DIN EN 13245-1-2010 Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1 Designation of PVC-U profiles German version EN 13245-1 2010《塑.pdf

《DIN EN 13245-1-2010 Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1 Designation of PVC-U profiles German version EN 13245-1 2010《塑.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13245-1-2010 Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1 Designation of PVC-U profiles German version EN 13245-1 2010《塑.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、November 2010 Translation by DIN-Sprachendienst.English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 83.140.99!$l23“1731516www.din.deDDIN EN 13245-1Plastics Unplasticized poly(vinyl chloride) (PVC-U) profiles for buildingapplications Part 1: Designation of PVC-U profilesEnglish translation of DIN EN 13245-1:2010-11Kunststoffe Profile aus weichmacherfreiem Polyvinylchlorid (PVC-U) fr die Anwendun

3、g imBauwesen Teil 1: Bezeichnung von Profilen aus PVC-UEnglische bersetzung von DIN EN 13245-1:2010-11Plastiques Profils en poly(chlorure de vinyle) non plastifi (PVC-U) pour applications dans lebtiment Partie 1: Dsignation des profils en PVC-UTraduction anglaise de DIN EN 13245-1:2010-11SupersedesD

4、IN EN 13245-1:2004-12www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.2511.10 DIN EN 13245-1:2010-11 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 249 “Plast

5、ics” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was the Normenausschuss Kunststoffe (Plastics Standards Committee), Working Committee NA 054-04-07 AA Kunststoff-Fensterprofile. Amendments This standard differs from DIN EN 13245-1:2004-12 as follows: a) Claus

6、e 1 ”Scope” has been modified (the standard is applicable to light coloured and coloured PVC-U profiles); b) Clause 2 “Normative references” has been extended and updated; c) Clause 3 “Terms and definitions” has been extended (e.g. different types of profiles have been included); d) in Subclause 5.1

7、, Table 2 “Preparation of test specimens” has been included; e) the detailed description of the “nominal linear mass” (5.3) has been included as a new Annex A; f) the heading of Subclause 5.6 has been changed to read “Durability”; g) Subclause 5.6.3 “Methods for assessing of ageing” has been further

8、 subdivided and extended; h) Table 5 in Subclause 5.6.4 “Codification for properties after ageing” has been revised and extended (in particular with regard to type requirements); i) Clause 6 “Required characteristics for Type 3 and Type 4 profiles” has been added; j) Clause 7 “Optional characteristi

9、cs” has been added; k) Annex C “Determination of peel strength” has been added; l) the standard has been brought in line with the current rules of presentation. Previous editions DIN EN 13245-1: 2004-12 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13245-1 June 2010 ICS 83.140.99 Supersedes E

10、N 13245-1:2004English Version Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1: Designation of PVC-U profiles Plastiques - Profils en poly(chlorure de vinyle) non plastifi(PVC-U) pour applications dans le btiment - Partie 1: Dsignation des profils en

11、PVC-U Kunststoffe - Profile aus weichmacherfreiem Polyvinylchlorid (PVC-U) fr die Anwendung im Bauwesen -Teil 1: Bezeichnung von Profilen aus PVC-U This European Standard was approved by CEN on 19 May 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the

12、 conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists i

13、n three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodie

14、s of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United King

15、dom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13245-1:2010: EEN 1

16、3245-1:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .54 Designation of PVC-U profiles 65 Codification system for Data block 3 to Data block 5 75.1 Vicat softening temperature (Data block 3) 75.2 Modulus of elasticity in flexure (Data block 3) .75.3 Nomi

17、nal linear mass (Data block 4) .85.4 Heat reversion at 100 C (Data block 4) .85.5 Impact resistance (Data block 4) 85.6 Durability (Data block 5) 96 Required characteristics for Type 3 and Type 4 profiles . 136.1 Resistance to cross cut (only for Type 4 profiles) . 136.2 Thermal resistance (only for

18、 Type 3 and Type 4 profiles) 136.3 Water vapour resistance (only for Type 3 and Type 4 profiles, intended to be used for inside building applications) 136.4 Peel strength (only for Type 3 profiles) . 137 Optional characteristics . 137.1 Resistance to staining 137.2 Appearance and finishing of the co

19、ating (only for Type 3 and Type 4 profiles) 148 Example of the designation of a PVC-U profile . 149 Use of reprocessable and recyclable material 15Annex A (normative) Determination of the linear mass . 16A.1 Apparatus 16A.2 Test specimens . 16A.3 Procedure 16A.4 Calculation and expression of results

20、 16Annex B (normative) Determination of the impact resistance 17B.1 Principle . 17B.2 Apparatus 17B.3 Test specimens . 17B.4 Conditioning 18B.5 Procedure 18B.6 Expression of results . 19Annex C (normative) Determination of peel strength . 20C.1 Principle . 20C.2 Apparatus 20C.3 Preparation of test p

21、ieces 21C.4 Conditioning 21C.5 Procedure 21C.6 Test report . 22Bibliography . 23DIN EN 13245-1:2010-11 EN 13245-1:2010 (E) 3 Foreword This document (EN 13245-1:2010) has been prepared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This European Standard shall

22、be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of the elements of this docu

23、ment may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13245-1:2004. EN 13245, Plastics Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications, consists of the follow

24、ing parts: Part 1: Designation of PVC-U profiles Part 2: PVC-U profiles and PVC-UE profiles for internal and external wall and ceiling finishes Part 3: Designation of PVC-UE profiles It is a revision of EN 13245-1:2004 with the extension of the scope to: light coloured PVC-U profiles with or without

25、 a laminated foil or a lacquered-coating; coloured PVC-U profiles, obtained by a mono-extrusion or a co-extrusion process, with or without laminated foil or with lacquered-coating. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are

26、bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai

27、n, Sweden, Switzerland and the United Kingdom. DIN EN 13245-1:2010-11 EN 13245-1:2010 (E) 4 1 Scope This European Standard establishes a system of designation for profiles made of unplasticized poly(vinyl chloride) (PVC-U) intended to be used for building applications. This part is applicable to lig

28、ht coloured and coloured PVC-U profiles, obtained by a mono-extrusion or a co-extrusion process, with or without a laminated foil or with a lacquered-coating. It specifies test methods and test parameters. This method of designation is intended to be used in product specification when the applicatio

29、n is specified. NOTE It is recommended to use this method for the designation of PVC-U profiles for information related to technical literature of the manufacturer, not for the marking of the products. Profiles for the management of electrical power cables, communication cables and power track syste

30、ms used for the distribution of electrical power, profiles for windows or doors and profiles for guttering are not covered by this European Standard.1)2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edit

31、ion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 438-2:2005, High-pressure decorative laminates (HPL) Sheets based on thermosetting resins (usually called Laminates) Part 2: Determination of properties EN 477:1995, Unplas

32、ticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors Determination of the resistance to impact of main profiles by falling mass EN 478, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors Appearance after exposure at 150 C Test met

33、hod EN 479, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors Determination of heat reversion EN 513:1999, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors Determination of the resistance to artificial weathering EN 201

34、05-A02, Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour (ISO 105-A02:1993) EN ISO 105-A01:2010, Textiles Tests for colour fastness Part A01: General principles of testing (ISO 105-A01:2010) EN ISO 178, Plastics Determination of flexural properties (ISO 178:2001

35、) EN ISO 306:2004, Plastics Thermoplastic materials Determination of Vicat softening temperature (VST) (ISO 306:2004) EN ISO 472:2001, Plastics Vocabulary (ISO 472:1999) 1) Profiles that are excluded are in the scopes of standards prepared by CEN/TC 33, CENELEC/TC 213 or CEN/TC 128. DIN EN 13245-1:2

36、010-11 EN 13245-1:2010 (E) 5 EN ISO 1043-1:2001, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001) EN ISO 1163-2, Plastics Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials Part 2: Preparation of test specimens

37、 and determination of properties (ISO 1163-2:1995) EN ISO 2409, Paints and varnishes Cross-cut test (ISO 2409:2007) EN ISO 2813, Paints and varnishes Determination of specular gloss of non-metallic paint films at 20, 60 and 85 (ISO 2813:1994, including Technical Corrigendum 1:1997) EN ISO 4624, Pain

38、ts and varnishes Pull-off test for adhesion (ISO 4624:2002) EN ISO 4892-2:2006, Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc lamps (ISO 4892-2:2006) EN ISO 8256:2004, Plastics Determination of tensile-impact strength (ISO 8256:2004) ISO 7724-1:1984, Paints and varnishes

39、 Colorimetry Part 1: Principles ISO 7724-2:1984, Paints and varnishes Colorimetry Part 2: Colour measurement ISO 7724-3:1984, Paints and varnishes Colorimetry Part 3: Calculation of colour differences 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN IS

40、O 472:2001 and EN ISO 1043-1:2001 and the following apply. 3.1 PVC-U profile profile made of unplasticized poly(vinyl chloride) (PVC-U) material NOTE It applies to profiles made of non-cellular material as opposed to cellular material. 3.2 Type of profile 3.2.1 Type 1 profile PVC-U profile obtained

41、by a mono-extrusion process (coloured in the mass) 3.2.2 Type 2 profile PVC-U profile obtained by a co-extrusion process 3.2.3 Type 3 profile PVC-U profile as Type 1 or Type 2 with laminated foil 3.2.4 Type 4 profile PVC-U profile as Type 1 or Type 2 with lacquer-coating 3.3 sight surface surface of

42、 a profile that is exposed to view, when the PVC-U profile is installed DIN EN 13245-1:2010-11 EN 13245-1:2010 (E) 6 3.4 coating covering layer on the sight surface of a PVC-U profile, e.g. a co-extruded layer, a lacquer-coating or a laminated foil 3.5 laminated foil plastic layer bonded with an adh

43、esive or under pressure and temperature to cover a surface of a PVC-U profile 3.6 co-extrusion durable bonding of two thermoplastics e.g. unplasticized polyvinylchloride (PVC-U) and poly(methyl methacrylate) (PMMA) that are melted in separated extruders and fused together in the profile tool 3.7 lac

44、quer-coating one or several layer(s) of lacquer (e.g. acrylic or polyurethane resin) or varnish (clear coating material) that cover(s) a PVC-U profile 3.8 radiant exposure time integral of irradiance, measured in joules per square metre (J/m2) ISO 9370:2009 4 Designation of PVC-U profiles The PVC-U

45、profiles are designated in accordance with a classification system of their characteristics. The designation consists of a description block and five data blocks as given in Table 1. DIN EN 13245-1:2010-11 EN 13245-1:2010 (E) 7 Table 1 Designation of PVC-U profiles Description block Profile EN 13245

46、-1 Data block 1: Material and profile type identification PVC-U Type 1, Type 2, Type 3 a or Type 4aFor types of profiles See 3.2 Data block 2: Intended application One or more following codes depending on the intended application: For outside building applications: E For inside building applications

47、: I Data block 3: Material properties Vicat softening temperature (VST): See 5.1 Modulus of elasticity in flexure: See 5.2 Data block 4: Profile properties Nominal linear mass: See 5.3 Heat reversion at 100 C: See 5.4 Impact resistance: See 5.5 Data block 5: Durability See 5.6 aFor Type 3 or Type 4

48、profiles, the requirements given in 6.1 to 6.4 shall be fulfilled, as applicable. 5 Codification system for Data block 3 to Data block 5 5.1 Vicat softening temperature (Data block 3) The Vicat softening temperature (VST) shall be measured in accordance with EN ISO 306:2004, Method B50, using 4 mm t

49、hick test specimens, prepared according to EN ISO 1163-2, as indicated in Table 2. Table 2 Preparation of test specimens Type of profile Compound to be tested Type 1 PVC-U compound Type 2, Type 3 and Type 4 Each of the extruded compounds, as applicable The value of VST shall be coded according to Table 3. For Type 2, Type 3 and Type 4 profiles, as applicable, the values of the VST