BS ISO 16143-1-2014 Stainless steels for general purposes Corrosion-resistant flat products《一般用途不锈钢 耐腐蚀扁平产品》.pdf

《BS ISO 16143-1-2014 Stainless steels for general purposes Corrosion-resistant flat products《一般用途不锈钢 耐腐蚀扁平产品》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 16143-1-2014 Stainless steels for general purposes Corrosion-resistant flat products《一般用途不锈钢 耐腐蚀扁平产品》.pdf（60页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 16143-1:2014Stainless steels for general purposesPart 1: Corrosion-resistant flat productsBS ISO 16143-1:2014Incorporating corrigendum November 2014BS ISO 16143-1:2014 BRITISH STANDARDBS ISO 16143-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK

2、 implementation of ISO 16143-1:2014. The UK participation in its preparation was entrusted to TechnicalCommittee ISE/105, Steels for Heat Treatment, Alloy Steels, Free-Cutting Steels and Stainless Steels.A list of organizations represented on this committee can be obtained on request to its secretar

3、y.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 76079 2ICS 77.140.20Compliance with a British Standard cannot con

4、fer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2014.Amendments/corrigenda issued since publicationDate Text affectedDate Text affected30 November 2014 Implementation of ISO corrected text 1 Septembe

5、r 2014: See ISO foreword for detailsISBN 978 0 580 88019 3BS ISO 16143-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 16143-1:2014. The UK participation in its preparation was entrusted to TechnicalCommittee ISE/105, Steels for Heat Treatment, Alloy Ste

6、els, Free-Cutting Steels and Stainless Steels.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Stan

7、dards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 76079 2ICS 77.140.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2014.Amen

8、dments/corrigenda issued since publicationDate Text affected ISO 2014Stainless steels for general purposes Part 1: Corrosion-resistant flat productsAciers inoxydables pour usage gnral Partie 1: Produits plats en acier rsistant la corrosionINTERNATIONAL STANDARDISO16143-1Second edition2014-05-15Refer

9、ence numberISO 16143-1:2014(E)Corrected version2014-09-01ISO 16143-1:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic

10、 or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22

11、749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 16143-1:2014ISO 16143-1:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 24 Designation 25 Information to be supplied by the

12、purchaser. 26 Classification of grades 37 Requirements 37.1 Manufacturing process. 37.2 Delivery condition 37.3 Chemical composition 37.4 Susceptibility to intergranular corrosion 47.5 Mechanical properties 47.6 Surface quality . 47.7 Internal soundness 47.8 Dimensions, tolerances on dimensions, and

13、 shape . 47.9 Calculation of mass and tolerance of mass . 58 Inspection, testing, and conformance of products 58.1 General . 58.2 Inspection and testing procedures and types of inspection document . 58.3 Specific inspection and testing 68.4 Test methods . 68.5 Retests 79 Marking 7Annex A (informativ

14、e) Guidelines for further treatment (including heat treatment) in fabrication .36Annex B (informative) Designations of the steels given in Table 1 and of comparable grades covered in ASTM, EN, JIS, and GB standards 43Annex C (informative) Comparison list of abbreviations for process route/surface fi

15、nish of flat products given in Table 3 covered in ASTM and JIS standards 47Annex D (informative) Applicable dimensional standards 49Bibliography .50BS ISO 16143-1:2014ISO 16143-1:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards b

16、odies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizati

17、ons, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its furthe

18、r maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives

19、). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Intr

20、oduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to

21、conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 17, Steels, Subcommittee SC 4, Heat treatable and alloy s

22、teels.This second edition cancels and replaces the first edition (ISO 16143-1:2004), which has been technically revised.This corrected version of ISO 16143-1:2014 incorporates the following corrections: in Tables 1, 6, A.3 and B.1, the steel designation name “X2CrNbCu22” has been corrected to “X2CrT

23、iCu22”; normative reference ISO 15510 has been updated to the latest edition (2014); some cross-references and footnotes have been corrected or deleted.ISO 16143 consists of the following parts, under the general title Stainless steels for general purposes: Part 1: Corrosion-resistant flat products

24、Part 2: Corrosion-resistant semi-finished products, bars, rods and sections Part 3: Wireiv ISO 2014 All rights reservedBS ISO 16143-1:2014INTERNATIONAL STANDARD ISO 16143-1:2014(E)Stainless steels for general purposes Part 1: Corrosion-resistant flat products1 ScopeThis part of ISO 16143 specifies t

25、he technical delivery conditions for hot- or cold-rolled sheet/plate and strip for general purposes made of the most important corrosion-resistant stainless steel grades.NOTE 1 In the text, under the term “general purposes”, purposes other than the special purposes mentioned in References 1 to 4 are

26、 understood.NOTE 2 Heat-resistant steel grades can be found in ISO 4955 and they can be used for corrosion-resistant purposes.In addition to this part of ISO 16143, the general technical delivery requirements of ISO 404 are applicable.This part of ISO 16143 does not apply to components manufactured

27、by further processing of the product forms listed in the first paragraph where quality characteristics are altered as a result of such processing.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application.

28、 For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 148-1, Metallic materials Charpy pendulum impact test Part 1: Test methodISO 377, Steel and steel products Location and preparation of s

29、amples and test pieces for mechanical testingISO 404, Steel and steel products General technical delivery requirementsISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test i

30、n media containing sulfuric acidISO 6506-1, Metallic materials Brinell hardness test Part 1: Test methodISO 6507-1, Metallic materials Vickers hardness test Part 1: Test methodISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T)ISO 6892-1

31、:2009, Metallic materials Tensile testing Part 1: Method of test at room temperatureISO 6892-2, Metallic materials Tensile testing Part 2: Method of test at elevated temperatureISO 6929, Steel products VocabularyISO 10474, Steel and steel products Inspection documentsISO 14284, Steel and iron Sampli

32、ng and preparation of samples for the determination of chemical compositionISO 15510:2014, Stainless steels Chemical composition ISO 2014 All rights reserved 1BS ISO 16143-1:2014ISO 16143-1:2014(E)ISO/TS 4949, Steel names based on letter symbolsISO/TR 9769, Steel and iron Review of available methods

33、 of analysis3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 6929 and the following apply.3.1corrosion-resistant stainless steelsteel, with at least 10,5 % (mass fraction) Cr and a maximum of 1,2 % (mass fraction) C, for which resistance to corrosion i

34、s of primary importance3.2product formshape of a productNote 1 to entry: Different forms of products are given in ISO 6929.4 DesignationFor the steel grades covered by this part of ISO 16143, the steel names as given in the tables are allocated in accordance with ISO/TS 4949.For the steel grades cov

35、ered by this part of ISO 16143, the steel numbers as given in the tables are allocated in accordance with ISO 15510.5 Information to be supplied by the purchaserIt shall be the responsibility of the purchaser to specify all requirements that are necessary for products covered by this part of ISO 161

36、43. Such requirements to be considered include, but are not limited to, the following:a) the desired quantity;b) the product form (strip or sheet/plate);c) the number of the appropriate dimensional standard, e.g. ISO 9444-1, ISO 9444-2, ISO 9445-1, ISO 9445-2, and ISO 18286 (see Annex D), the nomina

37、l dimensions, plus any choice of requirements;d) the type of material (steel);e) the number of this part of ISO 16143 (i.e. ISO 16143-1);f) the steel name or steel number;g) if, for the relevant steel in Tables 4 to 8, more than one treatment condition is covered, the symbol for the desired heat tre

38、atment or cold-worked condition;h) the desired process route/surface finish (see Table 3);i) if a verification of internal soundness is required for flat products with thickness 6 mm, requirements can be agreed at the time of enquiry and order (see 7.7);j) any further optional test agreed between th

39、e manufacturer and purchaser at the time of enquiry and order see 8.2.3 b);k) the type of inspection document and its designation in accordance with ISO 10474 (see 8.2.1).2 ISO 2014 All rights reservedBS ISO 16143-1:2014ISO 16143-1:2014(E)EXAMPLE 5 t of cold-rolled narrow strip in accordance with IS

40、O 9445-1 with a specified thickness of 0,25 mm, precision thickness tolerance (P), with a specified width of 250 mm, precision tolerance on width (P) and with restricted tolerances on edge camber (R) made of a steel grade with name X5CrNi18-10 and number 4301-304-00-I as specified in ISO 16143-1, in

41、 process route 2D and inspection certificate 3.1 as specified in ISO 10474, is designated as follows:5 t cold-rolled narrow strip ISO 9445-1 - 0,25P 250P - R Steel ISO 16143-1 - X5CrNi18-10 + 2D ISO 10474 3.1or5 t cold-rolled narrow strip ISO 9445-1 - 0,25P 250P - R Steel ISO 16143-1 - 4301-304-00-I

42、 + 2D ISO 10474 3.16 Classification of gradesCorrosion-resistant stainless steels covered in this part of ISO 16143 are classified according to their structure into austenitic steels, austenitic-ferritic steels, ferritic steels, martensitic steels, or precipitation-hardening steels.7 Requirements7.1

43、 Manufacturing processUnless a special steelmaking process is agreed upon at the time of ordering, the steelmaking process shall be at the discretion of the manufacturer. When he so requests, the purchaser shall be informed what steelmaking process is being used.7.2 Delivery conditionThe products sh

44、all be supplied in the delivery condition agreed upon in the order, by reference to the process route given in Table 3 and, where different alternatives exist, to the treatment conditions given in Tables 4 to 8, 14, and 16 (see also Annex A).7.3 Chemical composition7.3.1 The chemical composition req

45、uirements given in Table 1 apply with respect to the chemical composition of the cast analysis.7.3.2 The product analysis can deviate from the limiting values for the cast analysis given in Table 1 by the values listed in Table 2. ISO 2014 All rights reserved 3BS ISO 16143-1:2014ISO 16143-1:2014(E)7

46、.4 Susceptibility to intergranular corrosionReferring to resistance to intergranular corrosion as defined in ISO 3651-2, for ferritic, austenitic, and austenitic-ferritic steels, the specifications in Tables 4, 5, and 6 apply.The susceptibility of stainless steels to intergranular corrosion is depen

47、dent on the type of environment and therefore cannot always be clearly ascertained through standard laboratory tests. The selection of the test or tests to be agreed upon should be based on experience with the use of the selected grade of steel in the intended environment.7.5 Mechanical propertiesTh

48、e mechanical properties at room temperature as specified in Tables 4 to 8 apply for the relevant specified heat-treatment condition. This does not apply to the process route 1U (hot rolled, not heat treated, not descaled). If, by agreement at the time of ordering, the products are to be supplied in

49、a non-heat-treated condition, the mechanical properties specified in Tables 4 to 8 shall be obtainable from reference test pieces which have received the appropriate heat treatment (simulated heat treatment).The values in Tables 9 to 13 apply for the 0,2 %- and 1 %-proof strength at elevated temperatures.For cold-worked products, the 0,2 %-proof strength levels at ambient temperature as specified in Table 14 apply. The available 0,2 %-proof strength levels in the cold-worked condition are in