BS ISO 13799-2012 Ships and marine technology Ship-s mooring and towing fittings Recessed bitts (Casting type)《船舶与海洋技术 船舶系泊和拖曳附件 嵌入式缆柱(铸造式)》.pdf

《BS ISO 13799-2012 Ships and marine technology Ship-s mooring and towing fittings Recessed bitts (Casting type)《船舶与海洋技术 船舶系泊和拖曳附件 嵌入式缆柱(铸造式)》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 13799-2012 Ships and marine technology Ship-s mooring and towing fittings Recessed bitts (Casting type)《船舶与海洋技术 船舶系泊和拖曳附件 嵌入式缆柱(铸造式)》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 13799:2012Ships and marine technology Ships mooring and towingfittings Recessed bitts(Casting type)BS ISO 13799:2012 BRITISH STANDARDNational forewordThis British Standard

2、 is the UK implementation of ISO 13799:2012.The UK participation in its preparation was entrusted to TechnicalCommittee SME/32/-/4, Ships and marine technology - Outfitting anddeck machinery.A list of organizations represented on this committee can beobtained on request to its secretary.This publica

3、tion does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 69757 9ICS 47.020.50Compliance with a British Standard cannot confer immunity fro

4、mlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2012.Amendments issued since publicationDate Text affectedBS ISO 13799:2012 ISO 2012Ships and marine technology Ships mooring and towing fittings Recessed bitts (Ca

5、sting type)Navires et technologie maritime Corps-morts et ferrures de remorquage de navires Bittes damarrage encastres (type moulage)INTERNATIONAL STANDARDISO13799First edition2012-07-01Reference numberISO 13799:2012(E)BS ISO 13799:2012ISO 13799:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTEC

6、TED DOCUMENT ISO 2012All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs memb

7、er body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 13799:2012ISO 13799:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroductio

8、n v1 Scope 12 Normative references . 13 Terms and definitions . 14 Classification 14.1 Type . 14.2 Nominal sizes . 15 Dimensions . 16 Materials . 27 Construction . 28 Manufacturing and inspection . 29 Marking . 2Annex A (informative) Basis for strength assessment of recessed bitts (Casting type) 5Bi

9、bliography . 7BS ISO 13799:2012ISO 13799:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each me

10、mber body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International E

11、lectrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adop

12、ted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of paten

13、t rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 13799 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 4, Outfitting and deck machinery.iv ISO 2012 All rights reservedBS ISO 13799:2012ISO 13799:2012(E)Introductio

14、nThe recessed bitt is a type of ships towing fitting installed on the side shell of the ship.The recessed bitts are normally provided to easily attach the towing lines where the height of the mooring deck is too high. ISO 2012 All rights reserved vBS ISO 13799:2012BS ISO 13799:2012Ships and marine t

15、echnology Ships mooring and towing fittings Recessed bitts (Casting type)1 ScopeThis International Standard specifies the design, size and technical requirements for casting type recessed bitts to meet normal towing requirements.2 Normative referencesThe following referenced documents are indispensa

16、ble for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.IMO Circular MSC/Circ.1175, Guidance on shipboard towing and mooring equipment3 Terms and definitio

17、nsFor the purposes of this document, the following terms and definitions apply.3.1safe working loadSWLmaximum load in kN on the rope that should normally be applied in service conditions.4 Classification4.1 TypeDepending on the size and strength of the material, recessed bitts shall be classified as

18、 the following six types: Type 75 nominal size 850, casting material having a yield point of not less than 235 N/mm2 Type 110 nominal size 850, casting material having a yield point of not less than 350 N/mm2 Type 135 nominal size 850, casting material having a yield point of not less than 430 N/mm2

19、 Type 100 nominal size 920, casting material having a yield point of not less than 235 N/mm2 Type 150 nominal size 920, casting material having a yield point of not less than 350 N/mm2 Type 180 nominal size 920, casting material having a yield point of not less than 430 N/mm24.2 Nominal sizesThe nom

20、inal sizes of recessed bitts are denoted by reference to the outside diameter of the bitt, in millimetres.The nominal size is: 850 and 920.5 DimensionsRecessed bitts have dimensions and particulars in accordance with Table 1 and Figure 1.INTERNATIONAL STANDARD ISO 13799:2012(E) ISO 2012 All rights r

21、eserved 1BS ISO 13799:2012ISO 13799:2012(E)6 MaterialsThe materials of the following components shall be used for manufacturing the recessed bitts: Type 75 and type 100: weldable steel casting having a yield point of not less than 235 N/mm2. Type 110 and type 150: weldable steel casting having a yie

22、ld point of not less than 350 N/mm2. Type 135 and type 180: weldable steel casting having a yield point of not less than 430 N/mm2.7 Construction7.1 The welding connections to the hull shall be guaranteed reliable transmission of the maximum loading of the recessed bitts to hull construction without

23、 any plastic deformation or cracks.7.2 The hull construction which the recessed bitts are installed on shall be reinforced by carlings, stiffeners, etc.7.3 The recessed bitts shall be considered as a part of the hull side shell construction.8 Manufacturing and inspection8.1 All surfaces of the reces

24、sed bitts, including welding, shall be free from any visible flaws or imperfections.8.2 All surfaces in contact with the ropes shall be free from surface roughness or irregularities likely to cause damage to the ropes by abrasion.8.3 The recessed bitts shall be coated externally with an anti-corrosi

25、on protective finish.9 Marking9.1 The safe working load (SWL) for the intended use for the recessed bitts shall be noted in the towing and mooring plan available on board for the guidance of the shipmaster as specified in MSC/Circ.1175.9.2 The actual SWL on board shall be determined by considering t

26、he reinforcement around the recessed bitts, and it shall be marked on the towing and mooring plan. The actual SWL shall not be over the SWL indicated in this International Standard.9.3 The recessed bitts shall be clearly marked with their SWL by weld bead or equivalent. The SWL shall be expressed in

27、 tonnes (letter t) and be placed so that it is not obscured during operation of the fitting.EXAMPLE SWL XXX t2 ISO 2012 All rights reservedBS ISO 13799:2012ISO 13799:2012(E)Dimensions in millimetresaSWL marking.bSide shell.NOTE 1 Bitt welding method to hull connection is to be approved by Classifica

28、tion Society.NOTE 2 Centre marking by punching for easy installation.Figure 1 Recessed bitts ISO 2012 All rights reserved 3BS ISO 13799:2012ISO 13799:2012(E)Table 1 Dimensions and SWL of recessed bittsDimensions in millimetresNominal sizeDnD1d1b1b2R1R2R3R4R5R6R7R8850 850 750 200 280 450 500 250 65 1

29、15 50 55 250920 920 812 216 300 490 544 270 70 124 55 60 270Nominal sizeDnR9R10t1f1f2f3f4f5h1h2h3850 180 30 50 500 250 180 248,7 263,4 400 190 110920 195 30 54 544 270 195 274,3 290,4 430 205 110Nominal sizeDnTypeMaterial(minimum yield strength)SWLCalculated weight(kg)(kN) (t)850Type 75 235 N/mm2736

30、 75 770Type 110 350 N/mm21 079 110 770Type 135 430 N/mm21 324 135 770920Type 100 235 N/mm2981 100 826Type 150 350 N/mm21 472 150 826Type 180 430 N/mm21 766 180 826aThe SWL is the maximum applicable rope tension.The SWLs shown in this table are for reference only. These are based on the loadings as m

31、entioned in Annex A.bThe calculated weight is for reference only.4 ISO 2012 All rights reservedBS ISO 13799:2012ISO 13799:2012(E)Annex A (informative) Basis for strength assessment of recessed bitts (Casting type)A.1 GeneralThe strength of the recessed bitts was evaluated by finite element model ana

32、lysis and determined based on the following design criteria.A.2 LoadingA.2.1 The recessed bitts are to be designed to withstand the loads imposed by the towing ropes.A.2.2 The recessed bitts are to be designed to withstand the following load case.They are to be designed to withstand the combined loa

33、d produced by P imposed as below positions.KeyP towing forceFigure A.1 Combined loads by towing ropeA.3 Load and stress criterionUnder the SWL, the following stress criterion was adopted. The combined stress is limited to 85 % of the yield stress of the material. ISO 2012 All rights reserved 5BS ISO

34、 13799:2012ISO 13799:2012(E)A.4 Wear-down allowances and corrosion additionsA.4.1 Wear-down allowancesFor the strength calculation, wear-down of 2 mm is to be deducted from the gross thickness, where the rope is rubbing the surface.A.4.2 Corrosion additionsThe corrosion margin was already included i

35、n the safety factor and 2 mm wear-down allowance.6 ISO 2012 All rights reservedBS ISO 13799:2012ISO 13799:2012(E)Bibliography1 IACS UR A2, Shipboard fittings and supporting hull structures associated with towing and mooring on conventional vessels2 OCIMF, Mooring Equipment Guidelines (MEG3)3 ISO 499

36、0, Steel castings General technical delivery requirements4 ISO 9477, High strength cast steels for general engineering and structural purposes ISO 2012 All rights reserved 7BS ISO 13799:2012ISO 13799:2012(E) ISO 2012 All rights reservedICS 47.020.50Price based on 7 pagesThis page deliberately left b

37、lankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other st

38、andardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Stan

39、dards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the tec

40、hnical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscrib

41、ers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, internati

42、onal and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise req

43、uested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantia

44、l discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at informat

45、ion about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the intern

46、ational standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, ph

47、otocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: