BS ISO 13254-2010 Thermoplastics piping systems for non-pressure applications - Test method for watertightness《非承压用途热塑性管路系统 水密性试验方法》.pdf

《BS ISO 13254-2010 Thermoplastics piping systems for non-pressure applications - Test method for watertightness《非承压用途热塑性管路系统 水密性试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 13254-2010 Thermoplastics piping systems for non-pressure applications - Test method for watertightness《非承压用途热塑性管路系统 水密性试验方法》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO13254:2010ICS 23.040.20; 91.140.80NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDThermoplastics pipingsystems for non-pressure applications Test method forwatertightnessThis British Standardwas published under theauthority of the StandardsPolicy and Strat

2、egyCommittee on 30 June2010 BSI 2010ISBN 978 0 580 66735 0Amendments/corrigenda issued since publicationDate CommentsBS ISO 13254:2010National forewordThis British Standard is the UK implementation of ISO 13254:2010.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/88/1

3、, Plastics piping for non-pressure applications.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a

4、 British Standard cannot confer immunityfrom legal obligations.BS ISO 13254:2010Reference numberISO 13254:2010(E)ISO 2010INTERNATIONAL STANDARD ISO13254First edition2010-05-01Thermoplastics piping systems for non-pressure applications Test method for watertightness Systmes de canalisations thermopla

5、stiques pour applications sans pression Mthode dessai de ltanchit leau BS ISO 13254:2010ISO 13254:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are

6、 embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorpor

7、ated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a

8、 problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical,

9、including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Pu

10、blished in Switzerland ii ISO 2010 All rights reservedBS ISO 13254:2010ISO 13254:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International S

11、tandards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, als

12、o take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committe

13、es is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possi

14、bility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13254 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommit

15、tee SC 1, Plastics pipes and fittings for soil, waste and drainage (including land drainage). BS ISO 13254:2010BS ISO 13254:2010INTERNATIONAL STANDARD ISO 13254:2010(E) ISO 2010 All rights reserved 1Thermoplastics piping systems for non-pressure applications Test method for watertightness 1 Scope Th

16、is International Standard specifies a test method for watertightness of thermoplastics products fabricated from more than one piece for non-pressure applications, and joints of thermoplastics piping systems for non-pressure applications. 2 Principle A test assembly comprising either a fabricated pro

17、duct or an assembly of pipes and/or fittings is subjected to a given internal hydrostatic pressure for a given time period during which the leaktightness of the fabricated product or the joint is verified by inspection. NOTE It is assumed that the following test parameters are set by the referring s

18、tandard: a) the sampling procedure (see 4.1 and Clause 5); b) the number of test pieces (see 4.2). 3 Apparatus 3.1 End-sealing devices, having a size and using a sealing method that are appropriate to the type of joint assembly under test. The devices shall be restrained in such a manner that does n

19、ot exert longitudinal forces on the joint assembly and prevents the devices or the assembly under test from separating under pressure. The mass of the devices shall not be permitted to influence the angular deflection to be applied (see 5.2). 3.2 Hydrostatic pressure source, connected to one end of

20、at least one end-sealing device, capable of applying the required pressure gradually and evenly in accordance with 5.4, and then of keeping it constant to within21%+for the required duration of test (see Clause 5). 3.3 Bleed valve, capable of venting air when the hydrostatic pressure is applied to t

21、he test piece. 3.4 Pressure-measuring device, capable of checking conformity to the required test pressure (see 3.2 and Clause 5). BS ISO 13254:2010ISO 13254:2010(E) 2 ISO 2010 All rights reserved4 Test pieces 4.1 Preparation of test pieces The test piece shall comprise either a fabricated fitting o

22、r an assembly of (a) pipe section(s) (with or without sockets) and/or fitting(s), including at least one joint of the type under test (see Figure 1). To assist air removal, the test pieces may be inclined by up 12. Dimensions in millimetres Key 1 fixed points 2 sealing plug with water outlet and end

23、 restraint (see 3.1) 3 loose bushes enabling all sizes of pipes to be accommodated on the same test fixture 4 fixed component 5 sealing plug with water inlet, air outlet and end restraint aWater inlet. bAir outlet. cWater outlet. dDirection of movement for angular deflection, if applicable (see 5.2)

24、. Figure 1 Typical arrangement The assembly of the joint(s) shall be carried out in accordance with the manufacturers instructions. The assembly shall comprise the combination of the smallest available spigot end and the largest available socket or socket groove diameter within the applicable tolera

25、nce(s) and obtained by sampling in accordance with the referring standard. The relevant diameters of the selected spigots and sockets shall be measured and recorded. 4.2 Number of test pieces The number of test pieces shall be specified in the referring standard. BS ISO 13254:2010ISO 13254:2010(E) I

26、SO 2010 All rights reserved 35 Procedure 5.1 Carry out the following procedure at a temperature of (23 5) C using cold tap water, without permitting any condensation to form on the surface of the test piece. 5.2 Mount the test piece in the apparatus. If the joint to be tested permits angular deflect

27、ion, arrange the test assembly such that the joint(s) under test is (are) subject to its (their) maximum angular deflection, as stated by the manufacturer for the specific joint, with regard to the axes of the components thus joined. 5.3 When testing in accordance with 5.4 and 5.5, monitor the test

28、piece for, and record any evidence of, leakage. 5.4 Introduce water into the test piece, while bleeding off all air, and apply the hydrostatic pressure in the following manner: a) accelerated procedure for fabricated products: unless otherwise specified in the referring standard, apply an hydrostati

29、c pressure of 0,5 bar1)and maintain it for at least 1 min; b) for assemblies of pipes and/or fittings which are not fabricated: raise the hydrostatic pressure smoothly over a time period not greater than 15 min to 0,5 bar and maintain that pressure for at least 15 min. 5.5 Depressurize, drain and di

30、smantle the test piece. Inspect for and record any changes in the appearance of the components tested. 6 Test report The test report shall include the following information: a) a reference to this International Standard, i.e. ISO 13254:2010, and the referring standard; b) the complete identification

31、 of the components (e.g. fittings, pipes, assemblies) comprising the joints under test and their respective diameters, in millimetres (see 4.1); c) the test temperature (see 5.1), in degrees Celsius; d) the test pressure, in bar; e) the time period under pressure, in minutes; f) the angle of deflect

32、ion applied to the joint, if applicable (see 5.2); g) a statement that the joint did not leak or, if applicable, a report of the signs of leakage or rupture, their position(s) and the pressure at which they occurred; h) any change in the appearance of the components of the test piece(s) during testi

33、ng or immediately afterwards; i) any factor that could have affected the results, such as any incident or any operating details not specified in this International Standard; j) the date of the test. 1) 1 bar = 0,1 MPa = 105Pa; 1 MPa = 1 N/mm2. BS ISO 13254:2010ISO 13254:2010(E) ICS 23.040.20; 91.140

34、.80 Prix bas sur 3 pages ISO 2010 All rights reserved BS ISO 13254:2010This page has been intentionally left blank BS ISO13254:2010BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national b

35、ody responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest a

36、mendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be fou

37、nd on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards p

38、ublications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation o

39、f those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information servic

40、es are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards

41、. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at htt

42、p:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitt

43、ed in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: