BS EN 60512-16-4-2008 Connectors for electronic equipment - Tests and measurements - Part 16-4 Mechanical tests on contacts nand terminations — Test 16d Tensile nstrength (crimped .pdf

《BS EN 60512-16-4-2008 Connectors for electronic equipment - Tests and measurements - Part 16-4 Mechanical tests on contacts nand terminations — Test 16d Tensile nstrength (crimped .pdf》由会员分享，可在线阅读，更多相关《BS EN 60512-16-4-2008 Connectors for electronic equipment - Tests and measurements - Part 16-4 Mechanical tests on contacts nand terminations — Test 16d Tensile nstrength (crimped .pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60512-16-4: 2008Connectors for electronic equipment Tests and measurements Part 16-4: Mechanical tests on contacts and terminations Test 16d: Tensile strength (crimped connections)ICS 31.220.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g5

2、4g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60512-16-4:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 August 2008 BSI 2008ISBN 978 0 580 55910 5National fore

3、wordThis British Standard is the UK implementation of EN 60512-16-4:2008. It is identical to IEC 60512-16-4:2008. The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizatio

4、ns represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Ame

5、ndments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARD EN 60512-16-4 NORME EUROPENNE EUROPISCHE NORM July 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central S

6、ecretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-16-4:2008 E ICS 31.220.10 English version Connectors for electronic equipment - Tests and measurements - Part 16-4: Mecha

7、nical tests on contacts and terminations - Test 16d: Tensile strength (crimped connections) (IEC 60512-16-4:2008) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 16-4: Essais mcaniques des contacts et des sorties - Essai 16d: Rsistance la traction (connexions serties) (CEI 6051

8、2-16-4:2008) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 16-4: Mechanische Prfungen an Kontakten und Anschlssen - Prfung 16d: Zugfestigkeit von Crimpverbindungen (IEC 60512-16-4:2008) This European Standard was approved by CENELEC on 2008-07-01. CENELEC members are

9、bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to th

10、e Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the s

11、ame status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, No

12、rway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 48B/1879/FDIS, future edition 1 of IEC 60512-16-4, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic

13、 equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-16-4 on 2008-07-01. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the structure of the EN 60512 series. The following dates were fixed: latest date by whi

14、ch the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-07-01 Annex ZA has been added by CENELEC. _ Endorsement notice The

15、 text of the International Standard IEC 60512-16-4:2008 was approved by CENELEC as a European Standard without any modification. _ 2 BS EN 60512-16-4:2008CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 16-4: Mechanical tests on contacts and terminations Test 16d: Tensile strength (cr

16、imped connections) 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 i

17、s to detail a standard test method to determine the tensile strength of a crimped connection. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edi

18、tion of the referenced document (including any amendments) applies. IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a: Visual examination 3 Preparations 3.1 Preparation of specimen The specimen shall consist of a contact or terminal crimp

19、ed to a conductor. This shall be done in accordance with the relevant detail specification and tooling specifications given therein. If the specimen has a cable insulation support or any other clamping device not part of the conductor crimp, this shall be rendered inoperative such that it has no inf

20、luence on the test. Any preconditioning required by the detail specification shall be applied. NOTE It may be convenient to crimp a specimen to each end of a conductor; if this is done such a specimen shall be considered as one specimen. 3.2 Equipment A tensile testing machine with relevant fixtures

21、 able to comply with the test procedure herein detailed shall be required. 3.3 Mounting If mounting of the specimen is appropriate, it shall be as specified in the detail specification. The specimen shall be fixed in the jaws of a tensile testing machine such that the crimp barrel of the specimen is

22、 nor damaged or otherwise affected by the jaws. The fixing of the specimen shall be such that the tensile load is applied axially to the crimped connection under test. 3 BS EN 60512-16-4:20084 Test method The testing machine head, travelling at a rate of between 25 and 50 mm/min, shall apply tension

23、 to the specimen until the conductor is pulled out of the crimp barrel or the wire or the specimen breaks. 5 Measurements and requirements 5.1 Before testing Visual examination according to IEC 60512-1-1 shall be carried out. 5.2 During testing The load to cause breakage shall be recorded. Also, the

24、 testing machine head rate of travel in mm/min shall be recorded. NOTE The elongation versus load graph may be of interest to users. However, this information is not a requirement of this part of IEC 60512. 5.3 After testing Visual examination according to IEC 60512-1-1 shall be carried out. The nat

25、ure and characterics of the breakage shall be recorded. 6 Details to be specified When this test is required by a detail specification, the following shall be given therein: whether preconditioning is required; cable/wire/conductor size(s) to be used; details of assembly and/or crimping tooling; whe

26、ther a lubricant, including that for assembly and/or crimping tooling, is to be used; whether special mounting of the specimen is required; number of specimens to be tested; minimum ultimate load (if none is specified the values in IEC 60352-2 shall be referenced); any deviation from the standard te

27、st method. 4 BS EN 60512-16-4:2008Bibliography IEC 60352-2, Solderless connections Part 2: Crimped connections General requirements, test methods and practical guidance _ 5 BS EN 60512-16-4:2008NOTE Harmonized as EN 60352-2:2006 (not modified). Annex ZA(normative) Normative references to internation

28、al publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendme

29、nts) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 -1)Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: V

30、isual examination EN 60512-1-1 20022)1)Undated reference. 2)Valid edition at date of issue. 6 BS EN 60512-16-4:2008blankBS EN 60512-16-4: 2008BSI Group Headquarters389 Chiswick High Road,London W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards Institution (BSI)BSI is the independent nat

31、ional body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess th

32、e latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of wh

33、ich can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and forei

34、gn standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI

35、implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic

36、 information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the p

37、urchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is availa

38、ble on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored i

39、n a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: