preparing Activity: DLA - GS4 (Project 5940-2009-001) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-